Value of PET and PET/CT in the diagnostics of prostate and penile cancer.

B. Scher,M. Seitz,W. Albinger,M. Reiser,B. Schlenker,C. Stief,U. Mueller-Lisse,S. Dresel

DOI: https://doi.org/10.1007/978-3-540-31203-1_13

Abstract:

What problem does this paper attempt to address?

Extrusion Foaming Of Lightweight Polystyrene Composite Foams With Controllable Cellular Structure For Sound Absorption Application

Yanpei Fei,Wei Fang,Mingqiang Zhong,Jiangming Jin,Ping Fan,Jintao Yang,Zhengdong Fei,Lixin Xu,Feng Chen

DOI: https://doi.org/10.3390/polym11010106

IF: 5

2019-01-01

Polymers

Abstract:Polymer foams are promising for sound absorption applications. In order to process an industrial product, a series of polystyrene (PS) composite foams were prepared by continuous extrusion foaming assisted by supercritical CO2. Because the cell size and cell density were the key to determine the sound absorption coefficient at normal incidence, the bio-resource lignin was employed for the first time to control the cellular structure on basis of hetero-nucleation effect. The sound absorption range of the PS/lignin composite foams was corresponding to the cellular structure and lignin content. As a result, the maximum sound absorption coefficient at normal incidence was higher than 0.90. For a comparison, multiwall carbon nanotube (MWCNT) and micro graphite (mGr) particles were also used as the nucleation agent during the foaming process, respectively, which were more effective on the hetero-nucleation effect. The mechanical property and thermal stability of various foams were measured as well. Lignin showed a fire retardant effect in PS composite foam.
Fabrication of biodegradable poly (lactic acid)/carbon nanotube nanocomposite foams: Significant improvement on rheological property and foamability

Yang Li,Dexian Yin,Wei Liu,Hongfu Zhou,Yuxia Zhang,Xiangdong Wang

DOI: https://doi.org/10.1016/j.ijbiomac.2020.07.094

IF: 8.2

2020-11-01

International Journal of Biological Macromolecules

Abstract:<p>Recently, biodegradable macromolecules have been highly desired as a promising alternative for traditional oil-based plastics to work out the eco crisis and biological health problems triggered by microplastics. Herein, we presented a simple, effective, environmentally friendly and CO<sub>2</sub>-based foaming methodology for fabricating ultra-low-density poly (lactic acid)/carbon nanotube (PLA/CNTs) nanocomposite foam. By the gradual incorporation of CNTs, three kinds of networks generated in PLA/CNTs nanocomposites and had a distinct reinforcement influence on their melt viscoelasticity, which testified by transmission electron microscope, electrical conductivity and rheological property measurements, severally. Specifically, the storage modulus of PLA/CNTs nanocomposites were 3 orders of magnitude higher in contrast to pure PLA. Interestingly, relative to that under regular differential scanning calorimetry (DSC), a double melting peak phenomenon appeared in the high-pressure DSC curves of diverse PLA specimens. Biodegradable PLA/CNTs nanocomposite foam was successfully fabricated with a super-high volume expansion ratio (VER) of 49.6 times, which could offer a promising strategy for developing other thermoplastic polyester foams with ultra-high VER to obtain some unique functional attributes.</p>

polymer science,biochemistry & molecular biology,chemistry, applied
Rheological behavior, crystallization properties, and foaming performance of chain-extended poly (lactic acid) by functionalized epoxy

