Interrelationship of pyrrole and globin metabolism in beta-thalassaemia.

M. Kreimer‐Birnbaum,R. Bannerman

British Journal of Haematology

Abstract:

What problem does this paper attempt to address?

The occurrence of ultralow friction even superlubricity for graphene oxide/hydrogenated diamond-like carbon composites in multi-environments

Guomin Yu,Kexin Ren,Wenchao Wu,Han Wang,Wenjing Chen,Wenyue Tang,Zhenbin Gong

DOI: https://doi.org/10.1016/j.vacuum.2023.112803

IF: 4

2023-11-01

Vacuum

Abstract:The establishment of ultralow friction and superlubricity can significantly decrease the dissipation of energy and failure of parts in moving mechanical systems. Hydrogenated diamond-like carbon (H-DLC) film can realize the frictionless state at engineering scale by the stress-induced graphitization that leads to the formation of the vital superlubricious structures: graphene-like carbon and onion-like carbon during the sliding process. Herein, we designed some composites by combination H-DLC film and graphene oxide (GO) nanosheets to provide the “pre-graphitized” sliding interface for decreasing the friction. Frictional behaviors of these composites in different atmospheres and the as-formed structures of sliding interfaces were investigated comprehensively in this work. It was demonstrated that the existence of GO on H-DLC film could significantly decrease the friction and even establish the near friction-vanishing state. The structural investigations showed that the existence of GO on H-DLC film could work as a “pre-graphitization” process, hinder the structural evolution of H-DLC film from amorphous to sp2-rich ones and endow the composite with ultralow friction even superlubricious performance. The investigation would provide some helpful advices for H-DLC film to establish ultralow even superlow friction from inert atmospheres to humid air at engineering scale by depositing GO flakes on the surface of H-DLC film.

materials science, multidisciplinary,physics, applied
The high-speed sliding friction of graphene and novel routes to persistent superlubricity

Yilun Liu,François Grey,Quanshui Zheng

DOI: https://doi.org/10.1038/srep04875

IF: 4.6

2014-01-01

Scientific Reports

Abstract:Recent experiments on microscopic graphite mesas demonstrate reproducible high-speed microscale superlubricity, even under ambient conditions. Here, we explore the same phenomenon on the nanoscale, by studying a graphene flake sliding on a graphite substrate, using molecular dynamics. We show that superlubricity is punctuated by high-friction transients as the flake rotates through successive crystallographic alignments with the substrate. Further, we introduce two novel routes to suppress frictional scattering and achieve persistent superlubricity. We use graphitic nanoribbons to eliminate frictional scattering by constraining the flake rotation, an approach we call frictional waveguides . We can also effectively suppress frictional scattering by biaxial stretching of the graphitic substrate. These new routes to persistent superlubricity at the nanoscale may guide the design of ultra-low dissipation nanomechanical devices.
Self-Assembled Graphene Film As Low Friction Solid Lubricant in Macroscale Contact

Pu Wu,Xinming Li,Chenhui Zhang,Xinchun Chen,Shuyuan Lin,Hongyan Sun,Cheng-Te Lin,Hongwei Zhu,Jianbin Luo

DOI: https://doi.org/10.1021/acsami.7b04599

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:Promoted by the demand for solid lubricants, graphene has been proved to be a promising material for potential applications in reducing friction and wear. Here, a novel lubricating system where graphene sliding against graphene is developed to achieve low friction in macroscale contact. And the large area graphene film used here were prepared by a unique self-assembly technique based on Marangoni effect. Low friction coefficient of about 0.05 is obtained, and it is demonstrated that the film thickness, applied normal load and annealing process all have important influences on the tribological properties of graphene. The expedient fabrication procedure of large-area graphene film with excellent transferability and high-performance friction-reducing behaviors of the developed lubricating system both have a promising perspective in engineering applications.
Graphene-induced reconstruction of the sliding interface assisting the improved lubricity of various tribo-couples

Xuan Yin,Fan Wu,Xinchun Chen,Jianxun Xu,Pu Wu,Jinjin Li,Chenhui Zhang,Jianbin Luo

DOI: https://doi.org/10.1016/j.matdes.2020.108661

2020-06-01

Abstract:Graphene has emerged as one of the most promising solid lubricants owing to their exceptional lubricity. The atomically thin nature and its ability to conformally adsorb on the sliding surfaces provide unprecedented pathways for modifying the friction and wear behaviors of the mechanical moving parts. Here, the tribological responses of several representative tribo-couples including bare steel, diamond-like carbon and ceramic materials are investigated to explore the potentials of graphene as surface modifier. Specific emphasis is devoted to the graphene-induced reconstruction of the sliding interface and the growth mechanism of nanostructured tribofilms formed on the contact surface using high-resolution microscopic technique. The results reveal the unique properties of graphene regarding the friction reduction and wear protection irrespective of the types of counterpart materials, graphene-processed methods, dry or humid tests environments. Nevertheless, the interfacial features and the bonding characteristics of the tribofilms are diversified in each specific rubbing case, demonstrating the distinguished adaption capacity of graphene to the tribo-testing conditions. The present findings shed light on the lubrication phenomenon of graphene at the microscale and may provide useful design criterion for 2D-based solid lubricants.

materials science, multidisciplinary
Fluorinated Graphene: A Promising Macroscale Solid Lubricant under Various Environments.

Yanfei Liu,Jinjin Li,Xinchun Chen,Jianbin Luo

DOI: https://doi.org/10.1021/acsami.9b13060

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Graphene-related materials are promising solid lubricants owing to their easy shear between lattice layers. However, the coefficient of friction (COF) of graphene is not sufficiently low at the macroscale, and the lubrication performance is largely restricted by the external environment. In this study, we fabricated a fluorinated graphene (FG) coating on a stainless-steel substrate by a simple electrophoretic deposition in ethanol. The FG coating exhibited an excellent lubrication performance, which reduced the COF by 54.0 and 66.2% compared to those of pristine graphene and graphene oxide coatings, respectively. The lubrication enhancement of FG coating is attributed to its extremely low surface energy and interlaminar shear strength. The formation of ionic metal-fluorine chemical bonds provided a robust solid tribofilm and transfer layer on the friction pairs, which further increased the lubrication performance of the FG coating. The limited influence of the humidity on the lubrication performance of the FG coating is attributed to the hydrophobicity of the FG nanoflakes, which could prevent the influence of water molecules on the sliding interface. The excellent lubrication performance and better environmental adaptability of the FG make it a promising solid lubricant for mechanical engineering applications.
Temperature and Velocity Dependent Friction of a Microscale Graphite-Dlc Heterostructure

Yujie Gongyang,Wengen Ouyang,Cangyu Qu,Michael Urbakh,Baogang Quan,Ming Ma,Quanshui Zheng

DOI: https://doi.org/10.1007/s40544-019-0288-0

IF: 4.924

2020-01-01

Friction

Abstract:One of the promising approaches to achieving large scale superlubricity is the use of junctions between existing ultra-flat surface together with superlubric graphite mesas. Here we studied the frictional properties of microscale graphite mesa sliding on the diamond-like carbon, a commercially available material with a ultra-flat surface. The interface is composed of a single crystalline graphene and a diamond-like carbon surface with roughness less than 1 nm. Using an integrated approach, which includes Argon plasma irradiation of diamond-like carbon surfaces, X-ray photoelectron spectroscopy analysis and Langmuir adsorption modeling, we found that while the velocity dependence of friction follows a thermally activated sliding mechanism, its temperature dependence is due to the desorption of chemical groups upon heating. These observations indicate that the edges have a significant contribution to the friction. Our results highlight potential factors affecting this type of emerging friction junctions and provide a novel approach for tuning their friction properties through ion irradiation.
100 Km Wear-Free Sliding Achieved by Microscale Superlubric Graphite/dlc Heterojunctions under Ambient Conditions

Deli Peng,Jin Wang,Haiyang Jiang,Shuji Zhao,Zhanghui Wu,Kaiwen Tian,Ming Ma,Quanshui Zheng

