Polygraphische Validierung von Ablenkmanövern in der klinischen Differentialdiagnose des Tremors

J. Spiegel,C. Heiss,E. Frühauf,W. Fogel,H. Meinck

DOI: https://doi.org/10.1007/s001150050358

1998-10-01

Der Nervenarzt

Abstract:

What problem does this paper attempt to address?

Fabrication of a Cation-Exchange Membrane Via the Blending of SPES/N-Phthaloyl Chitosan/MIL-101(Fe) Using Response Surface Methodology for Desalination

Xiaomeng Wang,Qun Wang,Mengjuan Zhao,Lu Zhang,Xiaosheng Ji,Hui Sun,Yongchao Sun,Zhun Ma,Jianliang Xue,Xueli Gao

DOI: https://doi.org/10.3390/membranes12020144

IF: 4.562

2022-01-01

Membranes

Abstract:In the present work, a novel mixed matrix cation exchange membrane composed of sulfonated polyether sulfone (SPES), N-phthaloyl chitosan (NPHCs) and MIL-101(Fe) was synthesized using response surface methodology (RSM). The electrochemical and physical properties of the membrane, such as ion exchange capacity, water content, morphology, contact angle, fixed ion concentration and thermal stability were investigated. The RSM based on the Box–Behnken design (BBD) model was employed to simulate and evaluate the influence of preparation conditions on the properties of CEMs. The regression model was validated via the analysis of variance (ANOVA) which exhibited a high reliability and accuracy of the results. Moreover, the experimental data have a good fit and high reproducibility with the predicted results according to the regression analysis. The embedding of MIL-101(Fe) nanoparticles contributed to the improvement of ion selective separation by forming hydrogen bonds with the polymer network in the membrane. The optimum synthesis parameters such as degree of sulfonation (DS), the content of SPES and NPHCs and the content of MIL-101(Fe) were acquired to be 30%, 85:15 and 2%, respectively, and the corresponding desalination rate of the CEMs improved to 136% while the energy consumption reduced to 90%. These results revealed that the RSM was a promising strategy for optimizing the preparation factors of CEMs and other similar multi-response optimization studies.
Preparation and Characterization of PVDF/nonwoven Fabric Flat-Sheet Composite Membranes for Desalination Through Direct Contact Membrane Distillation

Deyin Hou,Guohua Dai,Jun Wang,Hua Fan,Lin Zhang,Zhaokun Luan

DOI: https://doi.org/10.1016/j.seppur.2012.08.031

IF: 8.6

2012-01-01

Separation and Purification Technology

Abstract:The polyvinylidene fluoride (PVDF) flat-sheet composite membranes were prepared for membrane distillation using hydrophilic polyester nonwoven fabric as a support through coating and wet phase inversion process. The influence of non-solvent additive on membrane morphology, porosity, pore size and pore size distribution, hydrophobicity and permeability were evaluated. It was found that the membrane with a mixture of acetone and H3PO4 as non-solvent additive had a thinner top skin and a more porous network sponge-like layer from the morphology study. This membrane also exhibited a narrow pore size distribution and its mean pore size was about 0.22 mu m in diameter. The rough membrane surface with smaller nodules produced a higher contact angle of 82.6 +/- 0.7 degrees with water according to atomic force microscope images analysis. During the direct contact membrane distillation (DCMD) process of 35 g/L sodium chloride solution, the maximum transmembrane permeate flux about 47.6 kg/m(2) h was obtained with the feed solution at 80.5 degrees C and the cold distillate water at 20.0 degrees C. Furthermore, the membrane showed satisfying performance stability in the 240 h continuous desalination experiment, indicating that the prepared PVDF/nonwoven fabric flat-sheet composite membrane may be of great potential to be utilized in DCMD process for desalination. (c) 2012 Elsevier B.V. All rights reserved.
Evaluation of Anti‐wetting Nano‐fumed silica/PVDF Hollow Fiber Membrane by Central Composite Design Optimization Towards Efficient Desalination Performance via Membrane Distillation

Mohammed K. Alsebaeai,Abdul Latif Ahmad,Boon Seng Ooi

DOI: https://doi.org/10.1002/jctb.7504

IF: 3.709

2023-08-28

Journal of Chemical Technology and Biotechnology

Abstract:Background Membrane distillation (MD) is considered a viable technology to overcome the issue of water scarcity by desalination of seawater. However, the application of MD has been severely restricted by membrane‐wetting phenomena. This study aims to optimize the desired mixed matrix hollow fiber (HF) membrane conditions that have anti‐wetting characteristics for efficient desalination. Response surface methodology (RSM) based on central composite design (CCD) was used to predict and optimize the permeate flux and salt rejection. The Combined effects of polymer (polyvinylidene fluoride, PVDF) concentration, nano‐fumed silica (NFS) particle loading, coagulation bath temperature (CBT), and air gap distance (AG), as well as their interactions in terms of desalination performance, have been investigated. Results The linear factors (NFS, CBT), the quadratic effects of all variables, as well as the interacting terms between (PVDF, NFS), (PVDF, CBT), and (NFS, CBT) had significant effects for both pure water and permeate fluxes (PWF, PF). For salt rejection (SR), only PVDF presented a linear effect, while a quadratic effect was obtained in (NFS, AG) and an interaction effect was obtained between PVDF and NFS. Under optimal conditions of PVDF (15.03 wt.%), NFS (1.21 wt.%), CBT (54.85 oC), and AG (9.9 cm), the optimal mixed matrix HF membrane demonstrated higher experimental average values for pure water and permeate fluxes reached up to 11.95 and 11.61 kg m−2 h−1 respectively, and an SR of 99.96% as compared to the pristine membrane. Conclusion Our research provides an efficient anti‐wetting NFS/PVDF mixed matrix HF membrane, indicating that the optimal membrane possesses a high potential for the direct contact membrane distillation (DCMD) process. This article is protected by copyright. All rights reserved.

engineering, chemical,biotechnology & applied microbiology, environmental,chemistry, multidisciplinary
Engineering High-Effective Antifouling Polyether Sulfone Membrane with P(Peg-Pdms-Kh570)@Sio2 Nanocomposite Via In-Situ Sol-Gel Process

Qinghua Zhang,Jingxian Jiang,Fan Gao,Guangfa Zhang,Xiaoli Zhan,Fengqiu Chen

DOI: https://doi.org/10.1016/j.cej.2017.03.105

IF: 15.1

2017-01-01

Chemical Engineering Journal

Abstract:In this work, an original amphiphilic copolymer P(PEG-PDMS-KH570) combined with SiO2 nanoparticles (SiO2 NPs) was utilized to prepare polyether sulfone (PES) nanocomposite ultrafiltration (UF) membrane with enhanced antifouling performance. The enrichment of the organic-inorganic modifier P(PEG-PDMSKH570)@SiO2 were realized at the same time as the formation of PES UF membrane via sol-gel non solvent induced phase separation (NIPS) process. The interaction between the copolymer P(PEG-PDMSKH570) and SiO2 NPs furnished a stable and effective antifouling PES UF membrane. Surface morphology, chemical composition characterization and wetting property measurements confirmed the segregation and distribution of the nanocomposite modifier. The multi-defense mechanism from fouling resistance to fouling release of the nanocomposite membranes was investigated by setting bovine serum albumin (BSA) aqueous solution as a model foulant. The antifouling properties of the modified membranes, especially for the PES/T@SiO2 similar to 4% membrane, were effectively improved. The flux decline rate of PES/T@SiO2 similar to 4% membrane was as low as 15.6%, and the flux recover ratio was up to 99.0%. Moreover, the modified membranes also possessed remarkable antifouling stability. Results of this work provide a facile method to construct a hierarchical and heterogeneous membrane surface that could achieve the multi defense mechanism in efficient water treatment. (C) 2017 Elsevier B.V. All rights reserved.
Optimization of PES/ZnO mixed matrix membrane preparation using response surface methodology for humic acid removal

Abdul Latif Ahmad,Abdullah Adnan Abdulkarim,Suzylawati Ismail,Ooi Boon Seng

DOI: https://doi.org/10.1007/s11814-015-0221-9

IF: 2.7

2016-01-20

Korean Journal of Chemical Engineering

Abstract:The application of response surface methodology (RSM) in preparation and optimization of membranes is important in order to reduce the effort and time needed to achieving an optimum performance. RSM was used to develop an optimum polyethersulfone (PES)/ZnO mixed matrix (MM) membrane for humic acid removal. The MMs were synthesized by dispersing various amounts of hydrophilic ZnO nanoparticles (NPs) into a solution containing PES, polyvinylpyrrolidone (PVP) and dimethylacetamide (DMAc). Flat sheet MM membranes were prepared via the phase inversion method using the central composite design (CCD). The effects of four preparation parameters, such as PES, ZnO, PVP weight percentages and solvent evaporation time, were investigated. Pure water flux (PWF), humic acid flux (HAF) and humic acid rejection (HAR) were selected as a model responses. It was shown that PES and PVP were mainly affected on both PWF and HAF. Furthermore, the interaction effect between PES and ZnO-NPs shows a significant effect on PWF, while the quadratic effects of both solvent’s evaporation time and ZnO-NPs weight percentage coupled with the interaction effect between PES and PVP weight percentage shows the most significant parameters that affects HAR. The optimization method was subjected to maximize all of the PWF, HAF and HAR. It was also determined that the optimized membrane can be synthesized from a solution containing 17.25 wt% PES, 3.62 wt% ZnO and 3.75 wt% PVP with 15 s of solvent evaporation time. The optimum values of PWF, HAF and HAR were 222.3 (L/m2 h), 94.7 (L/m2 h), and 96.34%, respectively. Thus, it can be concluded that the CCD technique is capable of optimizing PES-ZnO membrane performance.

engineering, chemical,chemistry, multidisciplinary
Enhanced antifouling and separation capabilities of polydopamine@Ce-MOF functionalized PES ultrafiltration membrane

Dana Kadadou,Thanigaivelan Arumugham,Lina Tizani,Shadi W. Hasan

DOI: https://doi.org/10.1038/s41545-024-00302-z

2024-02-09

Huanjing Kexue/Environmental Science

Abstract:Abstract The need for antifouling membranes is substantial due to fouling’s negative impact on the effectiveness and durability of ultrafiltration membranes. In recent times, Metal-Organic Frameworks (MOFs) have emerged as effective additives for crafting ultrafiltration (UF) membranes. However, to harness their benefits and mitigate their drawbacks, a well-considered approach is imperative. In this work, polyethersulfone (PES) UF membranes were tailored with polydopamine (PDA)-modified cerium (Ce)-MOF (PDA@Ce-MOF) to achieve satisfactory antifouling properties and to remove biological macromolecules such as bovine serum albumin (BSA) and humic acid (HA) from wastewater. The non-solvent induced phase separation (NIPS) method was used to simultaneously fabricate the membrane and modify it with different PDA@Ce-MOF concentrations ranging from 0.05 to 0.50 wt.%. Results showed significant improvements on the membrane’s morphology, hydrophilicity, porosity and pore size at 0.10 wt.% loading of PDA@Ce-MOF. The synergistic effect of the PDA and Ce-MOF on the membrane improved the pure water flux (337 L m −2 h −1 ) and filtration performance in the filtration of Bovine serum albumin (BSA) and humic acid (HA) reporting 145 L m −2 h −1 and 98% rejection, and 164 L m −2 h −1 and 88% rejection; respectively. Further, water-attracting functional moieties of PDA@Ce-MOF hindered the deposition of BSA protein on the membrane surface, resulting in an excellent flux recovery ratio (FRR) of ~87%, alongside mitigated irreversible fouling.
Fabrication of superhydrophobic PVDF membrane via catechol/polyamine co-deposition and SiO 2 nanoparticles for membrane distillation

Yang Jin,Zhizhen Wei,Xin Meng,Jun Li

DOI: https://doi.org/10.1016/j.jece.2023.110250

IF: 7.7

2023-06-03

Journal of Environmental Chemical Engineering

Abstract:Due to the societal development and population growth, the crisis regarding fresh water resources has become increasingly prominent. As a membrane separation technology, Membrane distillation (MD) has emerged as a widely used in the recovery and utilization of fresh water. However, membrane wetting and membrane fouling have hindered the further application of MD. To address these challenges, this work provides a method for fabricating a superhydrophobic composite PVDF membrane using catechol(CA)/polyethyleneimine(PEI) co-deposition, sol-gel growth of SiO 2 nanoparticles, and the grafting of long chain perfluorosilane. The surface average roughness of the superhydrophobic membrane was up to 113.04 nm under the optimum conditions. The contact angle of the modified membrane was up to 157.5°, and a sliding angle is 8.0°, confirming its conformity to the Cassie-Baxter model. In addition, the modified membrane not only improved fouling and wetting resistance but also maintained a water flux equivalent to that of the PVDF membrane membrane when treating feeds containing surfactant, organic pollutants, and high salinity. In conclusion, this study provides a simple and feasible method for preparing superhydrophobic modified membrane, which further improves the adaptability of MD process for complex feed systems.

engineering, chemical, environmental
Study of a poly(vinylidene fluoride)/hydrophobic silica sol hybrid hollow fiber membrane for treatment of produced water via direct contact membrane distillation

Lusi Zou,Yu Zhang,Jianjia Yu,Shangwen Zha,Rong Guan,Shufang Jiang

DOI: https://doi.org/10.1016/j.jwpe.2021.102345

IF: 7

2021-12-01

Journal of Water Process Engineering

Abstract:Direct contact membrane distillation (DCMD) has shown great promises in remediating high-salinity oilfield produced water (PW). In our previous work, a hydrophobic silica sol (Si-R) was successfully synthesized to engineer anti-wetting ability of poly(vinylidene fluoride) (PVDF) membrane. Here our research interest lies in customizing PVDF hollow fiber membrane (HFM) with desirable stability for treating challenging oilfield PW via a DCMD process. The PVDF/Si-R hybrid HFM was fabricated under an optimized spinning condition. It is found that the fabricated PVDF/Si-R HFM is sandwich-structured, consisting a highly porous and thick middle layer and small-size macrovoids of outer layer and inner layer with different pore geometry, and the unique sandwich structure endows the membrane with superior wetting resistance. The membrane characterization showed that the liquid entry pressure (LEP) and water contact angle (WCA) of the fabricated PVDF/Si-R HFM impressively reached up to 5.25 bar and 126°, respectively. As a result, the PVDF/Si-R HFM possessed a desirable performance in treating high-salinity oilfield PW in terms of wetting resistance and salt rejection. Specifically, with a 60 h continuous DCMD operation, the PVDF/Si-R membrane exhibited over 99.9% salt rejection with only 7% reduction in permeate water flux. Clearly, the synthesized hydrophobic Si-R is a favorable additive for enhancing the antiwetting ability of PVDF HFM to treat high-salinity oilfield PW via DCMD process.

engineering, chemical, environmental,water resources
Preparation of superhydrophobic PVDF composite membrane via catechol/polyamine co-deposition and Ag nanoparticles in-situ growth for membrane distillation

Zhizhen Wei,Yang Jin,Jun Li,Lianyu Jia,Yujing Ma,Ming Chen

DOI: https://doi.org/10.1016/j.desal.2022.115649

IF: 11.211

2022-05-01

Desalination

Abstract:Membrane distillation (MD) has gained widespread attention in desalination and wastewater treatment. However, membrane fouling and membrane wetting seriously hinder its further development and industrial application. This work provides a method for preparing superhydrophobic modified membranes for MD through mussel-inspired coating, in-situ growth of nanoparticles and modification of low surface energy substances. The copolymerization of catechol and polyethyleneimine produced a poly(catechol/polyamine) layer rich in catechol groups and amino groups, which realized the in-situ reduction of silver nanoparticles and constructed a micro-nano rough structure. The resulting superhydrophobic modified membrane with an average roughness of 314.78 nm has a static water contact angle of 151.6 ± 2.5° and a sliding angle of 9.6°. The superhydrophobic membrane showed a membrane flux increase of more than 20% compared with the pristine PVDF and exhibited stable membrane flux and high salt rejection (>99.9%) when processing saline feeds containing surfactants, oily substances, organic pollutants and high concentration salts, indicating the excellent anti-wetting and anti-fouling properties. The superhydrophobic modified membrane prepared in this study improves the adaptability of the MD process and provides a promising candidate for membrane modification methods for MD.

engineering, chemical,water resources
Development of antifouling nanofiltration membranes for separation of dye/salt mixture through incorporation of novel polyelectrolyte-decorated silica

Mohamadreza Nazari,Zahra Mohamadnia,Mahtab Sabeti

DOI: https://doi.org/10.1016/j.jwpe.2024.106575

IF: 7

2024-11-26

Journal of Water Process Engineering

Abstract:Various physical and chemical methods can improve hydrophilicity and prevent fouling in polyethersulfone (PES)-based nanofiltration membranes. Here, two additives containing hydrophilic polymer brushes were used to modify the hydrophilicity of PES membranes. First, the surface of mesoporous silica (MS) was modified with poly(2,3-epoxypropyl methacrylate) (P(EPMA)) and poly[2-(acryloyloxy)ethyl]trimethylammonium chloride (P(AEtMAC)) brushes using the surface-initiated atom transfer radical polymerization (SI-ATRP) method to prepare MS- g -P(EPMA-SO 3 ) and MS- g -P(AEtMAC) as additive. Various weight percentages of the additives from 0.05 to 0.2 wt% were used to fabricate PES-based membranes and by adding the polymer brushes, the hydrophilicity of PES-based membranes increased. The membrane containing 0.075 wt% of MS- g -P(AEtMAC) additive exhibited a higher water flux of 18.6 (L/m 2 .h) at 5 bars. The separation of Coomassie Brilliant Blue G-250 (CBB) and Congo Red (CR) dyes (100 mg/L) was investigated; all membranes rejected more than 99 % of both dyes. However, the PES/MS- g -P(EPMA-SO 3 ) membrane, M2, showed a rejection rate of 11.5, 6.1, and 5.1 % for Na 2 SO 4 , MgCl 2 , and NaCl, respectively. PES/MS- g -P(AEtMAC) membrane, M6, rejected Na 2 SO 4 , MgCl 2 , and NaCl at 6.2, 11.9, and 6.8 %, respectively. Finally, the constructed membranes demonstrated remarkable selectivity for dye/salt mixtures, indicating great potential for treating dye-containing wastewater.

engineering, chemical, environmental,water resources
Tannic Acid −3-Aminopropyltriethoxysilane (TA-APTES) Coated UHMWPE Membrane for DCMD

Jiayou Quan,Lingling Tang,Xinwei Wang,Junrong Yu,Zuming Hu

DOI: https://doi.org/10.1016/j.seppur.2024.128617

IF: 8.6

2024-01-01

Separation and Purification Technology

Abstract:Commercial flat sheet membranes have relatively low flux in membrane distillation. Here, a ultra -high molecular weight polyethylene (UHMWPE) composite membrane with high flux was prepared via thermally induced phase separation (TIPS) method for direct contact membrane distillation (DCMD). The UHMWPE membrane has low tortuosity (spherical structure) and low thickness to decrease the vapor mass transfer resistance. In addition, UHMWPE/decalin gel membrane washed in hot decalin (85 degree celsius) in order to increase the permeate flux, and the optimum membrane has the highest flux of 43.51 kg/(m 2 .h). In order to increase the anti -wetting properties of UHMWPE membranes, Tannic acid (TA) - 3-aminopropyltriethoxysilane (APTES) coating composed of abundant nanospheres is co -deposited on the surface of UHMWPE membrane to increase surface roughness. The subsequent fluorination process can decrease the surface energy and improve the anti -surfactant property. The optimum modified membrane has a water contact angle of 152.5 degrees , and the permeate flux is 31.04 kg/(m 2 .h). Moreover, the membrane has high rejection (99.98 %) and high water recovery (82.87 %) over 60 h testing for high salinity anionic dyeing wastewater.
Improved Antifouling Properties of Poly(Ether Sulfone) Membrane by Incorporating the Amphiphilic Comb Copolymer with Mixed Poly(Ethylene Glycol) and Poly(Dimethylsiloxane) Brushes

