Effect of combination of explosion venting and chemical barrier on starch explosion suppression in a large scale connected vessels
Jianfei Ding,Xingqing Yan,Yichang Jiang,Chen Song,Fei Xiao,Jie Zou,Qi Zhang,Jianliang Yu
DOI: https://doi.org/10.1016/j.psep.2023.04.029
2023-04-30
Process Safety and Environmental Protection: Transactions of the Institution of Chemical Engineers, Part B
Abstract:The explosion of starch poses a potential threat to the process safety of food and energy enterprises in product processing and storage. To control explosion, a 5 m 3 columnar tank with a 10 m long connecting pipe at one end and a 700 mm diameter explosion vent at the other end was built as an experimental device. Combined controlled explosion experiments were conducted using a rupture disc with a static activation pressure of 10 kPa and a chemical barrier containing ABC powder with nitrogen as the driving gas to investigate the pressure and flame change characteristics inside the vessel and piping. The experimental results show that the maximum explosion pressure in the connected vessel without explosion venting is 41.21kPa and the maximum pressure rise rate is 5.20 bar/s. Explosion venting reduces the maximum explosion pressure and pressure rise rate in the vessel by 52.31 % and 21.92 %, respectively, and reduces the flame propagation speed in the pipeline, so that the chemical barrier device can effectively isolate the flame when the installation distance is more than 6 m. The N 2 and ABC dry powder two-phase explosion suppressant produced an effective inhibition effect through the physical effects of oxygen insulation, heat absorption, and thermal transmission weakening, as well as the chemical effect of eliminating explosive radicals. The explosion venting provides an initial defense by releasing any remaining pressure and heat of the explosion, while the chemical barrier provides a secondary layer of protection by extinguishing the flame and suppressing the explosion in the pipe to prevent further damage. This combination can greatly reduce the risk of equipment damage, injuries, and fatalities caused by explosions in industrial settings. Aluminum dust explosion venting experiments with static activation pressure ranging from 70 kPa to 280 kPa were conducted in the 20 L spherical chamber with venting diameters from 20 mm to 125 mm. For the case of high activation pressure, the maximum flame length in experiments is 1.64 m, which is close to the prediction of standard, while the maximum width is significantly smaller than the prediction. New fitting formulas in a laboratory scale for flame length and width are obtained, which provide a reference for venting safety area design, and the effect of activation pressure, dust concentration and venting area are taken into account. By the comparison, the external pressure prediction of EN14491 shows a good performance and NFPA68 has an opposite trend with experiments. Based on the experimental results, it is found that the the external pressure attenuation is inversely proportional to the distance, which is different with the coefficient of the distance suggested by the standard EN 14491. Through experiments and numerical simulation methods, the parameters of each flow field and their effects on dust explosion intensity under different ignition delay time in a 1 m 3 explosion vessel were quantitatively studied. The results showed that the explosion pressure and pressure rise rate of corn starch first increased and then decreased with increasing ignition delay time, and the maximum value were obtained when the ignition delay time is about 600 ms, which were 0.884 MPa and 17.9 MPa/s, respectively. The comparison between the numerical simulation and experiment proves the accuracy of simulation calculation. Furthermore, the turbulent distribution of airflow and particles before ignition was quantitatively studied. The particle distribution is gradually uniform after 300 ms, and the turbulent kinetic energy is in a low range. The root mean square velocity and average turbulent kinetic energy of the airflow are 3 m/s and 3.5 m 2 /s 2 at 600 ms. The effect of ignition location on the pressure characteristics of vented dust explosion was investigated in a 20 L chamber. For internal pressure, the proportion of the venting mixture with different ignition locations coupled with the wall quenching effect dominated the internal pressure curves. Besides, the maximum pressure rise rate was controlled by the residual amount of the fuel and induced turbulence. For external pressure, the ignition location dominated the delay time of the external explosion and the number of pressure peaks. Furthermore, the generation mechanism of pressure peaks was revealed by external pressure curves together with the visualization of the flow field. Eventually, it was found that both the internal and external maximum pressure with central ignition was larger than rear-end ignition and then the front-end. The corresponding dynamic mechanism was theoretically revealed, and a dimensionless prediction model for venting size and maximum external pressure was established. Thanks to their ability to simulate the travel be -Abstract Truncated-