Ming Li,Shengnan Li,Bujin Liu,Tuanhui Jiang,Di Zhang,Lushuai Cao,Li He,Wei Gong

DOI: https://doi.org/10.1039/d1ra06382k

2021-10-05

Abstract:The inherently linear poly (lactic acid) suffers unsatisfying foaming behavior due to its low melt strength and poor crystallization properties. To overcome this drawback, a random terpolymer of ethylene, acrylic ester and glycidyl methacrylate (EGMA) was employed to improve the rheological behavior, crystallization properties, and foaming performance of poly (lactic acid) (PLA) through a chain extension reaction. The branched/micro-crosslinked structure formed by the chain extension reaction between EGMA and PLA effectively improved the dynamic rheological properties of PLA. As the content of EGMA increased from 0 wt% to 20 wt%, the crystal nucleation and crystal growth rate of various PLA samples have been significantly accelerated, resulting in a larger number and smaller size of spherulites, and the crystallinity of various PLA samples increased from 7.9% to 38.54%. The cell size of various PLA foams decreased from 53.5 to 22.0 μm and the cell density increased from 3.5 × 106 cells per cm3 to 2.5 × 107 cells per cm3, meanwhile, the cellular morphology of PLA foam was obviously improved. Moreover, the actual weight loss of PLA foams reached 26.1%, which is higher than the theoretical weight loss.
Foamability of all‐green polylactide/rice straw pulp biocomposites through continuous extrusion process: Effects of pulping and reactive compatibilization

Danial Abbasi,Mahdis Jafari,Pedram Bahrami,Farkhondeh Hemmati,Jamshid Mohammadi‐Roshandeh

DOI: https://doi.org/10.1002/cjce.25361

2024-06-25

The Canadian Journal of Chemical Engineering

Abstract:Soda‐pulping and bleaching modification of rice straw along with the use of a reactive compatibilizer improve the PLA foamability. In the present work, the processability of poly(lactic acid) (PLA) in the extrusion foaming process was improved by using rice straw (RS) as an agricultural waste. In order to extrude a sustainable lightweight foam, the soda‐pulping and bleaching modification were performed on the RS particles, which resulted in the attainment of purified micron‐sized cellulosic fibre with higher aspect ratio. The addition of these fibres, with larger interfacial area between filler and matrix, to the PLA melt enhanced the foam void fraction and cell density more than one order of magnitude. The use of a reactive compatibilizer in the biocomposite showed further beneficial effects on the PLA foamability. The used reactive compatibilizer, with the ability of simultaneous reactions with the end groups of PLA macromolecules and hydroxyl groups of the lignocellulosic pulp, in the biocomposite noticeably improved the viscoelastic properties of melt and lengthened the macromolecule relaxation times. As a result, the biocomposite melt with higher melt strength was obtained, which kept the melt integrity during the bubble growth stage, hindered the cell coalescence, and retained a larger volume of gas inside the melt. Contrary to these influences, the compatibilization activity of this additive weakened the heterogeneous nucleation role of the cellulosic fibres. However, by choosing proper pulp loading, the extrusion of a lightweight biodegradable PLA‐based biocomposite foam can be feasible, which can be used in interior construction applications.

engineering, chemical
Modified standard polylactic acid (PLA) for extrusion foaming

S. Göttermann,S. Weinmann,C. Bonten,T. Standau,V. Altstädt

DOI: https://doi.org/10.1063/1.4965522

2016-01-01

AIP Conference Proceedings

Abstract:Polymeric foams are used in disposable packaging because of their low density, high impact resistance and the low material consumption. Nowadays they are often made of petroleum-based extruded polystyrene foam (XPS). The use of biodegradable and biobased polymers in short-living packaging could be an ecological benefit. One of PLA´s shortcomings is its poor melt viscosity and poor melt stiffness. To foam a standard, cost effective man-produced PLA, it must be modified to increase its low melt strength. In the presented work the effects of grafting, crosslinking and chain extension on the melt strength were investigated. The addition of different modifiers and the performance of the reaction were performed by means of reactive extrusion on a twin screw extruder. The rheological properties in shear and elongation deformation, the foam densities, the cell sizes and the morphology were examined. The melt viscosity was increased and could be correlated to a higher molecular weight and broader molecular weight distribution. Foams with fine and closed-cell structure with relatively thin cell walls and bars were made in batchfoaming experiments. Here, the densities of the modified PLAs could be reduced to one third as compared to the unmodified PLA. The aim to generate bio-foams with standard and cost effective PLA was achieved.
Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Kun Cao,ZhanQuan Lu,Yan Li,ZhenHua Chen,Zhicheng Shen,Zhen Yao