Fan Gao,Guangfa Zhang,Qinghua Zhang,Xiaoli Zhan,Fengqiu Chen

DOI: https://doi.org/10.1021/acs.iecr.5b02864

2015-01-01

Industrial & Engineering Chemistry Research

Abstract:In this study, a novel amphiphilic comb copolymer P(poly(ethylene glycol) (PEG)-r-poly(dimethylsiloxane) (PDMS)) with mixed hydrophilic and low surface energy side chains was synthesized by the free radical polymerization method. The microstructure of the synthesized amphiphilic copolymers was characterized by Fourier transform infrared (FTIR) and the nuclear magnetic resonance proton spectra (H-1 NMR). The copolymers were blended with poly(ether sulfone) (PES) to fabricate low-fouling ultrafiltration membranes through nonsolvent induced phase separation (NIPS). The surface distribution of the hydrophilic PEG segments and hydrophobic PDMS segments on the membranes via surface segregation during the NIPS process was confirmed by the X-ray photoelectron spectroscopy (XPS), the wetting property, and the surface energy measurements. The multidefense mechanisms from fouling resistant to fouling release for the membranes modified by amphiphilic copolymers P(PEG-r-PDMS) were investigated with bovine serum albumin (BSA) aqueous solution as a model foulant. The antifouling properties of the modified membrane, especially for membrane PES/P(PEG-r-PDMS)similar to 31.3% (M-4), was effectively improved in comparation with pure PES membrane (M-0). The flux decline rate of the membrane M-4 was as low as 15.6%, and the flux recover ratio was up to 96.6%. The modified membrane also possessed stable and durable antifouling properties after three cycles of BSA filtration and chemical washing. It is promising that the present study can offer an effective approach to construct a low fouling membrane in the application of wastewater treatment and water purification.
Hydrophobic Polyvinylidene Fluoride Membrane Modified with Silica Nanoparticles and Silane for Succinic Acid Purification Using Osmotic Distillation Process

Jun Ying Tan,Wei Lun Ang,Abdul Wahab Mohammad,,,

DOI: https://doi.org/10.17576/jkukm-2021-33(1)-10

2021-02-28

Jurnal Kejuruteraan

Abstract:Recently, osmotic distillation (OD) has emerged as an alternative process for the concentration and purification of heat sensitive components. However, OD performance was severely affected by membrane fouling and wetting, which could be minimized through membrane surface roughness creation and surface energy modification. This study incorporated silica nanoparticles and coated tridecafluro-1,1,2,2-tetrahydrooctyl-1-triethoxysilane at various concentration onto polyvinylidene fluoride (PVDF) membrane to improve its hydrophobicity, limiting the contact between foulants in feed solution and membrane surfaces. Generally, the addition of silica reduced the water contact angle (WCA) of the membrane, but the inclusion of silane had increased it. These membranes were then tested through OD with 1 wt% succinic acid feed solution and 50 wt% calcium chloride stripping solution. PVDF membranes that have been modified with 1 wt% silica nanoparticles and coated with 1:50 volume ratio silane solution achieved a transmembrane flux of 0.6019 kg/m 2 ⋅h, the highest flux among silanated membrane. This was due to the larger pore size retained after silanization. A rejection rate of 95.66% and above were achieved by the membranes fabricated in this study. Overall, PVDF membrane modified with silica and silane had been successfully utilized in OD process and shown potential as a concentration and purification process.
Chemical and surface engineered superhydrophobic patterned membrane with enhanced wetting and fouling resistance for improved membrane distillation performance

