Carbon quantum dots enriching molecular nickel polyoxometalate over CdS semiconductor for photocatalytic water splitting

Yinjuan Dong,Qing Han,Qiyu Hu,Chunjiang Xu,Congzhao Dong,Yong Peng,Yong Ding,Yaqian Lan

DOI: https://doi.org/10.1016/j.apcatb.2021.120214

2021-09-01

Abstract:<p>An efficient and stable photocatalyst for overall water splitting is desirable for solar-energy conversion. Herein, Ni₄P₂ catalyst was obtained in situ photoreaction semiconductor composite and [Ni₄(H₂O)₂(PW₉O₃₄)₂]^10- (Ni₄P₂). Photocatalytic hydrogen evolution from pure water is realized using CdS as the light harvester, CQDs as the electron acceptor and donor and Ni₄P₂ as catalyst without addition sacrificial reagents under visible light irradiation (λ = 420 nm), which exhibits water splitting activity with H₂ evolution rate up to 145 μmol g_cat^-1 h^-1. Experiments confirm the electrons transfer from CdS to CQDs, then to Ni₄P₂, resulting in accumulation of the electrons in Ni₄P₂ for H₂ evolution. The generated holes at the VB of CdS transfer to CQDs and oxidize H₂O to H₂O₂. The rotating ring-disk electrode test confirms the two-electron process (2H₂O → H₂ + H₂O₂). This work proposes an elegant strategy for how to design multicomponent photocatalyst to realize efficient water splitting.</p>

chemistry, physical,engineering, chemical, environmental

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to develop an efficient and stable photocatalyst for overall water splitting to achieve solar energy conversion. Specifically, the researchers constructed a new multi - component photocatalytic system (Ni4P2 - CQDs@CdS), which can simultaneously generate hydrogen (H2) and hydrogen peroxide (H2O2) from pure water without adding sacrificial reagents under visible - light irradiation (λ = 420 nm). The design of this system aims to overcome several major challenges encountered by traditional photocatalysts in the water - splitting process:

1. **Narrow bandgap**: The photocatalyst needs to have an appropriate bandgap, which can both exceed the high Gibbs free energy required for water splitting (ΔG = 237 kJ/mol, equivalent to 1.23 eV) and effectively capture visible light (the bandgap should be lower than 3.0 eV).

2. **Appropriate band positions**: The conduction band (CB) and valence band (VB) positions of the photocatalyst should be suitable for driving the water - splitting reaction, that is, the conduction - band potential should be ≤0 V, and the valence - band potential should be ≥1.23 V (relative to the standard hydrogen electrode NHE, pH = 0).

3. **Efficient charge separation and transfer**: Photo - generated carriers need to be efficiently separated and transferred to suppress their recombination.

4. **Corrosion resistance**: The photocatalyst should have sufficient corrosion resistance under illumination conditions.

To achieve these goals, the researchers utilized carbon quantum dots (CQDs) as electron acceptors and donors, nickel - based polyoxometalates (Ni4P2) as catalysts, and cadmium sulfide (CdS) as light absorbers. Through this combination, they successfully achieved efficient water splitting and studied the electron - transfer mechanism in detail. They verified that electrons are transferred from CdS to CQDs, then from CQDs to Ni4P2, and finally accumulate on Ni4P2 for hydrogen generation. Meanwhile, the holes generated in the valence band of CdS are transferred to CQDs, oxidizing water to hydrogen peroxide (H2O2).

In conclusion, this paper proposes a novel multi - component photocatalytic system design strategy, providing new ideas for achieving efficient water splitting.