DOI: https://doi.org/10.1093/nsr/nwab109

IF: 20.6

2021-01-01

National Science Review

Abstract:Wear-free sliding between two contacted solid surfaces is the ultimate goal in the effort to extend the lifetime of mechanical devices,especially when it comes to inventing new types of micro-electromechanical systems where wear is often a major obstacle.Here we report experimental observations of wear-free sliding for a micrometer-sized graphite flake on a diamond-like-carbon (DLC) surface under ambient conditions with speeds up to 2.5 m/s,and over a distance of 100 km.The coefficient of friction (COF) between the microscale graphite flake,a van der Waals (vdW) layered material and DLC,a non-vdW-layered material,is measured to be of the order of 10-3,which belongs to the superlubric regime.Such ultra-low COFs are also demonstrated for a microscale graphite flake sliding on six other kinds of non-vdW-layered materials with sub-nanometer roughness.With a synergistic analysis approach,we reveal the underlying mechanism to be the combination ofinterfacial vdW interaction,atomic-smooth interfaces and the low normal stiffness of the graphite flake.These features guarantee a persistent full contact of the interface with weak interaction,which contributes to the ultra-low COFs.Together with the extremely high in-plane strength ofgraphene,wear-free sliding is achieved.Our results broaden the scope of superlubricity and promote its wider application in the future.
Achieving Controllable Friction of Ultrafine-Grained Graphite HPG510 by Tailoring the Interfacial Nanostructures

Wei Qi,Peng Huang,Xinchun Chen,Jie Jin,Jianbin Luo

DOI: https://doi.org/10.1016/j.apsusc.2020.145731

IF: 6.7

2020-01-01

Applied Surface Science

Abstract:Graphite is an effective solid lubricant due to its self-lubricating properties. However, in practical environments such as ambient air and vacuum, the coefficient of friction (COF) of graphite is still high, resulting in serious wear that limits applications. In this study, two methods are proposed to improve the tribological properties of HPG510, including alcohol-processed two-dimensional (2D) nanomaterials as surface lubricating additives and deposition of a diamond-like carbon (DLC) film on the graphite surfaces. The results show that the COF of graphite decreases from 0.25 to 0.06 when lubricated by graphene oxide (GO)-processed alcohol solution. Similar performance is also observed for fluorinated graphene (GF), and tungsten disulfide (WS2) plus graphene (G) processed solutions. The identified mechanism is the combined lubrication effect of anhydrous alcohol and 2D lubricant materials. Meanwhile, the DLC-deposited graphite not only has a lower COF (similar to 0.10) but also possesses a significant enhancement of the wear resistance. An interesting finding about the anti-friction phenomenon is that some bulk DLC blocks are embedded in the lubricating tribolayer. The present work can provide reliable experimental evidence and a theoretical basis to expand the application field of bulk graphite.
Friction-induced Nano-Structural Evolution of Graphene As a Lubrication Additive

Jun Zhao,Junyuan Mao,Yingru Li,Yongyong He,Jianbin Luo

DOI: https://doi.org/10.1016/j.apsusc.2017.10.119

IF: 6.7

2018-01-01

Applied Surface Science

Abstract:Graphene has attracted enormous attention in the field of lubrication based on its excellent physical and chemical properties. Although many studies have obtained thermally or chemically-exfoliated graphene and investigated their wide and important application, few studies have reported their physical nanostructural evolution under friction. In this study, we investigated the lubrication properties of graphene additives with different layer numbers and interlayer spacing by exfoliating. The additives with a higher degrees of exfoliation changed to ordering under friction, and had better lubrication properties, while that with a lower degrees exhibited obvious structural defects and high friction. Therefore, the original degrees of exfoliation plays a key role in the structural evolution of graphene and superior lubrication can be achieved through the physical nano-structure changing to ordering, even graphitization. Furthermore, the ordered tribofilm on the frictional interfaces was parallel to the sliding direction, meaning the highly exfoliated graphene indeed reaching slippage between its layers, which wasn't experimentally discovered in previous studies. This work provides a new understanding of the relationship between friction-induced nano-structural evolution and lubrication properties of graphene as a lubrication additive, and has great potential for the structural design of graphene as a lubrication additive. (C) 2017 Elsevier B.V. All rights reserved.
Superlubricity of a Graphene/mos2 Heterostructure: a Combined Experimental and DFT Study