Hyung Kae Lee,Saikat Sinha Ray,Dao Thi Thanh Huyen,Wooseok Kang,Young-Nam Kwon

DOI: https://doi.org/10.1016/j.memsci.2021.119280

IF: 9.5

2021-07-01

Journal of Membrane Science

Abstract:<p>Application of membrane distillation (MD) is still in its emerging stage due to membrane wetting and fouling issues. In this study, an anti-wetting and anti-fouling superhydrophobic patterned membrane was prepared utilizing patterned templet surface and subsequent chemical modifications with fluorine-based polymer. A uniform patterned polyvinylidene fluoride-co-chlorotrifluoroethylene (PVDF-CTFE) membrane was prepared using a template having a specific surface structure. It was found that the patterned membrane with a hierarchical microstructure was more hydrophobic than that with a flat surface. Long-term performance of the patterned membrane was determined through direct contact membrane distillation (DCMD). Results showed that such patterned membrane exhibited wetting resistance for a longer time compared to a pristine membrane. However, the patterned membrane showed rapid flux decline during a fouling test due to deposition of foulants such as humic acid (HA), alginate acid (AA), and bovine serum albumin (BSA). To overcome the fouling issue, a patterned membrane was chemically modified with 1H, 1H-perfluorooctyl methacrylate (FOMA) known to possess a low surface energy. After surface modification with FOMA, the superhydrophobic patterned membrane showed good stability in terms of water flux and salt rejection for more than 7 days in DCMD without wetting or fouling issue. Results of this study indicates the capability of a superhydrophobic patterned MD membrane for generating maximum water flux with excellent anti-fouling and wetting resistance properties.</p>

engineering, chemical,polymer science
Membrane Distillation Hybrid Peroxydisulfate Activation toward Mitigating the Membrane Wetting by Sodium Dodecyl Sulfate

Minyuan Han,Ruixue Zhao,Jianchao Shi,Xiaobo Li,Daoling He,Lang Liu,Le Han

DOI: https://doi.org/10.3390/membranes12020164

IF: 4.562

2022-01-29

Membranes

Abstract:The fouling/wetting of hydrophobic membrane caused by organic substances with low-surface energy substantially limits the development of the membrane distillation (MD) process. The sulfate radical (SO4 ·−)-based advanced oxidation process (AOP) has been a promising technology to degrade organics in wastewater treatment, and peroxydisulfate (PDS) could be efficiently activated by heat. Thus, a hybrid process of MD-AOP via PDS activated by a hot feed was hypothesized to mitigate membrane fouling/wetting. Experiments dealing with sodium dodecyl sulfate (SDS) containing a salty solution via two commercial membranes (PVDF and PTFE) were performed, and varying membrane wetting extents in the coupling process were discussed at different PDS concentrations and feed temperatures. Our results demonstrated permeate flux decline and a rise in conductivity due to membrane wetting by SDS, which was efficiently alleviated in the hybrid process rather than the standalone MD process. Moreover, such a mitigation was enhanced by a higher PDS concentration up to 5 mM and higher feed temperature. In addition, qualitative characterization on membrane coupons wetted by SDS was successfully performed using electrochemical impedance spectroscopy (EIS). The EIS results implied both types of hydrophobic membranes were protected from losing their hydrophobicity in the presence of PDS activation, agreeing with our initial hypothesis. This work could provide insight into future fouling/wetting control strategies for hydrophobic membranes and facilitate the development of an MD process.

engineering, chemical,materials science, multidisciplinary,polymer science,chemistry, physical
Surface engineering for anti-wetting and antibacterial membrane for enhanced and fouling resistant membrane distillation performance

Saikat Sinha Ray,Raghav Dangayach,Young-Nam Kwon

DOI: https://doi.org/10.1016/j.cej.2020.126702

IF: 15.1

2021-02-01

Chemical Engineering Journal

Abstract:With the emergence of membrane fouling as a prominent issue in long-term MD performance, it has become imperative to manufacture superhydrophobic membranes with antibacterial properties. In this study, a novel superhydrophobic and antibacterial membrane is fabricated using trichloro(1H,1H,2H,2H-perfluorooctyl)silane (TPFOS) and titanium dioxide nanoparticles (TiO2-NPs) as chemical modifiers. The virgin PVDF membrane was pre-treated using PEG-co-PMAA, followed by plasma treatment, to enhance the COOH and OH groups on the top layer and promote formation of coordinate bonds on the membrane surface to TiO2. TPFOS was used to impart a superhydrophobic behavior to the titanium-enriched membrane surface. Membrane characteristics were investigated using SEM-EDS, FT-IR, AFM, XPS, porosimetry, and tensile strength analysis. The PVDF/PP-PT/Ti/Si (polyvinylidene difluoride/ coated PEG-co-PMAA-plasma treated/titanium nanoparticles/perfluorooctyl silane) composite membrane showed a superior contact angle of ~152° and a better self-cleaning ability than that of the pristine PVDF membrane. Plasma treatment of the membrane results in increasing the porosity of the membrane by the mechanism of polymer ablation. Furthermore, the superhydrophobic membrane displayed superior performance due to enhanced water flux and improved salt rejection over long-term DCMD operation. It also possessed excellent antibacterial properties, exhibiting a bacterial reduction of ~99% when tested against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). This investigation demonstrates a simple approach to design multifunctional membranes showing anti-wetting, anti-bio-fouling, self-cleaning, and robust characteristics in MD desalination operations.

engineering, chemical, environmental
Surface Modification of Polytetrafluoroethylene Hollow Fiber Membrane for Direct Contact Membrane Distillation through Low-Density Polyethylene Solution Coating