2010-01-01

Abstract:The reactive extrusion of maleic anhydride grafted polypropylene (PP-g-MAH) with ethylenediamine (EDA) as coupling agent was carried out in a co-rotating twin-screw extruder to produce long chain branched polypropylene (LCBPP). Part of PP-g-MAH was replaced by maleic anhydride grafted high-density polyethylene (HDPE-g-MAH) or linear low-density polyethylene (LLDPE-g-MAH) to obtain hybrid long chain branched (LCB) polymers. Compared with the linear PP, PE and their blends, the LCB polyolefins exhibit excellent dynamic shear and transient extensional rheological characteristics such as increased dynamic modulus, higher low-frequency complex viscosity, significantly enhanced melt strength and strain-hardening behaviors. LCB polymers also have higher tensile strength, tensile modulus, impact strength and lower elongation at break than linear polymer and their blends. Supercritical carbon dioxide (scCO2) was introduced in the reactive extrusion process. With the presence of scCO 2, the motor current of twin extruder was decreased and LCB polyolefins with lower MFR, higher complex viscosity and increased tensile strength and modulus were obtained. This indicates that the application of scCO2 can reduce the viscosity of melt in extruder, enhance the diffusion of reactive species, facilitate the reaction between functional groups, and increase the LCB density. The foaming behavior of both linear and LCB polyolefins were studied. The results show that cellular materials produced from the LCB polyolefins have higher weight reduction, smaller cell size and better mechanical properties than those produced from the linear polymers.
Extruded polylactide bead foams using anhydrous supercritical CO2 extrusion foaming

Yaozhuo Su,Pengke Huang,Jie Sun,Jiali Chen,Hao Zheng,Haibin Luo,Yunkai Chong,Yongqing Zhao,Fei Wu,Wenge Zheng

DOI: https://doi.org/10.1002/app.54557

IF: 3

2023-08-19

Journal of Applied Polymer Science

Abstract:Schematic diagram of preparing PLA beads using one‐step anhydrous supercritical CO2 extrusion foaming technology. Polylactic acid (PLA) is a bio‐based and biodegradable polymer. It is challenging to prepare PLA bead foams at a large scale in an efficient manner. Herein, beads of modified PLA are foamed by one‐step anhydrous supercritical CO2 extrusion. This dramatically shortens the production time, prevents the PLA from pyrohydrolysis, and avoids wastewater generation. The melt strength of the PLA is increased from 0.8 to 16.7 cN using a chain extender. The morphologies and microstructures of bead foams are analyzed. In the case of the PLA bead foam obtained by extrusion foaming combined with wind‐cooling pelletizing technology, the expansion ratio is higher than 13, the pore morphology is typical cellular structures, and the surface is glossy. The advantages and shortcomings of the PLA beads are also investigated. It is beneficial to promote the continuous preparation of PLA bead foams and other polymer beads like PS, and PP, which can be used in the fields of green packing, sound absorption, cold‐chain logistics, and so forth.

polymer science
Study on Foaming Properties of PLA/NCC Microcellular Foam Materials

Mengxia Lin,Pingping Zou,Ping Zhang,Jinzhou Chen,De Gao

DOI: https://doi.org/10.3969/j.issn.1001-3539.2013.10.022

2013-01-01

Abstract:Poly(lactic acid)/nanocrystalline cellulose (PLA/NCC) microcellular foams were prepared with supercritical CO2 as foaming agent and PEG as compatibilizer. The effects of the content of NCC and PEG on the volume expansion rate and cell morphology of PLA/NCC foams were discussed. The effects of different soaking time and foaming temperature on the volume expansion rate and cell morphology of PLA/NCC foams were also studied. The results indicate that nanoparticles play a role of heterogeneous nucleation during the foaming process,and with the content of NCC increasing,the volume expansion rate increase and the cell structure is more intensive. The use of PEG show a small influence on the volume expansion rate and cell morphology, but the cells tend to be more homogeneous with the increasing of PEG loading. When foaming temperature is 100℃and soaking time is 4 h,ideal porous foam material can be obtained with cell density and diameter being 3×1010 cell/cm3,5 μm respectively.
Enhancing Foamability and Flame‐retardancy of Polylactic Acid Bead Foams Through Inter‐beads Bulk Polymerization and Continuous Phase Dispersion of LDHs

Wei Liu,Xian Wu,Jigui Zhu,Xiaocheng Chen,Shan Liu,Yang Li

DOI: https://doi.org/10.1002/pol.20240251

IF: 3.046

2024-01-01

Journal of Polymer Science

Abstract:Poly (lactic acid) (PLA) bead foam has a promising application because of its renewable and naturally degradable nature. However, its processing is greatly limited by inherent shortcomings such as the complex polycrystals‐inducing strategy. Herein, we developed a strategy of bulk polymerization reaction of polyvinyl acetate (PVAc) to sinter PLA beads to prepare EPLA foams accompanied by supercritical CO2 foaming technology. In order to enhance the sintering behavior and flame‐retardancy of EPLA foams, two‐dimensional nanolayered double hydroxides (LDHs) were introduced and dispersed in the continuous phase of the sintering layers. The formation of unique dispersion of LDHs and sintering structure of PVAc generated substantial increase in the crystallinity, melt elasticity, and sintering strength of EPLA foams, which facilitated the growth and stabilization of cells. Thus, the cell‐density and expansion ratio could be increased to 8.62 × 106 cell/cm3 to 9.31‐fold, respectively. Moreover, the mechanical properties of the EPLA foams were improved. The tensile strength and the compression strength increased to 2.96 and 62.5 MPa. Additionally, with adding 7 wt.% LDH, the EPLA foam reached UL‐94 V‐0 rating with high limiting oxygen index value of 29.1% and char residue of 20.4%. This study provides a novel strategy for the preparation of flame‐retardant EPLA foams with low density, three dimensional complex shapes, as well as excellent mechanical properties.
Apoptosis pathway signature for prediction of treatment response and clinical outcome in childhood high risk B-Precursor acute lymphoblastic leukemia.

Ya‐Hsuan Chang,Yung‐Li Yang,Chung-Ming Chen,Hsuan-Yu Chen

2015-04-15

American journal of cancer research

Abstract:The most common cancer in children is acute lymphoblastic leukemia (ALL) and it had high cure rate, especially for B-precursor ALL. However, relapse due to drug resistance and overdose treatment reach the limitations in patient managements. In this study, integration of gene expression microarray data, logistic regression, analysis of microarray (SAM) method, and gene set analysis were performed to discover treatment response associated pathway-based signatures in the original cohort. Results showed that 3772 probes were significantly associated with treatment response. After pathway analysis, only apoptosis pathway had significant association with treatment response. Apoptosis pathway signature (APS) derived from 15 significantly expressed genes had 88% accuracy for treatment response prediction. The APS was further validated in two independent cohorts. Results also showed that APS was significantly associated with induction failure time (adjusted hazard ratio [HR] = 1.60, 95% confidence interval [CI] = [1.13, 2.27]) in the first cohort and significantly associated with event-free survival (adjusted HR = 1.56, 95% CI = [1.13, 2.16]) or overall survival in the second cohort (adjusted HR = 1.74, 95% CI = [1.24, 2.45]). APS not only can predict clinical outcome, but also provide molecular guidance of patient management.
Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Dongdong Li,Baoqing Shentu,Zhixue Weng

DOI: https://doi.org/10.1080/00222348.2011.557617

2011-01-01

Abstract:Polylactide (PLA)/poly(ethylene-co-octene) (POE) blends containing ethylene-glycidyl methacrylate copolymer (EGMA) as a compatibilizer were prepared by melt blending. An immiscible, two-phase structure with POE dispersed in the PLA matrix was observed by scanning electron microscopy. It was found that the POE particle size was significantly decreased by the addition of EGMA, and the POE particle size and distribution decreased with the increase of the compatibilizer content up to 2% EGMA, beyond which the POE particle size and distribution remained unchanged. The reactions between the epoxy groups of EGMA and carboxylic or hydroxyl groups of PLA were elucidated by the Fourier transform infrared spectroscopy. Rheological results showed that the G'(omega), G "(omega), and complex viscosity of PLA/POE blends significantly increased at low frequencies with the addition of EGMA. The failure mode changed from brittle fracture of the neat PLA to ductile fracture of the PLA/POE blends.
The synergistic effect of polytetrafluoroethylene in-situ fibrillation and dibenzoyl sebacate hydrazide on the crystallization and foaming behavior of poly (lactic acid)