Linfeng Wang,Xiang Zhou,Tianbao Ma,Dameng Liu,Lei Gao,Xin Li,Jun Zhang,Yuanzhong Hu,Hui Wang,Yadong Dai,Jianbin Luo

DOI: https://doi.org/10.1039/c7nr01451a

IF: 6.7

2017-01-01

Nanoscale

Abstract:Graphene and other two-dimensional materials have been proved to be able to offer low friction. Here we assembled van der Waals heterostructures with graphene and molybdenum disulphide monolayers. The Raman spectrum together with a modified linear chain model indicate a two-orders-of-magnitude decrease in the interlayer lateral force constant, as compared with their homogeneous bilayers, indicating a possible routine to achieve superlubricity. The decrease in the interlayer lateral force constant is consistent with the ultrasmall potential energy corrugation during sliding, which is derived from density functional theory calculations. The potential energy corrugation is found to be determined by the sliding-induced interfacial charge density fluctuation, suggesting a new perspective to understand the physical origin of the atomic scale friction of two-dimensional materials.
Dissipation Mechanisms and Superlubricity in Solid Lubrication by Wet-Transferred Solution-Processed Graphene Flakes: Implications for Micro Electromechanical Devices

Renato Buzio,Andrea Gerbi,Cristina Bernini,Luca Repetto,Andrea Silva,Andrea Vanossi

DOI: https://doi.org/10.1021/acsanm.3c01477

2023-06-15

Abstract:Solution-processed few-layer graphene flakes, dispensed to rotating and sliding contacts via liquid dispersions, are gaining increasing attention as friction modifiers to achieve low friction and wear at technologically relevant interfaces. Vanishing friction states, i.e., superlubricity, have been documented for nearly-ideal nanoscale contacts lubricated by individual graphene flakes. However, there is no clear understanding if superlubricity might persist for larger and morphologically disordered contacts, as those typically obtained by incorporating wet-transferred solution-processed flakes into realistic microscale contact junctions. In this study, we address the friction performance of solution-processed graphene flakes by means of colloidal probe atomic force microscopy. We use a state-of-the-art additive-free aqueous dispersion to coat micrometric silica beads, which are then sled under ambient conditions against prototypical material substrates, namely, graphite and the transition metal dichalcogenides (TMDs) MoS2 and WS2. High resolution microscopy proves that the random assembly of the wet-transferred flakes over the silica probes results into an inhomogeneous coating, formed by graphene patches that control contact mechanics through tens-of-nanometers tall protrusions. Atomic-scale friction force spectroscopy reveals that dissipation proceeds via stick-slip instabilities. Load-controlled transitions from dissipative stick-slip to superlubric continuous sliding may occur for the graphene-graphite homojunctions, whereas single- and multiple-slips dissipative dynamics characterizes the graphene-TMD heterojunctions. Systematic numerical simulations demonstrate that the thermally activated single-asperity Prandtl-Tomlinson model comprehensively describes friction experiments involving different graphene-coated colloidal probes, material substrates, and sliding regimes. Our work establishes experimental procedures and key concepts that enable mesoscale superlubricity by wet-transferred liquid-processed graphene flakes. Together with the rise of scalable material printing techniques, our findings support the use of such nanomaterials to approach superlubricity in micro electromechanical systems.
Solid lubrication by wet-transferred solution-processed graphene flakes: dissipation mechanisms and superlubricity in mesoscale contacts

Renato Buzio,Andrea Gerbi,Cristina Bernini,Luca Repetto,Andrea Silva,Andrea Vanossi

