Abstract:In recent years, remarkable interest has been focused on the Friction Stir Welding (FSW) process, by academic as well as industrial research groups. Conceptually, the FSW process is quite simple: a non-consumable rotating tool is plunged between the adjoining edges of the parts to be welded and moved along the desired weld line. Frictional and viscous heat generation increases the work piece temperature, softening the processing material and forcing it to flow around the pin. Although FSW has been effectively applied in welding of several materials, such as copper, steel, magnesium, and titanium, considerable attention is still focused on aluminum welding, in particular for transport applications. Recent literature clearly evidenced microstructural variations in the stir zone, imputable to continuous dynamic recrystallization phenomena, leading to the formation of a finer equiaxed grains. Moreover, depending on the specific alloy, thermal cycles can induce coarsening or dissolution of precipitates in the thermo-mechanically affected zone (TMAZ) and in the heat affected zone (HAZ). The influence of the aforementioned microstructural aspects on mechanical properties and formability of FSWed assemblies is also well recognized. The aim of this paper is to numerically and experimentally investigate the influence of process parameters, namely rotating speed and welding speed, on microstructural aspects in AA2024-T3 friction stir butt welds. A three-dimensional Computational Fluid Dynamic (CFD) model has been implemented to simulate the process. A viscoplastic material model, based on Wright and Sheppard modification of the constitutive model initially proposed by Sellars and Tegart has been implemented in the commercial package ANSYS CFX, considering an Eulerian framework. Tool-workpiece interaction has been modeled assuming partial sticking/sliding condition, and incorporating both frictional and viscous contributions to the heat generation. Microstructural aspects have been numerically predicted using the Zenner-Holloman parameter and experimentally measured by means of conventional metallographic techniques. Satisfactory agreement has been found between simulated and experimental results. The influence of process parameters on mechanical properties has also been highlighted.

Correction: Tamadon, A.; et al. Internal Material Flow Layers in AA6082-T6 Butt-Joints during Bobbin Friction Stir Welding. Metals 2019, 9, 1059

Correction: Tamadon et al. Development of Metallographic Etchants for the Microstructure Evolution of A6082-T6 BFSW Welds. Metals 2017, 7, 423

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints

A Numerical and Experimental Analysis of Microstructural Aspects in AA2024-T3 Friction Stir Welding

An Experimental Study On Friction Stir Welding Of Aluminum-Magnesium Alloys For Improved Mechanical Properties Of Tailor Welded Blanks.

Integral and Layered Mechanical Properties of Friction Stir Welded Joints of 2014 Aluminium Alloy

Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt joints

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Material-flow behavior during friction-stir welding of 6082-T6 aluminum alloy

A Simulation Study on Material Flow and Mixing Mechanism in Dissimilar Friction Stir Welding of AA6061 and AZ31 Alloys

Effect of friction stir welding parameters on the material flow, mechanical properties and corrosion behavior of dissimilar AA5083-AA6061 joints

Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds

Material Flow Behavior in Linear Friction Welding of TC4 Titanium Alloy

Mechanical Characteristic and Stress-Strain Modelling of Friction Stir Welded 6061-T6 Aluminium Alloy Butt Joints

Dissimilar Friction Stir Welds in AA2219-AA5083 Aluminium Alloys: Effect of Process Parameters on Material Inter-Mixing, Defect Formation, and Mechanical Properties

Investigation of tool offset on the microstructure and mechanical properties of AA6061-T6/PC Friction Stir Butt Welding joint

Asymmetric mechanical properties and tensile behaviour prediction of aluminium alloy 5083 friction stir welding joints

Material Flow and Microstructure in the Friction Stir Butt Welds of the Same and Dissimilar Aluminum Alloys

Effect of material flow behavior on the formation of interfacial reaction layers and fatigue performance of dissimilar friction stir welded S45C and AA6061-T6

Tailoring the Microstructure of an AA5754 Aluminum Alloy by Tuning the Combination of Heat Treatment, Friction Stir Welding, and Cold Rolling

Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys