CuAg nanoparticle/carbon aerogel for electrochemical CO 2 reduction

Wenbo Wang,Runqing Lu,Xinxin Xiao,Shanhe Gong,Daniel Kobina Sam,Bin Liu,Xiaomeng Lv

DOI: https://doi.org/10.1039/d1nj03540a

IF: 3.3

2021-01-01

New Journal of Chemistry

Abstract:A small sized CuAg heterostructure anchored by a silk fibroin-derived carbon aerogel exhibits electrocatalytic CO 2 -to-CO conversion.

chemistry, multidisciplinary

What problem does this paper attempt to address?

Ag-Cu aerogel for electrochemical CO2 conversion to CO

Wenbo Wang,Shanhe Gong,Jun Liu,Yang Ge,Jie Wang,Xiaomeng Lv

DOI: https://doi.org/10.1016/j.jcis.2021.03.120

IF: 9.9

2021-08-01

Journal of Colloid and Interface Science

Abstract:The current strategy of electrocatalytic CO2 reduction reaction (eCO2RR) to generate useful chemicals and hydrocarbons is supposed to effectively mitigate the greenhouse effect. The practical application for eCO2RR in aqueous solutions, however, still was encumbered by its high overpotential, low activity and poor selectivity due to CO2 mass transfer and intermediate stability. Electrocatalytic materials with reduced overpotential and high efficiency and selectivity are exploited for further development. Herein, Ag+ and Cu2+ precursors were co-reduced to generate Ag-Cu bimetallic aerogel after further freeze drying. Compared with Ag100 aerogel, the optimal Ag88Cu12 can effectively decrease overpotential, improve selectivity and current density, and keep electrochemical stability. At -0.89 V vs. RHE, the Faraday efficiency reached 89.40% and the CO partial current density of -5.86 mA cm-2 was obtained. The intrinsic property of metal aerogel (hydrophobic, hierarchical porous structure, conductivity), presence of rich grain boundaries and geometric effect and the introduction of Cu leading to improvement of adsorption between the catalyst and the *COOH intermediate in Ag88Cu12, contribute to the enhanced performance. Furthermore, the strategy of constructing metal aerogel will improve metal catalyst performance towards eCO2RR and pave way for further industrial applications.

chemistry, physical
Superaerophilic Copper Nanowires for Efficient and Switchable CO2 Electroreduction.

Yun Kuang

DOI: https://doi.org/10.1039/c8nh00259b

2018-01-01

Nanoscale Horizons

Abstract:Copper is one of the most efficient electrocatalysts for switchable carbon dioxide conversion, but the design of an advanced Cu-based catalyst with high selectivity while suppressing hydrogen evolution remains a great challenge. Herein, we use Cu nanowires (Cu NWs) as the starting materials and polytetrafluoroethylene (PTFE) as the surface modifier to make a superaerophilic electrode using a wettability control strategy. This strategy allows tuning of the selectivity of the CO2 reduction reaction (CO2RR) and a decrease of the hydrogen evolution rate simultaneously by facilitating the supply of CO2 reactants and inhibiting the adsorption of water (protons). The transferring point from a pinning to bursting state turned out to be the optimized condition leading to the highest CO2RR faradaic efficiency without significant interference of current density. The optimized superaerophilic Cu NW catalyst showed CO-selectivity with a Faraday efficiency of 71% at -0.4 V vs. RHE and HCOOH-selectivity with a Faraday efficiency of 68% at -0.6 V vs. RHE. Moreover, the accelerated gas and ion diffusion and homogenized reactions also avoided accumulative damage on the surface of the Cu NWs and enhanced the stability of the Cu catalyst. This wettability tuning strategy provides a facile and efficient way to optimize the gas and ion diffusion layers, therefore promoting the performance of the CO2RR. This strategy potentially can be extended to the design of other gas consumption electrocatalysts.
Cu/Cu2O Nanoparticles Supported on Vertically ZIF-L-Coated Nitrogen-Doped Graphene Nanosheets for Electroreduction of CO2 to Ethanol

Yatao Zhang,Miaomiao Chen,Jing Wang,Jindun Liu,Kai Li,Yangyang Zhang

DOI: https://doi.org/10.1021/acsanm.9b01935

2020-01-24

Abstract:Metal–organic framework (MOF)-derived nanomaterials provide outstanding catalytic activities for CO2 electroreduction due to their large surface area, tunable geometric structures, and controllable...

