Abstract:OBJECTIVE Endoscope-assisted repair of craniosynostosis is a safe and efficacious alternative to open techniques. However, this procedure is challenging to learn, and there is significant variation in both its execution and outcomes. Surgical simulators may allow trainees to learn and practice this procedure prior to operating on an actual patient. The purpose of this study was to develop a realistic, relatively inexpensive simulator for endoscope-assisted repair of metopic and sagittal craniosynostosis and to evaluate the models' fidelity and teaching content. METHODS Two separate, 3D-printed, plastic powder-based replica skulls exhibiting metopic (age 1 month) and sagittal (age 2 months) craniosynostosis were developed. These models were made into consumable skull "cartridges" that insert into a reusable base resembling an infant's head. Each cartridge consists of a multilayer scalp (skin, subcutaneous fat, galea, and periosteum); cranial bones with accurate landmarks; and the dura mater. Data related to model construction, use, and cost were collected. Eleven novice surgeons (residents), 9 experienced surgeons (fellows), and 5 expert surgeons (attendings) performed a simulated metopic and sagittal craniosynostosis repair using a neuroendoscope, high-speed drill, rongeurs, lighted retractors, and suction/irrigation. All participants completed a 13-item questionnaire (using 5-point Likert scales) to rate the realism and utility of the models for teaching endoscope-assisted strip suturectomy. RESULTS The simulators are compact, robust, and relatively inexpensive. They can be rapidly reset for repeated use and contain a minimal amount of consumable material while providing a realistic simulation experience. More than 80% of participants agreed or strongly agreed that the models' anatomical features, including surface anatomy, subgaleal and subperiosteal tissue planes, anterior fontanelle, and epidural spaces, were realistic and contained appropriate detail. More than 90% of participants indicated that handling the endoscope and the instruments was realistic, and also that the steps required to perform the procedure were representative of the steps required in real life. CONCLUSIONS Both the metopic and sagittal craniosynostosis simulators were developed using low-cost methods and were successfully designed to be reusable. The simulators were found to realistically represent the surgical procedure and can be used to develop the technical skills required for performing an endoscope-assisted craniosynostosis repair.

An Effective Simulator for Intraoral Facial Skeletal Contour Surgeries

Pilot Evaluation of Silicone Surrogates for Oral Mucosa Simulation in Craniofacial Surgical Training

Evaluation of a high fidelity cleft alveolar bone graft simulator

A simulator for maxillo-facial surgery integrating cephalometry and orthodontia

Development of synthetic simulators for endoscope-assisted repair of metopic and sagittal craniosynostosis

Assessment of a novel patient-specific 3D printed multi-material simulator for endoscopic sinus surgery

Pilot Validation of a 3-Dimensional Printed Pituitary Adenoma, Vascular Injury, and Cerebrospinal Fluid Leak Surgical Simulator

Interdisciplinary 3D digital treatment simulation before complex esthetic rehabilitation of orthodontic, orthognathic and prosthetic treatment: workflow establishment and primary evaluation

A New Software Suite in Orthognathic Surgery : Patient Specific Modeling, Simulation and Navigation

Addressing the Pandemic Training Deficiency: Filling the Void with Simulation in Facial Reconstruction

Standardized Protocol for Virtual Surgical Plan and 3-Dimensional Surgical Template-Assisted Single-Stage Mandible Contour Surgery

Accuracy of Three-Dimensional Soft-Tissue Prediction Considering the Facial Aesthetic Units Using a Virtual Planning System in Orthognathic Surgery

Soft tissue prediction in orthognathic surgery: Improving accuracy by means of anatomical details

Evaluation of a 3D Printed Silicone Oral Cavity Cancer Model for Surgical Simulations

Efficacy evaluation of a high-precision simulator of posterior pharyngeal flap pharyngoplasty

Mandible Reconstruction Assisted by Preoperative Virtual Surgical Simulation

Perceptions regarding the use of a three‐dimensionally‐printed manufactured educational simulator for periodontal treatment of intraosseous and interradicular lesions

Virtual Reality and Three-Dimensional Printed Models Improve the Morphological Understanding in Learning Mandibular Sagittal Split Ramus Osteotomy: A Randomized Controlled Study

Accuracy of 3-dimensional soft tissue prediction for orthognathic surgery in a Chinese population

Craniomaxillofacial Surgery with Computer-generated Three-dimensional Solid Models

Training in Skull Base Endonasal Endoscopic Surgery: Development and Validation of a Novel Low-Cost Simulation with Animal Cadaveric Model