Chiasmatic arachnoiditis. A case report and review.

J. Coyle

DOI: https://doi.org/10.1016/0002-9394(69)94083-5

1969-08-01

Abstract:

What problem does this paper attempt to address?

Anaerobic Digestion Performance of Concentrated Municipal Sewage by Forward Osmosis Membrane: Focus on the Impact of Salt and Ammonia Nitrogen.

Yue Gao,Zhou Fang,Peng Liang,Xiaoyuan Zhang,Yong Qiu,Katsuki Kimura,Xia Huang

DOI: https://doi.org/10.1016/j.biortech.2019.01.016

IF: 11.4

2019-01-01

Bioresource Technology

Abstract:Sewage can become a valuable source if its treatment is re-oriented. Forward osmosis (FO) is an effective pretreatment for concentrating solutions. A laboratory-scale anaerobic digestion (AD) bioreactor was setup for the treatment of concentrated real sewage by FO membrane to investigate the removal of chemical oxygen demand (COD) and biogas production. Inhibitory batch tests were carried out for the impact of NaCl and NH4+-N. Results showed that the concentrated sewage could be purified with 80% COD removal, and energy recovery could be achieved. But the process was inhibited. The results of inhibitory batch test showed that (i) when the NH4+-N concentration was lower (< 200 mg/L), the biogas production was promoted, when it went high, the inhibition appeared; (ii) single existence of NaCl had negative influence on methane production; (iii) the inhibition was more severe with co-existence of NaCl and NH4+-N. The AD performance could be recovered via sludge acclimation.
Probing The Key Foulants And Membrane Fouling Under Increasing Salinity In Anaerobic Osmotic Membrane Bioreactors For Low-Strength Wastewater Treatment

Liven Wenhui Lee,Xianzheng Zhu,Ziwei Liu,Yue Gao,Cheng Chen,Xia Huang

DOI: https://doi.org/10.1016/j.cej.2020.127450

IF: 15.1

2021-01-01

Chemical Engineering Journal

Abstract:Anaerobic osmotic membrane bioreactors (AnOMBRs) have attracted much attention in recent years due to their ability to produce high-quality effluent with low energy demand. Here, the performance of a thin film composite (TFC) forward osmosis (FO) membrane in an AnOMBR system is evaluated, and the key membrane foulants are examined by analyzing the characteristics of the mixed liquor and the fouling layer. As the experiment progressed, the water flux declined due to membrane fouling and salt accumulation in the bioreactor, and reached approximately 3.5 LMH by the end of each operating cycle where membrane cleaning was adopted. The conductivity increased from 3.3 mS/cm to 23.6 mS/cm over the 28-day treatment. The contaminant rejection rates of total organic carbon, total phosphorous and ammonia-nitrogen were more than 93%, 98% and 60%, respectively. Results also suggested that extracellular polymeric substances (EPS) was the major contributor to membrane fouling, and the increase of EPS in the mixed liquor with salinity was primarily composed of polysaccharides. The comprehensive characterization of the fouling layer via X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and confocal laser scanning microcopy (CLSM) revealed the coexistence of biofouling and organic fouling. The CLSM images further demonstrated the prevalence of ? polysaccharides, proteins and microorganisms on the fouled TFC FO membrane surface. In addition, the flow cytometric analysis indicated that the foulant sample was ?bacterial viable?, the large number of bacteria in suspension (96.61% live cells) maybe corresponded to the high EPS content in the bulk mixed liquor.
Direct Concentration of Municipal Sewage by Forward Osmosis and Membrane Fouling Behavior

Yue Gao,Zhou Fang,Peng Liang,Xia Huang

DOI: https://doi.org/10.1016/j.biortech.2017.09.145

IF: 11.4

2018-01-01

Bioresource Technology

Abstract:Forward osmosis (FO) draws attention due to its advantages compares to traditional pressure-driven membrane processes. In this study, a FO membrane concentrating system was built for sewage concentration to investigate membrane rejection, concentrating effect, membrane fouling behavior. Sewage could be concentrated to 1/10 original volume by FO membrane, while pollutants concentrating multiple could not reach 10. The FO membrane had excellent rejecting effect, with effluent COD, ammonia nitrogen, total nitrogen, total phosphorus concentration of 18, 2.5, 2.8, 0.4 mg/L, respectively. The FO membrane flux was mainly associated with the draw solution (DS) concentration, which increased with DS concentration but more severe membrane fouling engendered in the meantime. Scanning electronic microscope and fourier transform infrared spectroscopy analysis indicated the formation and constitution of the fouling layer, which included humic acid, protein, and polysaccharide. After concentration, fouled FO membrane was remitted by physical and chemical cleaning, with recovery of 90% and 96%.
Determination of the critical draw solution concentration for anaerobic microfiltration osmotic membrane bioreactors