Chemistry,Environmental Science,Engineering,Materials Science
Silk fibroin-derived carbon aerogels embedded with copper nanoparticles for efficient electrocatalytic CO2-to-CO conversion

Shanhe Gong,Xinxin Xiao,Wenbo Wang,Daniel Kobina Sam,Runqing Lu,Yuanguo Xu,Jun Liu,Chundu Wu,Xiaomeng Lv

DOI: https://doi.org/10.1016/j.jcis.2021.05.054

IF: 9.9

2021-10-01

Journal of Colloid and Interface Science

Abstract:Metal-carbon matrix catalyst has attracted a great deal of interest in electrochemical carbon dioxide reduction reaction (CO2RR) due to its excellent electrocatalytic performance. However, the design of highly active metal–carbon matrix catalyst towards CO2RR using natural biomass and cheap chemical precursors is still under challenge. Herein, a self-assembly strategy, along with CO2 gas as acidifying agent, to fabricate silk fibroin (SF) derived carbon aerogels (CA) combining trace copper nanoparticles (SF-Cu/CA) is developed. Zinc nitrate was introduced as a pore-forming agent to further optimize the pore structure of the as-prepared catalysts to form SF-Cu/CA-1. The rich mesoporous structure and unique constitute of SF-Cu/CA-1 is conducive to exposed numerous active sites, fast electron transfer rate, and the desorption of *CO intermediate, thus leading to the electrocatalytic CO2RR of SF-Cu/CA-1 catalyst with an excellent current density of 29.4 mA cm−2, Faraday efficiency of 83.06% towards carbon monoxide (CO), high the ratio value of CO/H2 (19.58), and a long-term stability over a 10-hour period. This performance is superior to that of SF-Cu/CA catalyst (13.0 mA cm−2, <math>FECO</math>=58.43%, CO/H2 = 2.16). This work not only offers a novel strategy using natural biomass and cheap chemicals to build metal–carbon matrix catalyst for electrocatalytic CO2-to-CO conversion, but also is expected to promote the industrial-scale implementations of CO2 electroreduction.

chemistry, physical
Electronic and Geometric Structure Engineering of Bicontinuous Porous Ag–Cu Nanoarchitectures for Realizing Selectivity-Tunable Electrochemical CO2 Reduction

Wenjun Zhang,Chenhong Xu,Yi Hu,Songyuan Yang,Lianbo Ma,Lei Wang,Peiyang Zhao,Caixing Wang,Jing Ma,Zhong Jin

DOI: https://doi.org/10.1016/j.nanoen.2020.104796

IF: 17.6

2020-01-01

Nano Energy

Abstract:The electrochemical conversion of waste carbon dioxide into hydrocarbon fuels represent a promising strategy for clean and sustainable energy production. However, the design of outstanding electrocatalysts that can reduce CO2 in an efficient and selective manner is challenging, and the fundamental understanding on reaction mechanism is still limited. Herein, we report the preparation of self-supported Ag–Cu bimetallic catalysts with bicontinuous nanoporous geometries and adjustable compositions through an electrochemical anodizing/dealloying process of Ag52Cu39Sn9 alloy foil to exploit their performances in electrocatalytic CO2 reduction. By changing the compositions from Ag91Cu9 to Ag65Cu35, the variations in atomic arrangement and electronic structure around the active sites bring synergistic effects on the binding strength of different reaction intermediates, realizing tunable product selectivity from CO to formate at high Faradaic efficiencies. In-situ Raman analysis and density functional theory calculations confirm that as the Ag–Cu atomic ratio shifts, the variations of formation free-energies and desorption capacities of intermediates lead to different reaction pathways and final products. The findings in this study provide a promising route to modulate the atomic structures and improve the properties of electrocatalysts towards CO2 fixation.
Cu-Sn Aerogels for Electrochemical CO2 Reduction with High CO Selectivity.

Yexin Pan,Muchen Wu,Ziran Ye,Haibin Tang,Zhanglian Hong,Mingjia Zhi

DOI: https://doi.org/10.3390/molecules28031033

IF: 4.6

2023-01-01

Molecules

Abstract:This work reports the synthesis of CuxSny alloy aerogels for electrochemical CO2 reduction catalysts. An in situ reduction and the subsequent freeze-drying process can successfully give CnxSny aerogels with tuneable Sn contents, and such aerogels are composed of three-dimensional architectures made from inter-connected fine nanoparticles with pores as the channels. Density functional theory (DFT) calculations show that the introduction of Sn in Cu aerogels inhibits H2 evolution reaction (HER) activity, while the accelerated CO desorption on the catalyst surface is found at the same time. The porous structure of aerogel also favors exposing more active sites. Counting these together, with the optimized composition of Cu95Sn5 aerogel, the high selectivity of CO can be achieved with a faradaic efficiency of over 90% in a wide potential range (−0.7 V to −1.0 V vs. RHE).
Cu Nanoparticles Decorating N-Doped Erythrocyte-Shaped Carbon Nanostructures for Electrochemical CO 2 Reduction

Wenke Xie,Tiantian Yang,Na Tian,Xuan-He Liu,Jie Chen

DOI: https://doi.org/10.1021/acs.energyfuels.1c03823

2022-01-04

Abstract:Cu-based nanostructures are considered to be promising in catalyzing electrocatalytic CO2 reduction reaction (ECO2R). Nevertheless, it is still a challenge to overcome high overpotential and competitive hydrogen evolution reaction. Herein, we aimed to engineer the activity and selectivity of ECO2R by size regulation of Cu nanoparticles in an N-doped carbon matrix. Cu nanoparticles with a size of 64 nm decorating N-doped erythrocyte-shaped carbon nanostructures (CuNPs@N–C-2) were constructed. CuNPs@N–C-2-modified electrodes displayed large electrochemically active surface area, fast charge transfer, and fast ECO2R rates and therefore exhibited excellent electrocatalytic ECO2R performance. CuNPs@N–C-2 achieved a high FECO (99%) at −0.7 V and showed long-term electrochemical stability. The studies demonstrated that both the size of Cu nanoparticles and abundant Cu-Nx sites in the N-doped carbon matrix contributed to the outstanding ECO2R performance. This work offered a potential way to explore efficient Cu-based nanostructures for ECO2R to CO.

energy & fuels,engineering, chemical
Ultra-stable oxygen species in Ag nanoparticles anchored on g-C3N4 for enhanced electrochemical reduction of CO2

Shun Zhang,Zhenzhen Mo,Jie Wang,Huiling Liu,Peng Liu,Die Hu,Taixing Tan,Cheng Wang

DOI: https://doi.org/10.1016/j.electacta.2021.138831

IF: 6.6

2021-09-01

Electrochimica Acta

Abstract:Oxide-derived silver catalysts containing stable oxygen species have been proved to be efficient for the electrochemical reduction reaction of CO2 (CO2RR) due to their enhanced binding energy to *COOH intermediate. Here we developed a hydrothermal decomposition method to synthesize silver nanoparticles (NPs) supported on carbon nitride (Ag/g-C3N4) from silver oxide (Ag2O) precursor. The obtained Ag/g-C3N4 electrocatalyst is capable of producing CO at a low onset overpotential (190 mV), and exhibits a high Faraday efficiency (FE) up to 94.0% at –0.7 V vs RHE along with a mass activity of 45.7 mA/mg. The improved electrochemical performance is attributed to the ultra-stable oxygen species derived from the incomplete decomposition of Ag2O and coexisted with Ag NPs in the final Ag/g-C3N4 composite. The presence and durability of oxygen species were verified from transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Ag MNN Auger spectra, and temperature-programmed reduction (TPR) measurements. The strong interaction between Ag NPs and g-C3N4 substrate via the Ag-N bonding alters the rate-determining step (RDS) of CO2RR from the electron transfer (CO2 to*CO2 •− ) to the proton transfer (*CO2 •− to *COOH) process.

electrochemistry
Ligand‐free silver nanoparticles for CO2 electrocatalytic reduction to CO

Francesco Mattarozzi,Nienke Visser,Jan Willem de Rijk,Peter Ngene,Petra de Jongh

DOI: https://doi.org/10.1002/ejic.202200365

IF: 2.551

2022-09-11

European Journal of Inorganic Chemistry

Abstract:Silver‐based catalysts are attractive for electroreduction of CO2 to CO. To understand the electrocatalyst properties, a good control over the nanoparticle size is necessary. Herein, we report a strategy to synthesize highly dispersed, ligand‐free silver Ag nanoparticles supported on carbon. We demonstrate that the heat treatment atmosphere and carbon surface chemistry are crucial to control the Ag particle size in the 10‐30 nm range. Even at low silver loadings (0.099 m2Ag m‐2), Ag nanoparticles outperforms the bulk silver at low overpotentials, leading to a 23.5 % CO Faradaic efficiency at ‐1.2 V vs RHE. The Ag weight‐based activity of the catalysts scales with the inverse particle size, while the Ag surface‐specific activity is independent of the particle size in this range. The supported silver nanoparticles can produce a H2 to CO ratio of 2.9 to 1, interesting for further exploration of this type of catalysts for syngas synthesis.

chemistry, inorganic & nuclear
Hydrophobically Made Ag Nanoclusters with Enhanced Performance for CO2 Aqueous Electroreduction

Zhijie Wang,Tengfei Li,Qihao Wang,Anxiang Guan,Na Cao,Abdullah M. Al-Enizi,Lijuan Zhang,Linping Qian,Gengfeng Zheng

DOI: https://doi.org/10.1016/j.jpowsour.2020.228705

IF: 9.2

2020-01-01

Journal of Power Sources

Abstract:Silver-containing material is one of the efficient electrocatalysts in converting CO2 into CO, but competing hydrogen evolution reaction (HER) in aqueous solutions results in poor energy efficiency. Here, Ag-3 subnanoclusters with the structure sensitive to CO2 activation are in situ prepared by the cyclohexene oxidation. Hydrophobically modified Ag nanomaterials with an average particle size from 1.0 to 3.3 nm are waterrepulsive, organic-soluble, and composited of the Ag-3 cluster units, possessing the electron donation and strong chemical adsorption of CO2. In the electroreduction of CO2, a high mass activity about 10,200 A cm(-2) g(A)(g)(-1) is achieved for CO production at -1.4 V vs. reverse hydrogen electrode (RHE) on Ag nanoclusters with the external size of 1.9 nm, exhibiting 20 times higher than commercial Ag nanoparticles (diameters of 60-120 nm). Electrochemical tests in flow cells show an excellent mass activity of 55,000 A cm(-2) g(Ag)(-1) with a large current density of around 30 mA cm(-2) for the CO production at -0.71 V vs. RHE, much higher than the previously reported Ag catalysts. Hydrophobically made Ag-3 subnanoclusters facilitate the CO2 electroreduction to CO in aqueous solutions through accelerating the electron donation and suppressing the side reaction of water reduction.
Cu/Nb2O5 composite aerogel for CO2 hydrogenation to methanol: Construction of porous structure and abundant active interfaces

Yue Xin,Qi Li,Sanmei Wang,Sunpei Hu,Liangbing Wang

DOI: https://doi.org/10.1016/j.cej.2023.144289

IF: 15.1

2023-08-01

Chemical Engineering Journal

Abstract:Catalytic conversion of CO2 offers a promising method to mitigate the green-house gas and recycle CO2 into value-added chemicals. Cu-based aerogels hold the potential as high-performance catalysts due to the three-dimensional morphology, high porosity, and self-supporting skeletons. Herein, we successfully applied Cu/Nb2O5 composite aerogel into CO2 hydrogenation, which achieved high production rate and selectivity towards methanol. Further mechanism study demonstrated that abundant interfaces between Cu and Nb2O5 were formed throughout the porous networks of Cu/Nb2O5 aerogel, acting as the active sites for the adsorption, activation, and selective conversion of CO2. Besides, the production of methanol was via the formate pathway over Cu/Nb2O5. This work opens up an appealing approach for the design of efficient catalysts with rich active sites for hydrogenation of CO2.

engineering, chemical, environmental
Decoration of Ag nanoparticles on CoMoO4 rods for efficient electrochemical reduction of CO2

Schindra Kumar Ray,Rabin Dahal,Moses D. Ashie,Bishnu Prasad Bastakoti

DOI: https://doi.org/10.1038/s41598-024-51680-w

IF: 4.6

2024-01-18

Scientific Reports

Abstract:Hydrothermal and photoreduction/deposition methods were used to fabricate Ag nanoparticles (NPs) decorated CoMoO 4 rods. Improvement of charge transfer and transportation of ions by making heterostructure was proved by cyclic voltammetry and electrochemical impedance spectroscopy measurements. Linear sweep voltammetry results revealed a fivefold enhancement of current density by fabricating heterostructure. The lowest Tafel slope (112 mV/dec) for heterostructure compared with CoMoO 4 (273 mV/dec) suggested the improvement of electrocatalytic performance. The electrochemical CO 2 reduction reaction was performed on an H-type cell. The CoMoO 4 electrocatalyst possessed the Faraday efficiencies (FEs) of CO and CH 4 up to 56.80% and 19.80%, respectively at − 1.3 V versus RHE. In addition, Ag NPs decorated CoMoO 4 electrocatalyst showed FEs for CO, CH 4 , and C 2 H 6 were 35.30%, 11.40%, and 44.20%, respectively, at the same potential. It is found that CO 2 reduction products shifted from CO/CH 4 to C 2 H 6 when the Ag NPs deposited on the CoMoO 4 electrocatalyst. In addition, it demonstrated excellent electrocatalytic stability after a prolonged 25 h amperometric test at − 1.3 V versus RHE. It can be attributed to a synergistic effect between the Ag NPs and CoMoO 4 rods. This study highlights the cooperation between Ag NPs on CoMoO 4 components and provides new insight into the design of heterostructure as an efficient, stable catalyst towards electrocatalytic reduction of CO 2 to CO, CH 4 , and C 2 H 6 products.

multidisciplinary sciences
0D/1D Heterostructure for Efficient Electrocatalytic CO2-to-C1 Conversion by Ultra-Small Cluster-Based Multi-Metallic Sulfide Nanoparticles and MWCNTs

Xiang Wang,Xiao-Li Wang,Jing Lv,Zhou Wu,Jiaxu Zhang,Dandan Hu,Chaozhuang Xue,Dongsheng Li,Xing Zhu,Tao Wu

DOI: https://doi.org/10.1016/j.cej.2021.130045

IF: 15.1

2021-01-01

Chemical Engineering Journal

Abstract:Rationally constructed catalysts for efficiently converting CO2 into valuable carbonaceous fuels like CO and formate via electrochemical process are promising for decreasing the excessive emission of CO2. Thus, electrocatalysts with a large turnover frequency (TOF) for CO and formate are highly desirable. To this end, multimetallic nanoclusters (NCs) with unique electronic structure, large specific surface and abundant active sites are favorable theoretically. However, their structural complexity and challenging synthesis impede the application in CO2 electroreduction. Herein, negatively charged multi-metallic sulfide supertetrahedral NCs-based nanoparticles, containing Cu, Ga, In and Sn four metal components, were for the first time electrostatically self-assembled with positively charged multi-walled carbon nanotubes (MWCNTs) to fabricate a novel 0D/1D heterostructure that exhibits efficient CO2 electroreduction to C-1 products (CO + HCOOH) with high Faradaic efficiency (FE) (>80%), excellent TOF (5974.62 h(-1)) and good long-term stability (12 h). Besides, a ratio-tunable syngas (CO + H-2) (V-CO/V-H2: 0.1 similar to 2.73) and efficient electrochemical oxygen reduction reaction (ORR) could also be achieved for the hybrid catalyst. Comparative experiments figured out the favorable synergistic effects of co-existed Ga and In ions and enhanced interfacial charge-transfer were responsible for the promoted CO2 electroreduction activity.
Lowering *CO Affinity over Cu Nanoparticles for Enhanced Electrochemical CO 2 Conversion to Multi-Carbon Products at High Current Density