DOI: https://doi.org/10.1021/acsanm.3c01477

2023-07-27

Abstract:Solution-processed few-layers graphene flakes, dispensed to rotating and sliding contacts via liquid dispersions, are gaining increasing attention as friction modifiers to achieve low friction and wear at technologically-relevant interfaces. Vanishing friction states, i.e. superlubricity, have been documented for nearly-ideal nanoscale contacts lubricated by individual graphene flakes; there is however no clear understanding if superlubricity might persist for larger and morphologically-disordered contacts, as those typically obtained by graphene wet transfer from a liquid dispersion. In this study we address the friction performance of solution-processed graphene flakes by means of colloidal probe Atomic Force Microscopy. We use an additive-free aqueous dispersion to coat micrometric silica beads, which are then sled under ambient conditions against prototypical material substrates, namely graphite and the transition metal dichalcogenides (TMDs) MoS2 and WS2. High resolution microscopy proves that the random assembly of the wet-transferred flakes over the silica probes results into an inhomogeneous coating, formed by graphene patches that control contact mechanics through tens-of-nanometers tall protrusions. Atomic-scale friction force spectroscopy reveals that dissipation proceeds via stick-slip instabilities. Load-controlled transitions from dissipative stick-slip to superlubric continuous sliding may occur for the graphene-graphite homojunctions, whereas single- and multiple-slips dissipative dynamics characterizes the graphene-TMD heterojunctions. Systematic numerical simulations demonstrate that the thermally-activated single-asperity Prandtl-Tomlinson model comprehensively describes friction experiments involving different graphene-coated colloidal probes, material substrates and sliding regimes.

Mesoscale and Nanoscale Physics,Materials Science
Interface‐Sliding‐Induced Graphene Quantum Dots Transferring to Fullerene‐Like Quantum Dots and Their Extraordinary Tribological Behavior

Renhui Zhang,Liping Xiong,Jibin Pu,Zhibin Lu,Guangan Zhang,Zhongyi He

DOI: https://doi.org/10.1002/admi.201901386

IF: 5.4

2019-10-29

Advanced Materials Interfaces

Abstract:<p>Carbon materials such as diamond, fullerene, graphene, and carbon nanotubes possess superior chemical and physical properties, which are widely used in various applications. Especially, since fullerene‐like carbon is successfully converted to graphene during sliding, the sliding‐induced microstructure transfer between carbon‐based materials should be given more attention. Here, the tribological behaviors of graphene‐based materials is investigated under the load of 196 N and the rotational speed of 1450 rpm using a four‐ball wear machine under deionized water. Results show that the friction coefficient continuously decreases with increasing sliding time and the wear scar diameter is just about 0.224 mm. Remarkably, graphene is severely ripped and loses its lubrication performance during sliding. Sliding induces graphene quantum dots converting to fullerene quantum dots, which would cooperate with the sliding‐reduced fullerene‐like structures containing WO<sub>2</sub> nanocrystals and sulfurized isobutene as extreme pressure lubricant additives instead of graphene to achieve low friction and wear. This work confirms that the low friction and wear under high load and fast rotation have a close relation to the microstructure transfer of interfacial carbon‐based materials, rather graphene, and provide practical approach for investigating the tribological behaviors of carbon‐based materials.</p>

materials science, multidisciplinary,chemistry
Superlubric Sliding of Graphene Auto‐Kirigami with Interfaces Containing Self‐Assembled Stripe‐Pattern Adsorbates

Pierce C. Sinnott,Majid Fazeli Jadidi,Daniel A. Sánchez,Li Yuan,Robert W. Carpick,Graham L. W. Cross