Sumeyye Hasanoglu,Ilknur Yalcin Guney,Ilda Vergili,Gulsum Yilmaz,Yasemin Kaya,Coskun Aydiner,Z. Beril Gönder

DOI: https://doi.org/10.1016/j.cej.2024.148935

IF: 15.1

2024-02-01

Chemical Engineering Journal

Abstract:Anaerobic microfiltration osmotic membrane bioreactors (AnMF-OMBRs) have the advantages of resource recovery such as energy, water, and nutrients, but they have some drawbacks of low flux and severe membrane fouling. The concentration of draw solution (DS) is effective on the flux and fouling of FO membrane, and microbial inhibition. The aim of this study is to determine the critical DS concentration in AnMF-OMBR and up-flow anaerobic sludge blanket microfiltration osmotic membrane bioreactor (UASB MF-OMBR) systems operated with DS concentrations of 0.47, 1, and 1.5 M. The analytical hierarchical process (AHP) was applied to determine the critical DS concentration considering the criteria of forward osmosis (FO) performance, anaerobic performance, water recovery, microbial inhibition and operation time. The results demonstrated that the DS concentration of 0.47 M showed a better system performance, by causing less membrane fouling and microbial inhibition than that of the 1 and 1.5 M, and higher methane yield was obtained with 0.47 M in both bioreactors. The membrane autopsy analyses verified that the membrane fouling was severe with increasing DS concentration. Microbial community structure was affected by salinity build-up, high free ammonia (FA), and low organic loading rate (OLR). The relative abundance of Synergistota, a syntrophic acetate oxidizer, showed a parallel trend with Methanobacterium, a hydrogenotrophic methanogen in the conditions of high FA and salinity build-up due to the FO operation. Consequently, the critical DS concentration was determined as 0.47 M MgCl2.

engineering, chemical, environmental
Black odorous water concentrating by forward osmosis (FO) with aquaporin biomimetic membranes: Pollutants concentrating and membrane fouling characteristics

Yong Zhang,Kai-Tong Wang,Wei-Li Jiang,Jia-Ying He,Hong Wang,Bing Li,Ming Gao

DOI: https://doi.org/10.1016/j.cej.2020.125938

IF: 15.1

2020-11-01

Chemical Engineering Journal

Abstract:This study aimed to investigate pollutant concentration and membrane fouling characteristics of a forward osmosis (FO) process using aquaporin biomimetic membrane (ABM) for concentrating black odorous water. The membrane cells were operated in active layer facing feed solution (ALFS) mode with 2 M NaCl solution as the draw solution. The system was continuously performed for 64 batch cycles, and each cycle duration was 24 h. At the end of each cycle, physical cleaning with deionized water was employed as the membrane recovery strategy. The results showed that the rejection ratios of chemical oxygen demand (COD), total phosphorus (TP) and nitrate (NO3--N) could reached 97.2%, 98.0%, and 85.0%, respectively, while most NH4+-N penetrated into the draw solution due to cation exchange. The total nitrogen (TN) rejection ratio was largely dependent upon the NH4+-N/TN ratio. At high NH4+-N/TN ratio, the successions of ammonia oxidizing bacteria (AOB) communities enriched in the biofouling layer in different experimental stages would affect the transformation degree of NH4+-N, and thus lead to much fluctuations of TN rejection. The average initial water flux reached 9.84 L/(m2·h), and the average water flux of each cycle kept stable especially in the later stage of the experiment. In the biofouling layer, polysaccharides enhanced while proteins decreased in the later period. P, Mn, Fe and Na also accumulated on the surface. Norank_f__Reyranellaceae, Erythrobacter, SM1A02, Pirellula, and Hydrogenophaga were the predominant genera enriched in the fouling layer, which would lead to complex pollutants transformations, especially nitrogen transformation, during the FO process.

engineering, chemical, environmental
Induction chemotherapy with gemcitabine and cisplatin in paranasal sinus tumours.