Ya Zhang,Qiang Zhou,Xiang-Yu Lu,Xiao-Yu Zhang,Feng Gong,Wei-Yin Sun

DOI: https://doi.org/10.31635/ccschem.024.202404245

2024-01-01

CCS Chemistry

Abstract:Direct electrochemical conversion of CO2 to multicarbon products over small -sized Cu nanoparticles (NPs) remains a significant challenge due to the strong binding affinity between *CO and Cu sites. Herein, we developed a facile route to synthesize stable Cu NPs with a size of ca. 3.0 nm anchored on zeolitic imidazolate framework-8 (ZIF-8) (Cu/ZIF-8) and found that the electronic state of Cu NPs is effectively modulated by ZIF-8, leading to enhanced C2+ product selectivity. Due to the electronic interaction between Cu NPs and ZIF-8, the Cu center exhibits an electron -deficient state, resulting in decrease of the d -band center, which lowers the *CO affinity and speeds up asymmetric *CO-*COH coupling. Compared to bare Cu NPs with a low C2+ faradaic efficiency (FE) of 18.8%, Cu/ZIF-8 achieves a much higher C2+ FE of 61.0%. Moreover, the peak value of C2+ partial current density for Cu/ZIF-8 is 279.4 mA cm(-2), which exceeds most of the reported Cu -based electrocatalysts. This work provides advanced insights for reasonable design of Cu sites to produce multicarbon products by utilizing a metal-organic framework to stabilize and regulate the binding affinity of intermediates on small-sized Cu NPs.
Ag-Precipitated CuO Nanospheres for Enhanced Electrochemical Reduction of CO2

Jinyun Xu,Ming Li,Liping Zhao,Guoqiang Zhong,Yu Zhang,Ziqi Zhang,Yu Sun,Xudong Hu,Zhe Peng,Yicong Wang,Chunming Zheng,Xiaohong Sun

DOI: https://doi.org/10.3390/su16145888

IF: 3.9

2024-07-11

Sustainability

Abstract:An electrochemical CO2 reduction reaction (CO2RR) is an effective way to reduce greenhouse gases by converting CO2 into high-value-added chemical products using electricity generated from renewable energy. In this paper, a Cu2O spherical catalyst was prepared by ascorbic acid reduction. The precipitated Cu-Ag spherical catalyst (P-CuO-Ag) was successfully prepared by calcining Cu2O-Ag with the introduction of an Ag component as the substrate. During the electrochemical reduction of CO2, the FE of the P-CuO-Ag catalyst for C2H4 at a potential of −1.1 V vs. RHE was as high as 39.8%, which was nearly twice that of the CuO catalyst, while the local current density JC2H4 for C2H4 reached 6 mA cm−2. The incorporation of Ag gives the spherical CuO catalyst higher electrochemical activity and better kinetic performance than the catalyst without Ag.

environmental sciences,environmental studies,green & sustainable science & technology
Ag Doped Au44 Nanoclusters for Electrocatalytic Conversion of CO2 to CO.

Shisi Tang,Jiayu Xu,Xu Liu,Yan Zhu

DOI: https://doi.org/10.1002/chem.202201262

2022-01-01

Chemistry - A European Journal

Abstract:A novel Ag doped Au-44(C10H9)(28) nanocluster (C10H10=1-ethynyl-2,4-dimethylbenzene) was synthesized, that is, Ag4+xAu40-x(C10H9)(28) (x <= 6), where four Ag positions located in the surface staple of the cluster have been determined, while six Au/Ag co-occupying positions have been found in the metal core of the cluster. The electronic configuration of Au-44(C10H9)(28) cluster is significantly disturbed by doping Ag atoms, hence promoting the electron transport capability. For the two-electron conversion reaction of CO2 to CO in electrochemical reduction of CO2, Ag doped Ag4+xAu40-x(C10H9)(28) catalyst exhibited higher effective activity and long-term stability than its counterpart Au-44(C10H9)(28) catalyst.
Bulk-immiscible CuAg alloy nanorods prepared by phase transition from oxides for electrochemical CO2 reduction

