Abstract:The load distribution among lumbar spinal structures-still an unanswered question-has been in the focus of this hybrid experimental and simulation study. First, the overall passive resistive torque-angle characteristics of healthy subjects' lumbar spines during flexion-extension cycles in the sagittal plane were determined experimentally by use of a custom-made trunk-bending machine. Second, a forward dynamic computer model of the human body that incorporates a detailed lumbar spine was used to (1) simulate the human-machine interaction in accordance with the experiments and (2) validate the modeled properties of the load-bearing structures. Third, the computer model was used to predict the load distribution in the experimental situation among the implemented lumbar spine structures: muscle-tendon units, ligaments, intervertebral discs, and facet joints. Nine female and 10 male volunteers were investigated. Lumbar kinematics were measured with a marker-based infrared device. The lumbar flexion resistance was measured by the trunk-bending machine through strain gauges on the axes of the machine's torque motors. Any lumbar muscle activity was excluded by simultaneous sEMG monitoring. A mathematical model was used to describe the nonlinear flexion characteristics. The subsequent extension branch of a flexion-extension torque-angle characteristic could be significantly distinguished from its flexion branch by the zero-torque lordosis angle shifted to lower values. A side finding was that the model values of ligament and passive muscle stiffnesses, extracted from well-established literature sources, had to be distinctly reduced in order to approach our measured overall lumbar stiffness values. Even after such parameter adjustment, the computer model still predicts too stiff lumbar spines in most cases in comparison with experimental data. A review of literature data reveals a deficient documentation of anatomical and mechanical parameters of spinal ligaments. For instance, rest lengths of ligaments-a very sensitive parameter for simulations-and cross-sectional areas turned out to be documented at best incompletely. Yet by now, our model well reproduces the literature data of measured pressure values within the lumbar disc at level L4/5. Stretch of the lumbar dorsal (passive) muscle and ligament structures as an inescapable response to flexion can fully explain the pressure values in the lumbar disc. Any further external forces like gravity, or any muscle activities, further increase the compressive load on a vertebral disc. The impact of daily or sportive movements on the loads of the spinal structures other than the disc cannot be predicted ad hoc, because, for example, the load distribution itself crucially determines the structures' current lever arms. In summary, compressive loads on the vertebral discs are not the major determinants, and very likely also not the key indicators, of the load scenario in the lumbar spine. All other structures should be considered at least equally relevant in the future. Likewise, load indicators other than disc compression are advisable to turn attention to. Further, lumbar flexion is a self-contained factor of lumbar load. It may be worthwhile, to take more consciously care of trunk flexion during daily activities, for instance, regarding long-term effects like lasting repetitive flexions or sedentary postures.

Tensile Force Limits of the Sheep Spine: Comparison to Forces Required to Extricate Grain Entrapped Victims

Contributing Causes of Injury or Death in Grain Entrapment, Engulfment, and Extrication

Force Distribution Within Spinal Tissues During Posterior to Anterior Spinal Manipulative Therapy: A Secondary Analysis

An explorative, biomechanical analysis of spine motion during out-of-hospital extrication procedures

Mechanical Evaluation of Human Cadaveric Lumbar Soft Tissues Suggests Possible Physiological Stress Shielding Within Musculoskeletal Soft Tissues by the Thoracolumbar Fascia

Failure Tolerance of the Human Lumbar Spine in Combined Compression and Flexion Loading

Trunk strength, muscle activity and spinal loads in maximum isometric flexion and extension exertions: a combined in vivo-computational study

Mechanical properties of spinal cord grey matter and white matter in confined compression

Twente Spine Model: A thorough investigation of the spinal loads in a complete and coherent musculoskeletal model of the human spine

Load-Sharing and Kinematics of the Human Cervical Spine Under Multi-Axial Transverse Shear Loading: Combined Experimental and Computational Investigation

Loads distributed in vivo among vertebrae, muscles, spinal ligaments, and intervertebral discs in a passively flexed lumbar spine

Subject-Specific Geometry of FE Lumbar Spine Models for the Replication of Fracture Locations Using Dynamic Drop Tests

A novel finite element model of the ovine lumbar intervertebral disc with anisotropic hyperelastic material properties

Correlation Between Quantitative Cage Pressure Measurements and Surgeons' Qualitative Tactile Assessments During Extraction in Lumbar Lateral Interbody Fusion: A Cadaveric Study

Characterization of a developing lumbar arthrodesis in a sheep model with quantitative instability

Human lumbar spinal column injury criteria from vertical loading at the base: Applications to military environments

433 Orientation of the Lumbar Spine During Dynamic Compression Influences Fracture Characteristics

Comparison of intradiscal pressures and spinal fixator loads for different body positions and exercises

Intervertebral disc deformation in the lower lumbar spine during object lifting measured in vivo using indwelling bone pins

Biomechanical analysis of the tandem spinal external fixation in a multiple-level noncontiguous lumbar fractures model: a finite element analysis

A comparison of fracture response in female and male lumbar spine in simulated under body blast component tests