R. Hussain,A. Jamshed,M. Bilal,K. Shehzad,R. Azhar,M. A. Shah,S. Hameed,M. Arif,Z. Faruqui

DOI: https://doi.org/10.1200/jco.2006.24.18_suppl.15542

IF: 45.3

2006-06-20

Journal of Clinical Oncology

Abstract:15542 Background: There is no standard treatment for locally advanced carcinoma of paranasal sinuses. Induction chemotherapy is frequently used to down stage the disease. Surgery, radiotherapy and chemoradiation are all in use to treat the primary following neoadjuvant chemotherapy treatment. Cisplatin and gemcitabine are active agents in head and neck cancers. We evaluated the response of induction chemotherapy with cisplatin and gemcitabine in carcinoma of the paranasal sinuses. METHODS Between August 2005-November 2005, 5 patients with locally advanced carcinoma paranasal sinuses received induction chemotherapy at Shaukat Khanum Cancer Hospital and Research Centre. There were three males and two females, 19 to 65 (median 45) years of age. Three patients had maxillary and 2 patients had ethmoid sinus tumors. Four patients had Stage IVa and 1 patient had Stage IVb disease. All patients had biopsy proven carcinoma. Histologically the tumour was adenocarcinoma in 1 patient and squamous cell carcinoma in 4 patients. Four patients received 2 cycles and 1 patient received 1 cycle of cisplatin 75 mg/m2 day 1 and gemcitabine 1000 mg/m2 day 1 and 8 (repeat day 22) before radical treatment. Response was assessed in all patients with pre and post induction chemotherapy with CT or MRI scan. RESULTS Overall response rate was 60%. Complete response was seen in one patient and over 50% tumor regression in 2 patients. Disease remained unchanged (no response) in 1 patient. One patient progressed following one cycle and did not receive the second cycle of chemotherapy treatment. The treatment was well tolerated and no grade III or IV toxicity was seen. CONCLUSIONS The combination of gemcitabine and cisplatin in this schedule has low toxicity and significant activity in patients with locally advanced paranasal sinus tumors and is worthy of further study. No significant financial relationships to disclose.
Aerobic SMBR/reverse Osmosis System Enhanced by Fenton Oxidation for Advanced Treatment of Old Municipal Landfill Leachate

Guoliang Zhang,Lei Qin,Qin Meng,Zheng Fan,Dexin Wu

DOI: https://doi.org/10.1016/j.biortech.2013.05.006

IF: 11.4

2013-01-01

Bioresource Technology

Abstract:A novel combined process of Fenton oxidation, submerged membrane bioreactor (SMBR) and reverse osmosis (RO) was applied as an appropriate option for old municipal landfill leachate treatment. Fenton process was designed to intensively solve the problem of non-biodegradable organic pollutant removal and low biodegradability of leachate, although the removal of ammonia-nitrogen was similar to 10%. After SMBR treatment, it not only presented a higher removal efficiency of organics, but also exhibited high ammonia-nitrogen removal of 80% on average. The variation of extracellular polymeric substance (EPS) content, zeta potential, and particle size of flocs after Fenton effluent continually fed in SMBR was found to be benefit for alleviating membrane fouling. Finally, three kinds of RO membranes (RE. CPA, and BW) were applied to treat SMBR effluents and successfully met wastewater re-utilization requirement. Compared with simple RO process, the troublesome membrane fouling can be effectively reduced in the combined process. (C) 2013 Elsevier Ltd. All rights reserved.
Effects of Critical Operation and Cleaning Parameters on Performances and Economic Benefits of Biogas Slurry Concentration by Forward Osmosis Membrane

Bangxi Zhang,Tianhong Fu,Qinyu Zhang,Xiaomin Wang,Ling Tang,Quanquan Wei,Yun Li,Yutao Peng

DOI: https://doi.org/10.3390/membranes13030288

IF: 4.562

2023-03-01

Membranes

Abstract:Forward osmosis membrane technology (FO) shows potential application prospects in biogas slurry concentration, which is conducive to promoting the sustainable development of biogas projects. However, at present, the key influencing factors of membrane concentration using FO are not well understood. Therefore, this study analyzed the influence of draw solution concentration, pH, temperature and cross-flow velocity on the concentration efficiency of FO membrane, and optimized the operation parameters of FO membrane. The results showed that the concentration effect of the NaCl draw solution at pH 5 or 9 was better than that at pH 7. The order of factor influencing the water flux was as follows: draw liquid concentration > cross-flow velocity > operating temperature. The optimal combination obtained by orthogonal analysis was under 45 °C, with a cross-flow velocity of 1 L/min and the use of 1.5 mol/L NaCl as draw solution. The results of the membrane cleaning implied that the recovery rate of the fouled membrane after acid–base cleaning is significantly higher (88%) than other cleaning solutions. This research offers a scientific reference for applying positive osmosis technology to re-utilize biogas slurry resources.

