How should induced abortion rates be measured.

W. James

Abstract:

What problem does this paper attempt to address?

Selective Hydrogenation of Furfural to Furfuryl Alcohol Without External Hydrogen over N-doped Carbon Confined Co Catalysts

Ling Xu,Renfeng Nie,Xilei Lyu,Juncheng Wang,Xiuyang Lu

DOI: https://doi.org/10.1016/j.fuproc.2019.106205

IF: 8.129

2019-01-01

Fuel Processing Technology

Abstract:Non-noble metal catalyzed transfer hydrogenation of biomass using biomass-derived formic acid (FA) as hydrogen source is one of promising strategies for relieving fossil energy crisis. Since acidic FA would destroy and deactivate naked active sites, developing heterogeneous catalysts with stabilized structure and activity that are qualified in harsh conditions is highly desirable but challenging. Herein, mesoporous N-doped carbon encapsulated Co catalysts (Co-N-C) are synthesized through a facile carbonization of Co(phen)(2)(OAc)(2) with nano-MgO as porogen agent. After acid treatment, the optimized Co-N-C-700 (pyrolyzed at 700 degrees C) could afford full furfural (FAL) conversion as well as > 99% furfuryl alcohol (FOL) selectivity with only 3.5 equiv. FA at 150 degrees C for 6 h, exhibiting much superior performance than commercial Pd-, Pt- and Ru-based catalysts. Using molecular H-2 as hydrogen source not only affords low conversion but also leads to over-hydrogenation of FOL and generation of furfuryl formate (FF). This catalyst is very stable in acidic FA and could be recycled 5 times without deactivation or leaching. Co-N-C-700 is also capable for gram-scale transfer hydrogenation of FAL and is versatile for other aldehydes with > 90% yield of desired products. This work could promote the application of encapsulated Co-based catalysts for selective transformation of biomass in chemical industry.
Hydrogenolysis and Hydrodeoxygenation of Lignin in a Two-Step Process to Produce Hydrocarbons and Alkylphenols

Biqin Lin,Rongxuan Li,Riyang Shu,Chao Wang,Zhengdong Cheng,Ying Chen

DOI: https://doi.org/10.1016/j.joei.2019.05.004

IF: 6.47

2020-01-01

Journal of the Energy Institute

Abstract:Valuable fuels and chemicals production from biomass with high yields is always a big challenge in the energy utilization field. Herein, a two-step process for the catalytic conversion of lignin was proposed to form the fuels. In the first step, the depolymerization of lignin occurred efficiently via the hydrogenolysis reaction, resulting in 19.2% aromatic monomers under the catalysis of Pd/C and CrCl3. The catalysts exhibited a synergistic effect on the cleavage of β-O-4 bonds and the hydrogenation procedure, which prevented the condensation of intermediate products remarkably. Afterwards, the aromatic monomers were extracted out with octane solvent successfully (extraction degree 89.7%) and then used as a substrate in a second hydrodeoxygenation (HDO) step. Product mixture composed of 26.5% hydrocarbons (increased from 5.5%) and 49.7% alkylphenols (increased from 42.9%) were obtained after the HDO upgrading, which exhibited high potential to be used as fuels. This two-step approach is very promising to be a practical chemical engineering process for the fuel production from lignin.
Selective conversion of lignocellulosic biomass and its components into value-added furans over Al-based bimetals: Analytical Py-GC × GC/MS