DOI: https://doi.org/10.1002/smll.202401979

IF: 13.3

2024-07-18

Small

Abstract:A ubiquitous stripe structure adsorbate that has previously been observed on graphene and graphitic surfaces is examined within twisted graphene‐graphene interfaces. This adsorbate is observed to be stable during sliding of layers in this interface and does not destroy the low friction (superlubricious) contact at the interface under ambient conditions. Van der Waals heterostructures formed by stacked 2D materials show exceptional electronic, mechanical, and optical properties. Superlubricity, a condition where atomically flat, incommensurate planes of atoms result in ultra‐low friction, is a prime example enabling, for example, self‐assembly of optically visible graphene nanostructures in air via a sliding auto‐kirigami process. Here, it is demonstrated that a subtle but ubiquitous adsorbate stripe structure found on graphene and graphitic surfaces in ambient conditions remains stable within the interface between twisted graphene layers as they slide over each other. Despite this contamination, the interface retains an exceptional superlubricious state with an estimated upper bound frictional shear strength of 10 kPa, indicating that direct atomic incommensurate contact is not required to achieve ambient superlubricity for 2D materials. The results suggest that any phenomena depending on 2D heterostructure interfaces such as exotic electronic behavior may need to consider the presence of stripe adsorbate structures that remain intercalated.

materials science, multidisciplinary,nanoscience & nanotechnology,physics, applied,chemistry, physical, condensed matter
Molecular Origin of Superlubricity between Graphene and Highly Hydrophobic Surface in Water.

Jinjin Li,Wei Cao,Jianfeng Li,Ming Ma,Jianbin Luo

DOI: https://doi.org/10.1021/acs.jpclett.9b00952

2019-01-01

Abstract:Graphene is efficient to provide ultralow friction after the formation of an incommensurate interface but is limited to dry contact conditions and specific lattice structures. In this Letter, a new strategy is proposed to achieve the superlubricity of graphene through the creation of a sliding interface between graphene and a highly hydrophobic surface of self-assembled fluoroalkyl monolayers (SAFMs) in water. A superlow friction coefficient of mu = 0.0003 was obtained, demonstrating the extremely low shear stress between graphene and hydrophobic SAFMs in water. Molecular dynamics (MD) simulation shows that a nanometer-thick water layer is intercalated between graphene and hydrophobic SAFMs, and the weak interactions between water molecules and graphene provide a small energy barrier for water molecules sliding on graphene, which contributes to superlubricity. This finding reveals how to form a superlubricity interface by water intercalation, which has implications for minimizing the friction of layered materials and hydrophobic surfaces in water.
Enhancement of Friction Performance of Fluorinated Graphene and Molybdenum Disulfide Coating by Microdimple Arrays

Yanfei Liu,Jinjin Li,Shuang Yi,Xiangyu Ge,Xinchun Chen,Jianbin Luo

DOI: https://doi.org/10.1016/j.carbon.2020.05.041

IF: 10.9

2020-01-01

Carbon

Abstract:Two-dimensional (2D) materials, including graphene-family materials and molybdenum disulfide (MoS2), have been used as solid lubricants because of their low interlayer shear strength. In this study, a fluorinated graphene (FG)–MoS2 nanocomposite coating was deposited on a stainless-steel substrate with a laser surface textured dimple array. The FG–MoS2 nanocomposite coating deposited on a textured surface led to the reduction in the coefficient of friction to 0.036, and it significantly reduced wear and extended the lifetime compared with those obtained using the MoS2 coating. The excellent tribological performance is attributed to the synergetic effect between FG and MoS2 nanoflakes and the function of texture, where the MoS2 nanoflakes dominate the lubrication performance because of interlayer shearing, and the FG nanoflakes suppress the influence of external humidity on MoS2 nanoflakes because of their hydrophobic nature. Meanwhile, the textured surface can promote the formation of a tribofilm through changing the stress distribution at the sliding interface and act as a reservoir for nanoflakes, leading to a much lower friction and longer lifetime. This has implications for the development of functional surfaces with excellent lubrication and wear-resistance performances with 2D materials.
Macroscale Superlubricity Achieved on the Hydrophobic Graphene Coating with Glycerol.