engineering, chemical,materials science, multidisciplinary,polymer science,chemistry, physical
Lower bounds on blow up solutions of the three-dimensional Navier–Stokes equations in homogeneous Sobolev spaces

James C. Robinson,W. Sadowski,Ricardo P. Silva

DOI: https://doi.org/10.1063/1.4762841

2012-11-13

Abstract:Suppose that u(t) is a solution of the three-dimensional Navier–Stokes equations, either on the whole space or with periodic boundary conditions, that has a singularity at time T. In this paper we show that the norm of u(T − t) in the homogeneous Sobolev space Hs must be bounded below by cst−(2s−1)/4 for 1/2 5/2. (The result for 1/2 < s < 3/2 follows from well-known lower bounds on blowup in Lp spaces.) We show in particular that the local existence time in Hs(R3) depends only on the Hs-norm for 1/2 < s < 5/2, s ≠ 3/2.
Efficient organic enrichment from sludge filtrate via a forward osmosis membrane process

Jiang Chang,Haoran Qiu,Jiawei Wang,Rijia Lin,Byron Villacorta Hernandez,Chunmiao Ji,Guoliang Liu,Xuan Zhao,Lei Ge

DOI: https://doi.org/10.1016/j.jece.2020.104042

IF: 7.7

2020-08-01

Journal of Environmental Chemical Engineering

Abstract:Anaerobically digested sludge filtrate after thermal hydrolysis pretreatment (THP-AD) requires large plant and operational costs for post-treatment and re-utilization. This paper reports the innovative forward osmosis (FO) membrane process to enrich organic matter from such a digested sludge filtrate. The proposed membrane separation process can reduce the operational load and environmental dependence of waste sewage treatment plants and may provide a new way for the treatment of THP-AD sludge filtrate. In this study, a cost-effective draw NaCl solution was selected for the FO process. The sensitivity of membrane operational conditions including membrane orientation, system temperature, system flow rate and concentrations of draw solution was investigated and correlated with the FO processing performance. FO mode is a clever choice to reduce the deposition of pollutants on the membrane's surface, and improve the recovery performance of the membrane. The permeation flux of the THP-AD sludge digestion system decreased more rapidly due to the membrane pollution as well as to the decreasing of driving force caused by the dilution of the draw solution and the concentration of the feed solution. The concentration factor of digested sludge filtrate after FO process was more than five, and the rejection rates of organic and inorganic matter were above 92.5%. The membrane permeability recovery after the offline washing reached up to 98.4% and showed high efficiency at removing membrane fouling substances and at reactivating the membrane. The proposed FO process has potential as an alternative and practical method for treating and utilizing intractable sludge filtrates, conducive to the development of sustainable wastewater plants.

engineering, chemical, environmental
Deciphering mono/multivalent draw solute-induced microbial ecology and membrane fouling in anaerobic osmotic membrane bioreactor

Xianzheng Zhu,Liven Wenhui Lee,Guangqing Song,Xian Zhang,Yue Gao,Guang Yang,Shuai Luo,Xia Huang

DOI: https://doi.org/10.1016/j.watres.2021.117869

IF: 12.8

2022-02-01

Water Research

Abstract:Anaerobic osmotic membrane bioreactor (AnOMBR) attracted attention due to high quality effluent production with low energy demand, and draw solute has significant effect on the system performance. However, the mutual relationship between draw solute-induced salinity accumulation and microbial community had many unknown questions to be solved. This study purpose was to construct two AnOMBR to compare the impact of draw solutes of NaCl and MgCl2 on the dynamic change of microbial ecology and membrane fouling. The result indicated that the draw solute of MgCl2 caused less salinity and more membrane biofouling than that of the draw solute NaCl. Multiple microbiological analysis methods were applied to discover keystone species related to the conductivity change and membrane fouling, especially for the MgCl2-AnOMBR system. It was found that draw solute NaCl could benefit the growth of Proteobacteria to become the most abundant phylum to affect the membrane fouling, while Mg2+ introduction could stimulate the growth of NS9, Hydrogenphilaceae and Pedosphaeraceae to potentially cause the biofouling. Furthermore, phylogenetic molecular ecological networks (pMENs) deeply analyzed the microbial structure difference under Na+ and Mg2+ introduction, and indicated that the family Lentimicrobiaceae and Candidatus_Kaiserbacteria were the keystone species in NaCl-AnOMBR, while two genus Anaerolinea and SWB02, and two families Saprospiraceae and NS9 were discovered to have key effect in MgCl2-AnOMBR due to their strong extracellular polymeric substances (EPS) production ability for survival of other microorganisms. This study was significant to give microbial targets under the impact of various draw solutes, as the reference for the engineers to further investigate how to improve the microbial structure to enhance AnOMBR performance and inhibit the membrane biofouling.