Yujing Tang,Zhuolun Li,Shihong Chen,Xiangdong Wang

DOI: https://doi.org/10.1016/j.ijbiomac.2022.09.032

2022-11-30

Abstract:The fully degradable poly (lactic acid) foam with green environmental protection characteristics can alleviate the shortage of petroleum resources caused by the application of plastics. However, due to the inherent low melt strength and slow crystallization rate of linear PLA. It is difficult to obtain PLA microcellular foam with good morphology. In order to obtain PLA microcellular foam with ultra-high expansion ratio and small cell size, PTFE (polytetrafluoroethylene) nanofibers with excellent CO2 adsorption rate were introduced. Self-assembled nucleator TMC-300(dibenzoyl sebacate hydrazide) was also introduced to blend with PLA to obtain small-sized cells. The results show that the PTFE entanglement network as a self-assembled template can effectively improve the early crystallization nucleation efficiency and increase the crystallinity of branched PLA (CBPLA)/TMC by 7 %. The microcellular foam with PTFE content of 0.5 wt% (CBPLA/TMC/PTFE 0.5) was successfully prepared by physical foaming agent, which had the lowest cell size (8.7 μm) And high expansion ratio (1200 %).
Investigation of the Effect of Hybrid Nanofiller on the Mechanical Performance and Surface Properties of Bio-Based Polylactic Acid/Polyolefin Elastomer (PLA/POE) Blend

Nariman Rajabifar,Amir Rostami

DOI: https://doi.org/10.3390/polym15122708

IF: 5

2023-06-17

Polymers

Abstract:Polylactic acid has stood out among bio-based polymers for its usage in the food packaging industry and biomedical fields. Through the melt mixing process, the toughened poly(lactic) acid (PLA) was prepared with polyolefin elastomer (POE), incorporated via various ratios of nanoclay and a fixed amount of nanosilver particles (AgNPs). The correlation between the compatibility and morphology, mechanical properties, and surface roughness of samples with nanoclay was studied. The calculated surface tension and melt rheology confirmed the interfacial interaction demonstrated by droplet size, impact strength, and elongation at break. Each blend sample exhibited matrix-dispersed droplets, and the size of POE droplets steadily dropped with increasing nanoclay content, corresponding to the enhanced thermodynamic affinity between PLA and POE. Scanning electron microscopy (SEM) acknowledged that the inclusion of nanoclay in the PLA/POE blend ameliorated the mechanical performance by preferable localization in the interface of used components. The optimum value of elongation at break was acquired at about 32.44%, where the incorporation of 1 wt.% nanoclay led, respectively, to 171.4% and 24% enhancement rather than the PLA/POE blend with the composition of 80/20 and the virgin PLA. Similarly, the impact strength reached 3.46 ± 0.18 kJ m−1 as the highest obtained amount, showing the proximity of 23% progress to the unfilled PLA/POE blend. Surface analysis indicated that adding nanoclay caused the augment of surface roughness from 23.78 ± 5.80 μm in the unfilled PLA/POE blend to 57.65 ± 18.2 μm in PLA/POE contained 3 wt.% nanoclay. Rheological measurements implied that organoclay resulted in the strengthening of melt viscosity as well as the rheological parameters such as storage modulus and loss modulus. Han plot further showed that the storage modulus is always higher than the loss modulus in all prepared PLA/POE nanocomposite samples, corresponding to the restriction of polymer chains mobility induced by the formation of strong molecular interaction between nanofillers and polymer chains.

polymer science
Extrusion foaming of Poly(lactic acid)/Rice straw composites: Opposing effects of eco-friendly physical/chemical treatment and compatibilization methods

Aidin Jafari,Reza Asheghi-Oskooee,Farkhondeh Hemmati,Jamshid Mohammadi-Roshandeh

DOI: https://doi.org/10.1177/00219983241262878

IF: 3.191

2024-06-12

Journal of Composite Materials

Abstract:Journal of Composite Materials, Ahead of Print. In this study, the effects of two environmentally-friendly pulping methods along with two different reactive compatibilization methods on the foamability of poly (lactic acid) (PLA)/rice straw (RS) biocomposites have been investigated. RS as an annually renewable agricultural waste is low-cost and available. Melt-compounding and melt-foaming processes were performed through a twin-screw extrusion processing. The correlations between processing and microstructure were studied. The findings show that the RS pulping with sodium bicarbonate (SB) solution leads to the lignocellulosic particles with a porous structure. The structure causes the filler/matrix mechanical engagement and improves the interfacial adhesion and rheological properties, hence forming smaller cells with the narrowest cell size distribution. In contrast, applying ultrasound waves on the RS pulp brings the particles to very smooth surfaces. These surfaces have the highest activity at the cell nucleation stage and considerably increase the foam's cell density. The reactive compatibilizers based on epoxy and maleic anhydride groups show opposing effects on the biocomposite microstructure, depending on the RS pulp type. The use of the reactive compatibilizers in the PLA/RS pulp treated with SB led to lighter foams with larger cells and higher cell densities and void fractions. Whereas the incorporation of the compatibilizers into the biocomposites containing RS pulp treated with SB and ultrasonic waves resulted in noticeably lower cell density and larger foam density. The extruded biocomposite foams with closed-cell microstructure can be used in insulation and packaging applications.