Yi Lu,Yunwu Zheng,Rui He,Zhifeng Zheng

DOI: https://doi.org/10.1016/j.jaap.2022.105485

IF: 6

2022-05-01

Journal of Analytical and Applied Pyrolysis

Abstract:Furans is a versatile chemical family, developing enviromental-friendly methods to prepare furans and enhance the selectivity of high-value furans are of great significance. In present study, bio-based activated carbon supported Al-containing bimetals were devised to serve as solid acid catalysts for selective transformation lignocellulosic biomass and its components into valuable furans. Among the bimetallic catalysts, 2Al-4Zr/AC increased both the content of furans and the selectivity of 5-MFF, and the highest peak area% of furans and selectivity of 5-methylfurfural (5-MFF) were 88.6% and 44.5%, which were derived from the catalytic pyrolysis of glucose, and the counterparts from the catalytic pyrolysis of pine wood were 56.3% and 30.7%, respectively. In addition to 5-MFF, 2-methylfuran ( 2-MF), furfural (FF) and 2,5-dimetylfuran (DMF) were also included into major furans. In the catalytic pyrolysis process of lignocellulosic biomass, C6-based sugars were conducive to the production of 5-MFF, and C5-based sugars favored the formation of 2-MF and FF. Characterization with NH3-TPD, Pyridine-IR, N2 adsorption-desorption, XRD and XPS indicated that 2Al-4Zr/AC, with mild Lewis acidity and combined Brønsted acid sites, high surface area and micro-mesoporous structure, promoted both the dehydration of saccharides and the dehydrogenation of cyclopentanones to increase the content of furans. In the catalyst, the synergistic effect between Al species (including Al2O3, AlO(OH) and Al(OH)3) and Zr species (mainly ZrO2) played an important role in its catalytic activity, and Al species were the major contributor to its activity.

engineering, chemical,chemistry, analytical,energy & fuels
High production of furfural by flash pyrolysis of C6 sugars and lignocellulose by Pd-PdO/ZnSO4 catalyst

Qiaoqiao Zhou,Jinxing Gu,Jingwei Wang,Anthony De Girolamo,Sasha Yang,Lian Zhang

DOI: https://doi.org/10.1038/s41467-023-37250-0

IF: 16.6

2023-03-21

Nature Communications

Abstract:Abstract Furfural (C 5 H 4 O 2 ) is an important platform chemical for the synthesis of next-generation bio-fuels. Herein, we report a novel and reusable heterogeneous catalyst, Pd-PdO/ZnSO 4 with 1.1 mol% palladium (Pd), for the production of furfural by flash pyrolysis of lignocelluloses at 400 °C. For both dry and wet C6 cellulose and its monomers, the furfural yields reach 74–82 mol%, relative to 96 mol% from C5 xylan and 23–33 wt% from sugarcane bagasse and corncob. The catalyst has a well-defined structure and bifunctional property, comprising a ZnSO 4 support for the dehydration and isomerization of glucose, and a local core-shell configuration for metallic Pd 0 encapsulated by an oxide (PdO) layer. The PdO layer is active for the Grob fragmentation of formaldehyde (HCHO) from glucose, which is subsequently in-situ steam reformed into syn-gas (i.e. H 2 and CO), whereas the Pd 0 core is active in promoting the last dehydration step for the formation of furfural.

multidisciplinary sciences
Efficient and selective conversion of xylose to furfural over carbon-based solid acid catalyst in water-γ-valerolactone

Bingbing Qiu,Jicheng Shi,Wei Hu,Yanfang Wang,Donghui Zhang,Huaqiang Chu

DOI: https://doi.org/10.1016/j.energy.2024.130774

IF: 9

2024-02-01

Energy

Abstract:Hydrothermal liquefication of biomass to produce high-quality chemicals and liquid fuels is considered as a renewable and sustainable technology. Herein, a one-step hydrothermal method was used to prepare microcrystalline cellulose supported carbon-based catalyst PTA-BC with the activation factor of phosphotungstic acid. It was demonstrated by Py-FTIR, NH3-TPD and XPS that PTA-BC is not only rich in functional groups but also contains Brønsted acid sites (hydroxyl groups) and Lewis acid sites (CC, carboxyl groups). After experimental optimization, the optimum yield of furfural obtained from xylose catalyzed by PTA-BC was 81.02% at the reaction temperature of 180 °C and the reaction time of 20 min. The results show that PTA-BC contains –COOH, –OH and CC as catalytic sites and that the synergistic effect of these functional groups. The nature of the reaction solvent, appropriate reaction temperature and residence time are the main reasons for the good catalytic performance. This work provides a promising way for the synthesis of solid acid catalyst, which has a wide application prospect for the production of furfural.

energy & fuels,thermodynamics
Selective Activation of C–OH, C–O–C, or C═C in Furfuryl Alcohol by Engineered Pt Sites Supported on Layered Double Oxides

Yanru Zhu,Wenfang Zhao,Jian Zhang,Zhe An,Xiaodan Ma,Zhijun Zhang,Yitao Jiang,Lirong Zheng,Xin Shu,Hongyan Song,Xu Xiang,Jing He

DOI: https://doi.org/10.1021/acscatal.0c01276

IF: 12.9

2020-06-29

ACS Catalysis

Abstract:The selective activation of targeted bonds in biomass-derived furfural or furfuryl alcohol with complex chemical linkages (C–C/C–H/C–O, C═C/C═O, or C–O–H/C–O–C) is of great challenge for biomass upgrading, expecting well-defined catalyst and definite catalytically active sites. This work demonstrates an efficient targeted activation to C–OH, C–O–C, or C═C by engineering the structure of catalytic Pt sites, affording 2-methylfuran (2-MF), tetrahydrofurfuryl alcohol (THFA), or 1,2-pentanediol (1,2-PeD) as product in the hydroconversion of furfuryl alcohol. The catalytic Pt sites have been engineered as atomic Pt, coordination unsaturated Pt–Pt in atom-thick dispersion, or coordination unsaturated 3D Pt–Pt by tailoring the Pt dispersion (single atom, 2D cluster, or 3D cluster) on Mg and Al-containing layered double oxide (Mg(Al)O) support. The selective activation of C–OH, C–O–C, or C═C has been traced with the FT-IR spectra recorded surface reaction. On atomic Pt, C–O–H is easily activated, with the assistance of Mg(Al)O support, with O-terminal adsorption without affecting furan C–O and C═C. However, C═C in the furan ring is easier to be activated on coordination-unsaturated Pt–Pt in atom-thick dispersion, resulting in a step-by-step hydrogenation to generate THFA. On coordination-unsaturated 3D Pt–Pt, the hydrogenolysis of furan ring is favored, resulting in the cleavage of furan C–O to produce 1,2-PeD. Also, the Mg(Al)O supports derived from Mg and Al layered double hydroxides (LDHs) here also play a key role in promoting the selectivity to 1,2-PeD by providing basic sites.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acscatal.0c01276?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acscatal.0c01276</a>.Detailed experimental procedures, characterization, and catalytic test methods; XRD patterns, SEM and STEM images, catalytic tests, EXAFS fitting curves, FT-IR spectra recorded surface reactions, and TPD profiles; appendix of <sup>1</sup>H and <sup>13</sup>C NMR spectra, mass spectrum, and assignments of the absorption bands in FT-IR spectra (<a class="ext-link" href="/doi/suppl/10.1021/acscatal.0c01276/suppl_file/cs0c01276_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

chemistry, physical
Efficient catalytic conversion of lignocellulosic biomass into renewable liquid biofuels via furan derivatives

jianjian wang,xiaohui liu,bicheng hu,guanzhong lu,yanqin wang

DOI: https://doi.org/10.1039/c4ra04900d

IF: 4.036

2014-01-01

RSC Advances

Abstract:Efficient production and sequential utilization of furan derivatives will provide a promising approach towards achieving renewable liquid biofuels from biomass. This study aims to investigate the simultaneous production of furfural and 5-(hydroxymethyl) furfural (HMF) from biomass and further upgrade them into biofuels. Firstly, furfural and HMF are obtained together with high yields from a mixture of C5 (xylose) and C6 (glucose) sugars, or from lignocellulosic biomass, such as birch, cornstalk, pine, bagasse, and poplar in a tetrahydrofuran (THF)/H2O-NaCl biphasic system under mild conditions. The co-existence of C5/C6 sugars or impurities in lignocellulosic biomass has little influence on the simultaneous production of furfural and HMF. Then, the generated furfural and HMF in the upper organic phase are directly used as substrates without extra separation and purification processes, and efficiently upgraded to 2-methylfuran (MF) and 2,5-dimethylfuran (DMF), both of which are considered as promising renewable liquid biofuels with high-energy content. Hence, the seamless integration of lignocellulosic biomass into renewable liquid biofuels will accelerate our society moving towards a renewable transportation economy by utilizing cheap feedstocks, mild reaction conditions, and cost saving in separation and purification.
Alcohol formaldehyde resin solid acid catalytic conversion of biomass into furan compounds

Huangxian Zhang,Kun Yuan,Yichen Zou,Dayong Peng,Jian Kang,Jing Chen,Wanming Xiong,Zongde Wang