environmental sciences,engineering, environmental,water resources
Utilization of unrejected ammonium for fouling prevention in a forward osmosis process tested with real primary wastewater from Hong Kong

Paula Jungwon Choi,Xinning Zhang,Di Wu,Ling Li,Am Jang,Alicia Kyoungjin An

DOI: https://doi.org/10.1016/j.desal.2024.117293

IF: 11.211

2024-01-14

Desalination

Abstract:Forward osmosis (FO) process is known to have high rejection towards foulants and ions. However, the polyamide surfaces of FO membranes are usually designed to be negatively charged, which results in low ammonium rejection. This study proposes to utilize the unrejected ammonium in the draw solution (DS) of FO processes by adding OCl − to generate monochloramine, which can diffuse back towards the feed side and prevent. Tests were performed to identify the optimal FO operating conditions, such as DS concentration, crossflow velocity, and flow direction. Optimal conditions were determined to be a DS concentration of 1.0 M, a crossflow velocity of 5.4 cm/s and counter-current flow mode. A 72 h fouling tests were also conducted with real wastewater from the Siu Ho Wan Sewage Treatment Works in Hong Kong as the feed. The existence of monochloramine alleviated membrane fouling. The novelty of this study lies on the fact that the chloramine is generated using the unrejected ammonia, and consequently utilizing the generated chloramine that is reversely diffusing towards the feed to prevent the fouling formation. Findings from this study suggest that the generation of monochloramine from unrejected ammonium ions can lengthen membrane life while endowing self-cleaning abilities that prevent severe fouling.

engineering, chemical,water resources
Osmotic versus conventional membrane bioreactors integrated with reverse osmosis for water reuse: Biological stability, membrane fouling, and contaminant removal

Wenhai Luo,Hop V Phan,Ming Xie,Faisal I Hai,William E Price,Menachem Elimelech,Long D Nghiem

DOI: https://doi.org/10.1016/j.watres.2016.11.036

2017-02-01

Abstract:This study systematically compares the performance of osmotic membrane bioreactor - reverse osmosis (OMBR-RO) and conventional membrane bioreactor - reverse osmosis (MBR-RO) for advanced wastewater treatment and water reuse. Both systems achieved effective removal of bulk organic matter and nutrients, and almost complete removal of all 31 trace organic contaminants investigated. They both could produce high quality water suitable for recycling applications. During OMBR-RO operation, salinity build-up in the bioreactor reduced the water flux and negatively impacted the system biological treatment by altering biomass characteristics and microbial community structure. In addition, the elevated salinity also increased soluble microbial products and extracellular polymeric substances in the mixed liquor, which induced fouling of the forward osmosis (FO) membrane. Nevertheless, microbial analysis indicated that salinity stress resulted in the development of halotolerant bacteria, consequently sustaining biodegradation in the OMBR system. By contrast, biological performance was relatively stable throughout conventional MBR-RO operation. Compared to conventional MBR-RO, the FO process effectively prevented foulants from permeating into the draw solution, thereby significantly reducing fouling of the downstream RO membrane in OMBR-RO operation. Accumulation of organic matter, including humic- and protein-like substances, as well as inorganic salts in the MBR effluent resulted in severe RO membrane fouling in conventional MBR-RO operation.
Performance and membrane fouling behaviors analysis with SVR-LibSVM model in a submerged anaerobic membrane bioreactor treating low-strength domestic sewage