Mohamad Razif Mohd Ramli,Abdul Latif Ahmad,Choe Peng Leo

DOI: https://doi.org/10.1021/acsomega.0c05107

IF: 4.1

2021-02-09

ACS Omega

Abstract:Membrane distillation (MD) is an attractive technology for the separation of highly saline water used with a polytetrafluoroethylene (PTFE) hollow fiber (HF) membrane. A hydrophobic coating of low-density polyethylene (LDPE) coats the outer surface of the PTFE membrane to resolve membrane wetting as well as increase membrane permeability flux and salt rejection, a critical problem regarding the MD process. LDPE concentrations in coating solution have been studied and optimized. Consequently, the LDPE layer altered membrane morphology by forming a fine nanostructure on the membrane surface that created a hydrophobic layer, a high roughness of membrane, and a uniform LDPE network. The membrane coated with different concentrations of LDPE exhibited high water contact angles of 135.14 ± 0.24 and 138.08 ± 0.01° for membranes M-3 and M-4, respectively, compared to the pristine membrane. In addition, the liquid entry pressure values of LDPE-incorporated PTFE HF membranes (M-1 to M-5) were higher than that of the uncoated membrane (M-0) with a small decrease in the percentage of porosity. The M-3 and M-4 membranes demonstrated higher flux values of 4.12 and 3.3 L m–2 h–1 at 70 °C, respectively. On the other hand, the water permeation flux of 1.95 L m–2 h–1 for M-5 further decreased when LDPE concentration is increased.This article has not yet been cited by other publications.

chemistry, multidisciplinary
Amphiphobic electrospun PTFE nanofibrous membranes for robust membrane distillation process

Mengdi Xu,Jinxue Cheng,Xiongfei Du,Qiang Guo,Yan Huang,Qinglin Huang

DOI: https://doi.org/10.1016/j.memsci.2021.119876

IF: 9.5

2022-01-01

Journal of Membrane Science

Abstract:Membrane distillation (MD) has been identified as a promising technology to desalinate the saline wastewater owing to its unique advantages including its ability in treating hypersaline solutions, 100% (theoretical) solute rejection and mild operating conditions. However, polytetrafluoroethylene (PTFE) hydrophobic membranes used for MD process were prone to be wetted caused by fouling due to the amphiphilic organics in feed solution. Herein, we developed an effective approach to fabricate amphiphobic PTFE nanofibrous membrane with enhanced anti-wetting and anti-fouling. During which, polyacrylonitrile (PAN) fiber was co-electrospun into PTFE/PVA precursor membrane, and Stőber method was adopted for in-situ growing of SiO2 nanoparticles (SiNPs). After sintering, the SiNPs were fixed on the surface of PAN and PTFE fibers through chemical bonds and adhesive forces, respectively, which constructed membrane surface micro/nano structure. And then, the trimethoxy (1H,1H,2H,2H-heptadecafluorodecyl) silane (17-FAS) was used to fluorinate SiNPs. The prepared PTFE membrane exhibited strong amphiphobicity with water contact angle of 166.9° and oil contact angle of 134.5°. The amphiphobic PTFE membranes behaved a stable flux and excellent salt rejection during the 24h MD experiment in treating hypersaline solution, saline containing surfactant and oily saline. Also, the membranes showed excellent stability and reusability in the three cycles test, showing good application prospect in MD process, especially in the harsh environment.

engineering, chemical,polymer science
Surface functionalization of polytetrafluoroethylene membrane by polydopamine and quaternary ammonium compound for fouling mitigation in membrane distillation of secondary effluent

Yang Li,Bingxuan Ji,Ziyang Chen,Zhenghua Zhang

DOI: https://doi.org/10.1016/j.jece.2024.112893

IF: 7.7

2024-04-29

Journal of Environmental Chemical Engineering

Abstract:Considering the worldwide water scarcity issue, membrane distillation (MD) offers a promising solution for producing reclaimed water from secondary effluent generated by municipal wastewater treatment plants. However, prolonged operation of MD systems can result in membrane fouling, which impairs separation efficiency and shortens the membrane's lifespan. To overcome these challenges, novel surface-modified polytetrafluoroethylene (PTFE) membranes have been developed through a combination of polydopamine deposition and quaternary ammonium compound (QAC) grafting (named as PDQ membranes). The objectives of this preparation are to reduce the membrane hydrophobicity, impart anti-adhesive and bactericidal properties, and improve water permeability and antifouling performance in the MD system. In particular, the membrane coated by a QAC solution with the concentration of 40 mM (named as M3 membrane), achieved a flux of 47.0 LMH, surpassing the original PTFE membrane by 11.4%. During the long-term direct contact membrane distillation operation with the secondary effluent, the M3 membrane exhibited significantly superior antifouling capability than the PTFE membrane. Undergoing three runs of the MD process, the flux reduction of M3 was only 38.1%, whereas the flux of original PTFE membrane experienced a 71.4% decline. The PDQ membranes were also capable of providing stable distillate quality (over 40 h). Notably, the M3 demonstrated a high rejection capability, with an impressive removal efficiency of 96.9% for low molecular weight organics and 92.5% for humus-like substances. Additionally, the PDQ membrane exhibited good anti-bioadhesion and bactericidal properties. This study highlights the promising application potential of the PDQ membrane for fouling mitigation in water and wastewater treatment.