materials science, composites
Environmentally-friendly solvent pulping and grafting strategies for better foamability of poly(lactic acid)/agricultural waste biocomposites

Pedram Bahrami,Parisa Morsali,Danial Abbasi,Farkhondeh Hemmati,Jamshid Mohammadi-Roshandeh

DOI: https://doi.org/10.1177/07316844241264310

IF: 3.1

2024-06-24

Journal of Reinforced Plastics and Composites

Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. In this study, the foamability of poly (lactic acid) (PLA) through a continuous extrusion process was enhanced by using an agricultural waste, environmentally friendly pulping methods, and reactive compatibilization of the lignocellulosic filler with matrix in the extrusion flow field. Both applied solvent-pulping methods by using chemicals with low safety and toxicity risks were considerably successful in purifying the micron-sized cellulosic fibers of rice straw (RS). The interface of PLA matrix with RS pulp fibers was modified by applying reactive compatibilizers containing maleic anhydride (MA) and epoxy functional groups. Both compatibilizers had the ability to simultaneously react with the hydroxyl groups of RS pulp fibers and end groups of PLA chains during the melt-compounding process. As a result of RS pulping and PLA/RS pulp compatibilizing reactions, the processability of PLA in an extrusion foaming process was substantially enhanced, in a way that the void fraction and cell density of PLA foam increased more than seven and two times, respectively. The extruded lightweight all-green biocomposite foams can be applied in construction and packaging applications.

materials science, composites,polymer science
A Facile and Clean Strategy to Manufacture Functional Polylactic acid Bead Foams

Wei Liu,Xian Wu,Chun Zhang,Shikui Jia

DOI: https://doi.org/10.1016/j.mtcomm.2023.106828

IF: 3.8

2023-08-09

Materials Today Communications

Abstract:Expanded poly (lactic acid) (EPLA) is a promising bio-material with ultra-low density, thermal insulation, cushioning properties, as well as the ability to be fabricated products in complex shapes. However, the time consuming of inducing double melt peaks of PLA and the complex two-steps process of steam-sintering assisted supercritical CO 2 foaming is inevitable since PLA belongs crystalline polymer. To develop a facile and simple method to produce EPLA foams with functions, we used the bulk polymerization of liquid reactants to form a sintering layer between PLA beads. Meanwhile, carbon nanotubes (CNT) were synchronously introduced and distributed in the sintering layer. And a unique EPLA foam with functional sintering layer was produced using supercritical CO 2 foaming technology. The reported method could prepare EPLA foam with high expansion ratio of 8.5 times and high cell density of 8.25 × 10 8 cell/cm 3 . Compared with other methods, the novel EPLA foams exhibited excellent tensile strength and compressive strength, superior electrical conductivity of 0.12 S/m, electromagnetic shielding ability of 99% in the X-band at CNT content of 2.68 wt .%, as well as sensitive and accurate stress-sensing function. It facilitates the development of novel manufacturing technology and the expansion of applications fields of EPLA foam.

materials science, multidisciplinary
Multi-Response Optimization and Cell Structure-Property Relationships of Polylactide (PLA) Foams