Jianwei Liu,Xinyue Kang,Xinrong Luan,Liutang Gao,Hongyu Tian,Xueli Liu

DOI: https://doi.org/10.1016/j.eti.2020.100844

2020-08-01

Abstract:A submerged anaerobic membrane bioreactor was studied for low concentration domestic sewage treatment over a period of 190 days. The performance and membrane fouling characteristics were investigated and LibSVM model was established to predict COD removal and extracellular polymeric substances' effect on membrane fouling. Average COD removal efficiency ranged from 64.41 to 83.49% during different stages, and the removal efficiency of nitrogen and phosphorus were relatively low. The epsilon-SVR-RBF model can accurately predict the operational performance and membrane fouling of SAnMBR. The optimum OLR range 2.0 to 2.5 kg COD/m3<math>⋅</math>d and membrane fouling mainly manifested both in the sharp increase of <math>Rt</math> and TMP when EPSs>350 mg/L predicted by the model. Physical flushing can alleviate rather than eliminate membrane fouling. Proteins play a vital role in membrane fouling rather than EPSs and polysaccharide in EPSs.

environmental sciences,engineering, environmental,biotechnology & applied microbiology
Direct Membrane Filtration (DMF) of municipal wastewater – A study on the prevention and remediation of fouling

Omer Khalid,Simon Gidstedt,Frank Lipnizki,Gregor Rudolph-Schöpping

DOI: https://doi.org/10.1016/j.jwpe.2024.106235

IF: 7

2024-10-07

Journal of Water Process Engineering

Abstract:Direct membrane filtration (DMF) has gained a lot of attention in recent years because of its potential to treat low-strength and low temperature wastewater, where biological based treatments are inefficient. However, fouling is a major concern which keeps this technique from being more widely used. The main aim of this study was to investigate membrane fouling, its mitigation approaches and the organic/nutrient retention during DMF of municipal wastewater by adjusting operational parameters and pretreating the sewage. In a laboratory-scale setup employing crossflow to mitigate fouling, both ultrafiltration and microfiltration membranes were utilized. Physicochemical pre-treatment of sewage with polyaluminum chloride and polyamide significantly inhibited membrane fouling and improved organics/nutrient retention. Subsequent experiments with physiochemically pre-treated sewage, using microfiltration and ultrafiltration separately, revealed that (i) an increase in crossflow velocity from 1 to 2 m s −1 improved filtration performance by reducing irreversible fouling, (ii) elevating transmembrane pressure from 0.18 to 0.4 bar increased both reversible and irreversible fouling, and (iii) periodic relaxation increased the extent of irreversible fouling, contributing to higher overall fouling in ultrafiltration. When employing DMF for sewage concentration, ultrafiltration demonstrated superior filtration performance and organics retention compared to microfiltration. Furthermore, through pre-precipitation and microsieving (100 μm) followed by DMF with ultrafiltration membranes, a remarkable removal efficiency of 92 % for chemical oxygen demand (COD), 98 % for total phosphorus (TP), and 100 % for total suspended solids (TSS) was achieved. By cleaning the fouled membranes using an alkaline cleaning solution (Ultrasil-10) at 50 °C, combined with a crossflow of 1 m s −1 , the permeability was completely restored. Overall, this study demonstrates that by optimizing operational settings and cleaning conditions, a sustainable DMF process for wastewater treatment with controlled membrane fouling and improved resource recovery can potentially be developed for upscaling. Short abstract This study investigated the effectiveness of direct membrane filtration for municipal wastewater treatment. It was found that physicochemical pre-treatment with polyaluminum chloride and polyamide significantly reduced membrane fouling and improved nutrient retention. Ultrafiltration membranes demonstrated superior performance and nutrient retention compared to microfiltration membranes. By optimizing operational parameters and cleaning conditions, a sustainable direct membrane filtration process with controlled fouling and improved resource recovery can be developed for wastewater treatment.

engineering, chemical, environmental,water resources
Performance of resin adsorption and ozonation pretreatment in mitigating organic fouling of reverse osmosis membrane