engineering, chemical, environmental
Enhanced Anti-Wetting and Anti-Fouling Properties of Composite PFPE/PVDF Membrane in Vacuum Membrane Distillation

Jun Pan,Fangli Zhang,Zhaohui Wang,Shi-Peng Sun,Zhaoliang Cui,Wanqin Jin,Omar Bamaga,Hani. Abulkhair,Mohammed Albeirutty,Enrico Drioli

DOI: https://doi.org/10.1016/j.seppur.2021.120084

IF: 8.6

2021-01-01

Separation and Purification Technology

Abstract:Composite hydrophobic PFPE/PVDF membranes were prepared by coating and UV-curing for vacuum membrane distillation (VMD). The water contact angle of PFPE/PVDF membrane reached 162.6 degrees, while the decrease in pore size in comparison to the original membrane was insignificant. The effects of organic and inorganic foulants (including humic acid, sodium silicate and calcium carbonate) on membrane performance were investigated. As for this PFPE coating layer, it had an active mitigation effect on the scaling behavior and almost no membrane wetting occurred. In particular, the organic migration across the membrane was completely prevented. Then the membrane cleaning process was conducted to prove the stability under long-term operation of composite membranes when deionized (DI) water was used as cleaning agent after repeated cycles of VMD treatment of 2 M NaCl feed solutions containing 200 mg/L humic acid (HA). The results of a 30-h test indicate that the salt rejection was kept at a high level, exceeding 99.99% and the recovery of MD flux was around 90% of the initial flux after the second cleaning cycle. The promising anti-fouling and anti-wetting performance of the composite PFPE/PVDF membranes provides a high potential for further development of these membranes for membrane distillation and membrane crystallization applications.

Polygraphische Validierung von Ablenkmanövern in der klinischen Differentialdiagnose des Tremors

Fabrication of a Cation-Exchange Membrane Via the Blending of SPES/N-Phthaloyl Chitosan/MIL-101(Fe) Using Response Surface Methodology for Desalination

Preparation and Characterization of PVDF/nonwoven Fabric Flat-Sheet Composite Membranes for Desalination Through Direct Contact Membrane Distillation

Evaluation of Anti‐wetting Nano‐fumed silica/PVDF Hollow Fiber Membrane by Central Composite Design Optimization Towards Efficient Desalination Performance via Membrane Distillation

Engineering High-Effective Antifouling Polyether Sulfone Membrane with P(Peg-Pdms-Kh570)@Sio2 Nanocomposite Via In-Situ Sol-Gel Process

Optimization of PES/ZnO mixed matrix membrane preparation using response surface methodology for humic acid removal

Enhanced antifouling and separation capabilities of polydopamine@Ce-MOF functionalized PES ultrafiltration membrane

Fabrication of superhydrophobic PVDF membrane via catechol/polyamine co-deposition and SiO 2 nanoparticles for membrane distillation

Study of a poly(vinylidene fluoride)/hydrophobic silica sol hybrid hollow fiber membrane for treatment of produced water via direct contact membrane distillation

Preparation of superhydrophobic PVDF composite membrane via catechol/polyamine co-deposition and Ag nanoparticles in-situ growth for membrane distillation

Development of antifouling nanofiltration membranes for separation of dye/salt mixture through incorporation of novel polyelectrolyte-decorated silica

Tannic Acid −3-Aminopropyltriethoxysilane (TA-APTES) Coated UHMWPE Membrane for DCMD

Improved Antifouling Properties of Poly(Ether Sulfone) Membrane by Incorporating the Amphiphilic Comb Copolymer with Mixed Poly(Ethylene Glycol) and Poly(Dimethylsiloxane) Brushes

Hydrophobic Polyvinylidene Fluoride Membrane Modified with Silica Nanoparticles and Silane for Succinic Acid Purification Using Osmotic Distillation Process

Chemical and surface engineered superhydrophobic patterned membrane with enhanced wetting and fouling resistance for improved membrane distillation performance

Membrane Distillation Hybrid Peroxydisulfate Activation toward Mitigating the Membrane Wetting by Sodium Dodecyl Sulfate

Surface engineering for anti-wetting and antibacterial membrane for enhanced and fouling resistant membrane distillation performance

Surface Modification of Polytetrafluoroethylene Hollow Fiber Membrane for Direct Contact Membrane Distillation through Low-Density Polyethylene Solution Coating

Amphiphobic electrospun PTFE nanofibrous membranes for robust membrane distillation process

Surface functionalization of polytetrafluoroethylene membrane by polydopamine and quaternary ammonium compound for fouling mitigation in membrane distillation of secondary effluent

Enhanced Anti-Wetting and Anti-Fouling Properties of Composite PFPE/PVDF Membrane in Vacuum Membrane Distillation