Yanfei Liu,Jinjin Li,Xiangyu Ge,Shuang Yi,Hongdong Wang,Yuhong Liu,Jianbin Luo

DOI: https://doi.org/10.1021/acsami.0c01515

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:Introduction of graphene-family nanoflakes in liquid results in a reduction in friction and enhanced wear resistance. However, the high demand for dispersity and stability of the nanoflakes in liquid largely restricted the choice of graphene-family nanoflakes thus far. This study proposed a new strategy to overcome this limitation, involving the formation of a graphene coating with deposited graphene-family nanoflakes, followed by the lubrication of the coating with glycerol solution. Pristine graphene (PG), fluorinated graphene (FG), and graphene oxide (GO) nanoflakes were chosen to be deposited on the respective SiO2 substrates to form graphene coatings, and then an aqueous solution of glycerol was used as lubricant. The coefficient of friction (COF) and wear rate were reduced for all deposited coatings. However, the PG coating exhibited better lubrication and antiwear performance than FG and GO coatings. A robust superlubricity with COF of approximately 0.004 can be achieved by combining glycerol with the PG coating. The superlubricity mechanism was attributed to the formation of a tribofilm, mainly composed of graphene nanoflakes in the contact zone. The extremely low friction achieved on the hydrophobic graphene coating with liquid can aid in the development of a high-performing new lubrication system for industrial applications.
Ultra-low Friction of A-C:H Films Enabled by Lubrication of Nanodiamond and Graphene in Ambient Air

Peng Huang,Wei Qi,Xuan Yin,Junho Choi,Xinchun Chen,Jisen Tian,Jianxun Xu,Huaichao Wu,Jianbin Luo

DOI: https://doi.org/10.1016/j.carbon.2019.08.010

IF: 10.9

2019-01-01

Carbon

Abstract:Hydrogenated amorphous carbon (a-C:H) is subjected to abnormal high friction in ambient air, and the possibility to retain an ultra-low friction state remains as a great challenge. Here, nanodiamond and graphene were used as solid lubricants to improve the tribological properties of two representative types of a-C:H films with 20 at.% and 40 at.% hydrogen contents, respectively. The results emphasize the exceptionally synergetic lubrication effect of nanodiamond + graphene composite with a mass ratio of 1:1 and a solution-processed concentration of 0.1 mg/mL. An ultra-low friction coefficient of similar to 0.02 was achieved for a-C:H (20 at.% H) film, and more strikingly, a dramatic reduction in COF from 0.52 to 0.07 was realized in a-C:H (40 at.% H) film. Meanwhile, the wear rates of the counterparts in both cases are significantly reduced in the presence of nano-lubricants. The lubricity mechanisms are mainly based on the in-situ growth of nanostructured tribolayers. The roles of a-C:H film bonding characteristic and the tribo-induced structural evolution of nano-lubricants in the build-up of anti-friction and wear-resistant tribolayers are discussed. These findings can enrich the understanding of surface modification pathways to a-C:H films via low-dimensional nano-lubricants and help to develop more adaptive and robust solid carbon films. (C) 2019 Elsevier Ltd. All rights reserved.
Graphitic Encapsulation and Electronic Shielding of Metal Nanoparticles to Achieve Metal-Carbon Interfacial Superlubricity.

Ruiyun Li,Xing Yang,Yongfu Wang,Junyan Zhang,Jiangong Li

DOI: https://doi.org/10.1021/acsami.0c18900

IF: 9.5

2021-01-01

ACS Applied Materials & Interfaces

Abstract:Presently, approaches to achieve superlubricity for diamond-like carbon (DLC) films rely heavily on the film deposition techniques and parameters, such as other nonmetallic element incorporation and structure optimization. In this work, we report a new feasible pathway to achieve superlubricity for DLC films, which is not dependent on the film preparation parameters but rather on the external effects, i.e., sliding interfacial addition of metal nanoparticles (Cu and Ni). The approach controls the structures of wear products by the introduction of metal nanoparticles and the subsequent effect of metal catalysts, to in situ form graphene-coated particles without impacting the overall performances of the films. Through detailed experimental investigations combined with density functional theory (DFT) simulations, graphitic encapsulation and electronic shielding of metal nanoparticles are responsible for the dramatic changes at the frictional interface leading to metal-carbon interfacial superlubricity. We expect that the approach will enrich the understanding of the lubrication mechanism of DLC films and promote the DLC films' superlubricity toward applications.
Kinetic Friction of Structurally Superlubric 2D Material Interfaces