Jian Shen,Yi Yuan,Feng Duan,Yuping Li

DOI: https://doi.org/10.1016/j.jwpe.2023.103688

IF: 7

2023-03-31

Journal of Water Process Engineering

Abstract:Effective pretreatment of reverse osmosis (RO) influent is of great importance for reducing membrane fouling risks during coking wastewater desalination. In this study, the combined resin adsorption and ozonation pretreatment was investigated on alleviating RO membrane organic fouling. The performance of combined process was compared with only resin adsorption or ozonation, which was evaluated in terms of changes in chemical oxygen demand (COD), ultraviolet-visible index, and three-dimensional excitation-emission matrix fluorescence spectra. RO membrane fouling tests were conducted to examine the effects of pretreatment on flux decline and filtration resistance. The surface morphology and functional groups of membrane before and after fouling was characterized by scanning electron microscopy and infrared spectroscopy. The correlation between major organic matter in the wastewater and normalized RO membrane flux was established via multiple linear regression equations. The results showed that ozonation was more effective in removing COD and fluorescent organics than resin adsorption. Moreover, the combined bifunctional resin adsorption/ozonation unit showed the best performance, with COD and UV 254 removal rates of 49.4 % and 88.0 %, respectively. The fluorescence intensity of each component decreased significantly. Meanwhile, the polysaccharide and protein components of the RO membrane fouling layer were effectively reduced by 67.2 % and 80.8 %, respectively. Most importantly, the combined pretreatment substantially reduced the decline in membrane flux and filtration resistance. Meanwhile, the fulvic acid-like organics in the wastewater showed high correlations with normalized membrane flux. The regression equation was beneficial for RO membrane fouling evaluation.

engineering, chemical, environmental,water resources
[Behavior of leukocytic lipids in blennorrhagic subjects].

M. Dogliotti,F. Gemesio

1952-03-01

Abstract:
Development of a high-rate submerged anaerobic membrane bioreactor

I Mahmoud,W J Gao,B Q Liao,J Cumin,M Dagnew,Y Hong

DOI: https://doi.org/10.1080/09593330.2017.1309076

Abstract:Typically, anaerobic membrane bioreactors are operated at an organic loading rate (OLR) less than 10 kg chemical oxygen demand (COD)/m3 d. This paper discusses the development and performance of a high-rate submerged anaerobic membrane bioreactor (SAnMBR) for a high-strength synthetic industrial wastewater treatment. An OLR as high as 41 kg COD/m3 d was achieved with excellent COD removal efficiency (>99%). The membrane was operated at constant fluxes (9.4-9.9 ± 0.5 L/m2 h) and the change in trans-membrane pressure (TMP) was monitored to characterize the membrane performance. The results showed a low TMP (<5 kPa) under steady-state operation with only biogas sparging and relaxation as control strategy for over 300 days, implying no significant fouling was developed. Inorganic fouling was the dominant fouling mechanism occurred at the end of the study. The results suggest that the newly developed SAnMBR configuration can treat high-strength wastewater at lower capital expenditure while still providing superior effluent quality for water reuse or system closure.
Performance Analysis for the Anaerobic Membrane Bioreactor Combined with the Forward Osmosis Membrane Bioreactor: Process Conditions Optimization, Wastewater Treatment and Sludge Characteristics

Yi Ding,Zhansheng Guo,Xuguang Hou,Junxue Mei,Zhenlin Liang,Zhipeng Li,Chunpeng Zhang,Chao Jin

DOI: https://doi.org/10.3390/w12112958

IF: 3.53

2020-10-22

Water

Abstract:The anaerobic membrane bioreactors (AnMBR) were operated at 35 °C (H-AnMBR) and 25 °C (L-AnMBR) for long-term wastewater treatment. Two aerobic forward osmosis membrane bioreactors (FOMBRs) were utilized to treat the effluents of H-AnMBR and L-AnMBR, respectively. During the 180 days of operation, it is worth noting that the combined system was feasible, and the pollutant removal efficiency was higher. Though the permeate chemical oxygen demand (COD) of H-AnMBR (18.94 mg/L) was obviously lower than that of L-AnMBR (51.09 mg/L), the permeate CODs of the FOMBRs were almost the same with the average concentrations of 7.57 and 7.58 mg/L for the H-FOMBR and L-FOMBR, respectively. It was interesting that for both the AnMBRs, the permeate total nitrogen (TN) concentration was higher than that in bulk phase. However, the TN concentrations in the effluent remained stable with the values of 20.12 and 15.22 mg/L in the H-FOMBR and L-FOMBR effluents, respectively. For the two systems, the characteristics of activated sludge flocs were different for H-AnMBR-FOMBR sludge and L-AnMBR-FOMBR sludge. The viscosity of L-AnMBR-activated sludge (2.09 Pa·s) was higher compared to that of H-AnMBR (1.31 Pa·s), while the viscosity of activated sludge in L-FOMBR (1.44 Pa·s) was a little lower than that in H-FOMBR (1.48 Pa·s). The capillary water absorption time of L-AnMBR-activated sludge (69.6 s) was higher compared to that of H-AnMBR (49.5 s), while the capillary water absorption time of activated sludge in L-FOMBR (14.6 s) was little lower than that in H-FOMBR (15.6 s). The particle size of H-AnMBR-activated sludge (119.62 nm) was larger than that of L-AnMBR-activated sludge (84.92 nm), but the particle size of H-FOMBR-activated sludge (143.81 nm) was significantly smaller than that of L-FOMBR-activated sludge (293.38 nm). The observations of flocs indicated that the flocs of activated sludge in H-AnMBR were relatively loose, while the flocs of L-AnMBR were relatively tight. The fine sludge floc was less present in the L-FOMBR than in the H-FOMBR. Therefore, in the process of sewage treatment, the influent of each unit in the AnMBR-FOMBR system should have suitable organic content to maintain the particle sizes of sludge flocs.