Yihong Yu,Di Wang,Yimeng Hong,Teng Zhang,Chuangwei Liu,Jing Chen,Gaowu Qin,Song Li

DOI: https://doi.org/10.1039/d2cc04789f

IF: 4.9

2022-01-01

Chemical Communications

Abstract:Combining Cu and Ag in an alloy state holds promise to serve as a tandem catalyst for electrocatalytic CO2 reduction, but is restricted by immiscibility in the bulk. Here, a far-from-equilibrium method is developed to synthesize CuAg alloy by electroreduction of Cu2Ag2O3 under a large cathodic overpotential. The alloy state of CuAg is conducive to the formation of C2+ molecules. A high formation rate of C2H4 of 159.8 μmol cm-2 h-1 is reached on the CuAg alloy nanorods, 2.3 times higher than that on pure Cu.

chemistry, multidisciplinary
In situ growth of Ag aerogels mediating effective electrocatalytic CO2 reduction and Zn-CO2 batteries

Wenbo Wang,Shanhe Gong,Runqing Lu,Haotian Wang,Jun Liu,Xiaofeng Zhu,Bin Liu,Xiaomeng Lv

DOI: https://doi.org/10.1016/j.ces.2023.119042

IF: 4.7

2023-10-01

Chemical Engineering Science

Abstract:Metal aerogels have outshined themselves in electrocatalysis, however, the brittle property has constrained their intrinsic activity by the traditional drop-coating method of electrode preparation. Herein, a rapid in-situ growth strategy to obtain porous Ag aerogels on conductive carbon cloth (Ag As/CC) working as free-standing electrode was designed for electrocatalytic CO2 reduction to CO. The preserved porous network structure of Ag aerogels with hydrophobic surface effectively inhibits the competing reaction of hydrogen evolution. The CO Faraday efficiency of 99.6%, mass activityCO of 23.33 mA mg−1, and Energy efficiencyCO of 59.85% were achieved at −1.0 V vs. RHE. Ag As/CC exhibits quick charge response ability with relaxation time constant of 0.04 s, and high mass transfer with Tafel slope of 59 mV dec−1. It also worked as the cathode to drive Zn-CO2 rechargeable battery with a peak power density of 2.16mW cm−2, to achieve electrocatalytic CO2 fixation and energy storage.

engineering, chemical
Ordered Ag Nanoneedle Arrays with Enhanced Electrocatalytic CO 2 Reduction via Structure-Induced Inhibition of Hydrogen Evolution

Qin Chen,Kang Liu,Yajiao Zhou,Xiqing Wang,Kuangzhe Wu,Hongmei Li,Evangelina Pensa,Junwei Fu,Masahiro Miyauchi,Min Liu,Emiliano Cortés

DOI: https://doi.org/10.1021/acs.nanolett.2c01853

IF: 10.8

2022-08-02

Nano Letters

Abstract:Silver is an attractive catalyst for converting CO(2) into CO. However, the high CO(2) activation barrier and the hydrogen evolution side reaction seriously limit its practical application and industrial perspective. Here, an ordered Ag nanoneedle array (Ag-NNAs) was prepared by template-assisted vacuum thermal-evaporation for CO(2) electroreduction into CO. The nanoneedle array structure induces a strong local electric field at the tips, which not only reduces the activation barrier for CO(2)...