Yusuf Arya Yudanto,Atitsa Petchsuk,Pakorn Opaprakasit

DOI: https://doi.org/10.14416/j.asep.2024.06.011

2024-06-27

Applied Science and Engineering Progress

Abstract:The renewability and ease of processing of polylactide (PLA) make it ideal for disposable foam products. However, controlling the foam structure is challenging due to its low melt strength and crystallization ability, which can result in cell rupture-prone and excessively large cells, necessitating a comprehensive understanding of the influences of foaming parameters (temperature, pressure, and time) on cell structures and properties to unlock PLA’s full potential. This study optimizes the fabrication of PLA foams using solid-state batch foaming under supercritical CO2 conditions by employing a central composite design of response surface methodology. Single-parameter investigations reveal that higher foaming temperature, increased pressure, and longer foaming time increase the apparent density due to reduced polymer viscosity, pressure-dependent gas entrapment, and enhanced gas diffusion, leading to faster cell nucleation and cell formation. The compressive properties depend on stress-strain behavior and cell morphology, influenced by the cell shape and wall thickness. Thicker cell walls delay cell buckling and improve compression resistance. Higher sphericality evenly distributes compressive stress across cell surfaces, enhancing the foam’s resilience against localized collapse. Multi-response optimization successfully fabricated lightweight PLA foam (0.134 g/cc apparent density) with enhanced compressive modulus (1.955 MPa at 50% strain) and controlled cell morphology (average cell size of 21.055 μm and cell density of 52.385 × 105 cells/cm3) at optimized foaming conditions (180 °C, 165 bar, and 2.3 h). The PLA foams have potential as a reusable and degradable absorbent for liquids and oils, but there are challenges in scaling production.
Experimental investigation on mechanical properties of nanocomposites based on poly lactic acid/ polyolefin elastomer reinforced with multi-walled carbon nanotubes, and graphene nanoplatelets

Sajjad Daneshpayeh,Faramarz Ashenai Ghasemi,Ismail Ghasemi

DOI: https://doi.org/10.1177/09673911211060943

2022-01-01

Polymers and Polymer Composites

Abstract:The mechanical properties of nanocomposites based on poly lactic acid/polyolefin elastomer (PLA/POE) were investigated. The compounds were made using an internal mixer. POE in two levels at 10–20 wt.% and nano fillers, including multi-walled carbon nanotubes (MWCNT) and graphene nano-platelets (GnPs) in 1, 2, and 3 wt.% levels, were added to the PLA. Impact and tensile tests were conducted to extract the impact and tensile properties, respectively. The dispersion quality of the fillers was also studied by using field-emission scanning electron microscopy (FESEM) images. The FESEM images demonstrated that the MWCNT at all levels were well distributed in different orientations, while the GnPs accumulated into the PLA/POE matrix. The simultaneous presence of nano fillers was dispersed with high quality in the matrix only in low loading. The tensile test results showed that by increasing the nano fillers individually and in a hybrid form in the presence of different loadings of POE, Young’s modulus and T-strength were improved, but impact strength and deformation at break were decreased. The addition of the POE to the PLA matrix significantly increased the impact strength and deformation at break by 128% and 75%, respectively, and the presence of POE reduced Young’s modulus and T-strength of the PLA matrix.

materials science, composites, characterization & testing,polymer science
Preparation and Supercritical CO2 Foaming of Modified Nanocrystalline Cellulose Reinforced Polylactic Acid Bionanocomposites

Dan Chen,Ping Zhang,Jiajun Wang,De Gao

DOI: https://doi.org/10.1155/2022/2805670

IF: 2.0981

2022-01-01

Advances in Materials Science and Engineering

Abstract:The solution casting method was used to prepare polylactic acid/modified nanocrystalline cellulose (PLA/mNCC) composites, and the effects of the mNCC content on the morphology, thermal characteristics, and rheological properties of the PLA nanocomposite were examined. The PLA microcellular foaming nanocomposite was prepared using supercritical CO2 foaming. Furthermore, the foaming conditions were optimized, and the effect of NCC surface modification, as well as the content and interfacial force of nanoparticles, on the foaming efficiency and cell pattern of composites was examined. The results suggested that a sufficient number of nanoparticles increased the nucleation site for foaming and played a vital role in heterogeneous nucleation in the foaming system. An ideal microcellular foaming material with an average cell diameter of 6.97 μm and a cell density of 6.05 × 109 cells/cm3 was prepared when the foaming temperature was 110°C, the foaming pressure was 18 MPa, the incubation period was 2 h, and the mNCC content was 6%.
Investigating the Effects of Temperature, Azodicarbonamide, Boron Nitride, and Multilayer Film/Foam Coextrusion on the Properties of a Poly(Hydroxyalkanoate)/Poly(Lactic acid) Blend

Yousefi, Amy M.