environmental sciences,water resources
Critical review on salt tolerance improvement and salt accumulation inhibition strategies of osmotic membrane bioreactors

Shilong Li,Liang Duan,Hengliang Zhang,Yang Zhao,Mingyue Li,Yanyan Jia,Qiusheng Gao,Huibin Yu

DOI: https://doi.org/10.1016/j.biortech.2024.130957

IF: 11.4

2024-06-14

Bioresource Technology

Abstract:The osmotic membrane bioreactor (OMBR) is a novel wastewater treatment and resource recovery technology combining forward osmosis (FO) and membrane bioreactor. It has attracted attention for its low energy consumption and high contaminant removal performance. However, in the long-term operation, OMBR faces the problem of salt accumulation due to high salt rejection and reverse salt flux, which affects microbial activity and contaminants removal efficiency. This review analyzed the feasibility of screening salt-tolerant microorganisms and determining salinity thresholds to improve the salt tolerance of OMBR. Combined with recent research, the inhibition strategies for salt accumulation were reviewed, including the draw solution, FO membrane, operating conditions and coupling with other systems. It is hoped to provide a theoretical basis and practical guidance for the further development of OMBR. Finally, future research directions were prospected. This review provides new insights for achieving stable operation of OMBR and promotes its wide application.

energy & fuels,biotechnology & applied microbiology,agricultural engineering

Chiasmatic arachnoiditis. A case report and review.

Anaerobic Digestion Performance of Concentrated Municipal Sewage by Forward Osmosis Membrane: Focus on the Impact of Salt and Ammonia Nitrogen.

Probing The Key Foulants And Membrane Fouling Under Increasing Salinity In Anaerobic Osmotic Membrane Bioreactors For Low-Strength Wastewater Treatment

Direct Concentration of Municipal Sewage by Forward Osmosis and Membrane Fouling Behavior

Determination of the critical draw solution concentration for anaerobic microfiltration osmotic membrane bioreactors

Black odorous water concentrating by forward osmosis (FO) with aquaporin biomimetic membranes: Pollutants concentrating and membrane fouling characteristics

Induction chemotherapy with gemcitabine and cisplatin in paranasal sinus tumours.

Aerobic SMBR/reverse Osmosis System Enhanced by Fenton Oxidation for Advanced Treatment of Old Municipal Landfill Leachate

Effects of Critical Operation and Cleaning Parameters on Performances and Economic Benefits of Biogas Slurry Concentration by Forward Osmosis Membrane

Lower bounds on blow up solutions of the three-dimensional Navier–Stokes equations in homogeneous Sobolev spaces

Efficient organic enrichment from sludge filtrate via a forward osmosis membrane process

Deciphering mono/multivalent draw solute-induced microbial ecology and membrane fouling in anaerobic osmotic membrane bioreactor

Utilization of unrejected ammonium for fouling prevention in a forward osmosis process tested with real primary wastewater from Hong Kong

Osmotic versus conventional membrane bioreactors integrated with reverse osmosis for water reuse: Biological stability, membrane fouling, and contaminant removal

Performance and membrane fouling behaviors analysis with SVR-LibSVM model in a submerged anaerobic membrane bioreactor treating low-strength domestic sewage

Direct Membrane Filtration (DMF) of municipal wastewater – A study on the prevention and remediation of fouling

Performance of resin adsorption and ozonation pretreatment in mitigating organic fouling of reverse osmosis membrane

[Behavior of leukocytic lipids in blennorrhagic subjects].

Development of a high-rate submerged anaerobic membrane bioreactor

Performance Analysis for the Anaerobic Membrane Bioreactor Combined with the Forward Osmosis Membrane Bioreactor: Process Conditions Optimization, Wastewater Treatment and Sludge Characteristics

Critical review on salt tolerance improvement and salt accumulation inhibition strategies of osmotic membrane bioreactors