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Nanoporous Intermetallic Cu 3 Sn/Cu Hybrid Electrodes as Efficient Electrocatalysts for Carbon Dioxide Reduction

Wu‐Bin Wan,Yi‐Tong Zhou,Shu‐Pei Zeng,Hang Shi,Rui‐Qi Yao,Zi Wen,Xing‐You Lang,Qing Jiang

DOI: https://doi.org/10.1002/smll.202100683

IF: 13.3

2021-07-26

Small

Abstract:Designing highly selective and cost-effective electrocatalysts toward electrochemical carbon dioxide (CO2) reduction is crucial for desirable transformation of greenhouse gas into fuels or high-value chemical products. Here, the authors report intermetallic Cu3Sn that is in situ formed and seamlessly integrated on self-supported bimodal nanoporous Cu skeleton (Cu3Sn/Cu) via a spontaneous alloying of Sn and Cu as robust electrocatalyst for selective electroreduction of CO2 to CO. By virtue of Sn atoms strengthening CO adsorption on Cu atoms, the intermetallic Cu3Sn has an intrinsic activity of ≈10.58 μA cm−2, more than 80-fold higher than that of monometallic Cu. By virtue of hierarchical bicontinuous nanoporous Cu architecture facilitating electron transfer and CO2 and proton mass transport and offering high specific surface areas for full use of electroactive Cu3Sn sites, the nanoporous Cu3Sn/Cu hybrid electrodes produce CO at a low overpotential of 0.09 V, and exhibit high partial current density of ≈15 mA cm−2geo at overpotential of 0.59 V, along with excellent stability and selectivity of 91.5% Faradaic efficiency. The outstanding electrochemical performance make them attractive alternatives to precious Au- and Ag-based electrocatalysts for building low-cost CO2 electrolyzers to selectively produce CO.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology

CuAg nanoparticle/carbon aerogel for electrochemical CO 2 reduction

Ag-Cu aerogel for electrochemical CO2 conversion to CO

Superaerophilic Copper Nanowires for Efficient and Switchable CO2 Electroreduction.

Cu/Cu2O Nanoparticles Supported on Vertically ZIF-L-Coated Nitrogen-Doped Graphene Nanosheets for Electroreduction of CO2 to Ethanol

Silk fibroin-derived carbon aerogels embedded with copper nanoparticles for efficient electrocatalytic CO2-to-CO conversion

Electronic and Geometric Structure Engineering of Bicontinuous Porous Ag–Cu Nanoarchitectures for Realizing Selectivity-Tunable Electrochemical CO2 Reduction

Cu-Sn Aerogels for Electrochemical CO2 Reduction with High CO Selectivity.

Cu Nanoparticles Decorating N-Doped Erythrocyte-Shaped Carbon Nanostructures for Electrochemical CO 2 Reduction

Ultra-stable oxygen species in Ag nanoparticles anchored on g-C3N4 for enhanced electrochemical reduction of CO2

Ligand‐free silver nanoparticles for CO2 electrocatalytic reduction to CO

Hydrophobically Made Ag Nanoclusters with Enhanced Performance for CO2 Aqueous Electroreduction

Cu/Nb2O5 composite aerogel for CO2 hydrogenation to methanol: Construction of porous structure and abundant active interfaces

Decoration of Ag nanoparticles on CoMoO4 rods for efficient electrochemical reduction of CO2

0D/1D Heterostructure for Efficient Electrocatalytic CO2-to-C1 Conversion by Ultra-Small Cluster-Based Multi-Metallic Sulfide Nanoparticles and MWCNTs

Lowering *CO Affinity over Cu Nanoparticles for Enhanced Electrochemical CO 2 Conversion to Multi-Carbon Products at High Current Density

Ag-Precipitated CuO Nanospheres for Enhanced Electrochemical Reduction of CO2

Ag Doped Au44 Nanoclusters for Electrocatalytic Conversion of CO2 to CO.

Bulk-immiscible CuAg alloy nanorods prepared by phase transition from oxides for electrochemical CO2 reduction

In situ growth of Ag aerogels mediating effective electrocatalytic CO2 reduction and Zn-CO2 batteries

Ordered Ag Nanoneedle Arrays with Enhanced Electrocatalytic CO 2 Reduction via Structure-Induced Inhibition of Hydrogen Evolution

Nanoporous Intermetallic Cu 3 Sn/Cu Hybrid Electrodes as Efficient Electrocatalysts for Carbon Dioxide Reduction