DOI: https://doi.org/10.1007/s10924-024-03310-9

IF: 4.705

2024-08-24

Journal of Polymers and the Environment

Abstract:Poly(hydroxyalkanoates) (PHAs) are emerging as sustainable materials in packaging and medical device industries. Nevertheless, the high cost and the need to improve the mechanical properties have limited their widespread use. Blending with other bio-based polymers, such as poly(lactic acid) (PLA), has been proposed in previous studies. This study investigates the effects of temperature, azodicarbonamide (AZ, foaming agent), boron nitride (BN, filler), and multilayer film/foam coextrusion on the properties of a blend containing an amorphous PHA and PLA. The effect of twin-screw micro-compounder temperature (185 °C & 205 °C) and BN concentrations of 1, 2, 3, 5, and 10 wt% (185 °C) on the properties of the PHA/PLA blend were investigated using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and tensile testing. Design of experiments (DoE) was used to find the optimal concentrations of AZ and BN (205 °C) using JMP® software. The response surface analysis predicted an optimal design based on the target response levels (modulus, tensile strength, strain at break, and toughness). This formulation was prepared and characterized using DSC, TGA, tensile, and melt flow index (MFI) measurements. Finally, this formulation was processed via film/foam coextrusion and examined using scanning electron microscopy (SEM) and density measurements. This study demonstrated that AZ and BN can be used to manipulate the mechanical properties and crystallinity of PHA/PLA blends, while reducing the overall material cost via density reduction (20–21% for the optimal formulation). Furthermore, reducing the concentration of AZ using the I-optimal design in this study could alleviate the toxicity concerns for food packaging.

engineering, environmental,polymer science

Value of PET and PET/CT in the diagnostics of prostate and penile cancer.

Extrusion Foaming Of Lightweight Polystyrene Composite Foams With Controllable Cellular Structure For Sound Absorption Application

Fabrication of biodegradable poly (lactic acid)/carbon nanotube nanocomposite foams: Significant improvement on rheological property and foamability

Rheological behavior, crystallization properties, and foaming performance of chain-extended poly (lactic acid) by functionalized epoxy

Foamability of all‐green polylactide/rice straw pulp biocomposites through continuous extrusion process: Effects of pulping and reactive compatibilization

Modified standard polylactic acid (PLA) for extrusion foaming

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Extruded polylactide bead foams using anhydrous supercritical CO2 extrusion foaming

Study on Foaming Properties of PLA/NCC Microcellular Foam Materials

Enhancing Foamability and Flame‐retardancy of Polylactic Acid Bead Foams Through Inter‐beads Bulk Polymerization and Continuous Phase Dispersion of LDHs

Apoptosis pathway signature for prediction of treatment response and clinical outcome in childhood high risk B-Precursor acute lymphoblastic leukemia.

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

The synergistic effect of polytetrafluoroethylene in-situ fibrillation and dibenzoyl sebacate hydrazide on the crystallization and foaming behavior of poly (lactic acid)

Investigation of the Effect of Hybrid Nanofiller on the Mechanical Performance and Surface Properties of Bio-Based Polylactic Acid/Polyolefin Elastomer (PLA/POE) Blend

Extrusion foaming of Poly(lactic acid)/Rice straw composites: Opposing effects of eco-friendly physical/chemical treatment and compatibilization methods

Environmentally-friendly solvent pulping and grafting strategies for better foamability of poly(lactic acid)/agricultural waste biocomposites

A Facile and Clean Strategy to Manufacture Functional Polylactic acid Bead Foams

Multi-Response Optimization and Cell Structure-Property Relationships of Polylactide (PLA) Foams

Experimental investigation on mechanical properties of nanocomposites based on poly lactic acid/ polyolefin elastomer reinforced with multi-walled carbon nanotubes, and graphene nanoplatelets

Preparation and Supercritical CO2 Foaming of Modified Nanocrystalline Cellulose Reinforced Polylactic Acid Bionanocomposites

Investigating the Effects of Temperature, Azodicarbonamide, Boron Nitride, and Multilayer Film/Foam Coextrusion on the Properties of a Poly(Hydroxyalkanoate)/Poly(Lactic acid) Blend