Jin Wang,Ming Ma,Erio Tosatti

DOI: https://doi.org/10.1016/j.jmps.2023.105396

2023-12-15

Abstract:The ultra-low kinetic friction F_k of 2D structurally superlubric interfaces, connected with the fast motion of the incommensurate moiré pattern, is often invoked for its linear increase with velocity v_0 and area A, but never seriously addressed and calculated so far. Here we do that, exemplifying with a twisted graphene layer sliding on top of bulk graphite -- a demonstration case that could easily be generalized to other systems. Neglecting quantum effects and assuming a classical Langevin dynamics, we derive friction expressions valid in two temperature regimes. At low temperatures the nonzero sliding friction velocity derivative dF_k/dv_0 is shown by Adelman-Doll-Kantorovich type approximations to be equivalent to that of a bilayer whose substrate is affected by an analytically derived effective damping parameter, replacing the semi-infinite substrate. At high temperatures, friction grows proportional to temperature as analytically required by fluctuation-dissipation. The theory is validated by non-equilibrium molecular dynamics simulations with different contact areas, velocities, twist angles and temperatures. Using 6^{\circ}-twisted graphene on Bernal graphite as a prototype we find a shear stress of measurable magnitude, from 25 kPa at low temperature to 260 kPa at room temperature, yet only at high sliding velocities such as 100 m/s. However, it will linearly drop many orders of magnitude below measurable values at common experimental velocities such as 1 {\mu}m/s, a factor 10^{-8} lower. The low but not ultra-low "engineering superlubric" friction measured in existing experiments should therefore be attributed to defects and/or edges, whose contribution surpasses by far the negligible moiré contribution.

Materials Science,Mesoscale and Nanoscale Physics,Statistical Mechanics

Interrelationship of pyrrole and globin metabolism in beta-thalassaemia.

The occurrence of ultralow friction even superlubricity for graphene oxide/hydrogenated diamond-like carbon composites in multi-environments

The high-speed sliding friction of graphene and novel routes to persistent superlubricity

Self-Assembled Graphene Film As Low Friction Solid Lubricant in Macroscale Contact

Graphene-induced reconstruction of the sliding interface assisting the improved lubricity of various tribo-couples

Fluorinated Graphene: A Promising Macroscale Solid Lubricant under Various Environments.

Temperature and Velocity Dependent Friction of a Microscale Graphite-Dlc Heterostructure

100 Km Wear-Free Sliding Achieved by Microscale Superlubric Graphite/dlc Heterojunctions under Ambient Conditions

Achieving Controllable Friction of Ultrafine-Grained Graphite HPG510 by Tailoring the Interfacial Nanostructures

Friction-induced Nano-Structural Evolution of Graphene As a Lubrication Additive

Superlubricity of a Graphene/mos2 Heterostructure: a Combined Experimental and DFT Study

Dissipation Mechanisms and Superlubricity in Solid Lubrication by Wet-Transferred Solution-Processed Graphene Flakes: Implications for Micro Electromechanical Devices

Solid lubrication by wet-transferred solution-processed graphene flakes: dissipation mechanisms and superlubricity in mesoscale contacts

Interface‐Sliding‐Induced Graphene Quantum Dots Transferring to Fullerene‐Like Quantum Dots and Their Extraordinary Tribological Behavior

Superlubric Sliding of Graphene Auto‐Kirigami with Interfaces Containing Self‐Assembled Stripe‐Pattern Adsorbates

Molecular Origin of Superlubricity between Graphene and Highly Hydrophobic Surface in Water.

Enhancement of Friction Performance of Fluorinated Graphene and Molybdenum Disulfide Coating by Microdimple Arrays

Macroscale Superlubricity Achieved on the Hydrophobic Graphene Coating with Glycerol.

Ultra-low Friction of A-C:H Films Enabled by Lubrication of Nanodiamond and Graphene in Ambient Air

Graphitic Encapsulation and Electronic Shielding of Metal Nanoparticles to Achieve Metal-Carbon Interfacial Superlubricity.

Kinetic Friction of Structurally Superlubric 2D Material Interfaces