DOI: https://doi.org/10.1016/j.biombioe.2024.107274

IF: 5.774

2024-06-13

Biomass and Bioenergy

Abstract:The conversion of waste lignocellulosic biomass into biomass platform chemicals is very promising. In this work, a novel resin-based solid acid catalyst was obtained by condensation of furfuryl alcohol with furfural, and mild calcination and sulfonation process. Then it was used to convert sugars and biomass to obtain furan compounds. Results showed that the solid acid with a furfural to furfuryl alcohol molar ratio of 3:1 is an irregular mesoporous material, with a specific surface area of 134.18 m 2 /g and an acid content of 2.723 mmol/g, which is extremely stable below 200 °C. 82.2 % (from fructose), 15.8 % (from glucose), 10.0 % (from cellobiose) yields of 5-HMF and 35.5 % (from xylose) yield of furfural could be obtained at 160 °C for 2 h. It can be reused more than 5 times and can restore the best catalytic effect after re-sulfonation. Notably, in the catalytic conversion of rice husk, rice straw, camphor tree branch and leaves under typical reaction conditions, 5-HMF and furfural was in yields of 9.4–24.5 % and 20.3–47.9 %, respectively. Moreover, a 10 % water dropwise to solvent can effectively promote the catalytic conversion of biomass, while there is a significant inhibitory effect after it exceeds 20 %.

energy & fuels,biotechnology & applied microbiology,agricultural engineering
Valorization of Waste Lignocellulose to Furfural by Sulfonated Biobased Heterogeneous Catalyst Using Ultrasonic-Treated Chestnut Shell Waste as Carrier

Jianguang Liang,Jingjian Zha,Nana Zhao,Zhengyu Tang,Yucai He,Cuiluan Ma

DOI: https://doi.org/10.3390/pr9122269

IF: 3.5

2021-12-17

Processes

Abstract:Recently, the highly efficient production of value-added biobased chemicals from available, inexpensive, and renewable biomass has gained more and more attention in a sustainable catalytic process. Furfural is a versatile biobased chemical, which has been widely used for making solvents, lubricants, inks, adhesives, antacids, polymers, plastics, fuels, fragrances, flavors, fungicides, fertilizers, nematicides, agrochemicals, and pharmaceuticals. In this work, ultrasonic-treated chestnut shell waste (UTS-CSW) was utilized as biobased support to prepare biomass-based heterogeneous catalyst (CSUTS-CSW) for transforming waste lignocellulosic materials into furfural. The pore and surface properties of CSUTS-CSW were characterized with BET, SEM, XRD, and FT-IR. In toluene–water (2:1, v:v; pH 1.0), CSUTS-CSW (3.6 wt%) converted corncob into furfural yield in the yield of 68.7% at 180 °C in 15 min. CSUTS-CSW had high activity and thermostability, which could be recycled and reused for seven batches. From first to seventh, the yields were obtained from 68.7 to 47.5%. Clearly, this biobased solid acid CSUTS-CSW could be used for the sustainable conversion of waste biomasses into furfural, which had potential application in future.

engineering, chemical
Acid-Free Conversion of Cellulose to 5-(Hydroxymethyl)furfural Catalyzed by Hot Seawater

Xiangcheng Li,Yayun Zhang,Qineng Xia,Xiaohui Liu,Kaihao Peng,Sihai Yang,Yanqin Wang

DOI: https://doi.org/10.1021/acs.iecr.8b00443

2018-01-01

Industrial & Engineering Chemistry Research

Abstract:The conversion of cellulose from renewable biomass into the key platform chemical, 5-hydroxymethylfurfural (HMF), is of fundamental importance to the production of numerous bioproducts and biofuels. Various acidic catalysts have been developed for this process; however, most systems suffer from low efficiency and poor sustainability. Here, we report an acid-free conversion of cellulose into HMF in a biphasic system of tetrahydrofuran/concentrated seawater. The yield of HMF reached 48.6%, and this system has excellent reusability and sustainability. We found that the chloridions (Cl-) can promote the isomerization of glucose via a 1,2-hydride shift path and accelerate the dehydration of fructose, thus driving the selective formation of HMF. This simple system is capable of converting raw biomass to furfural and HMF with the lignin residues transformed into useful alkanes via a sequential catalytic upgrading, paving a new economic-viable pathway for the full valorization of lignocellulosic biomass.
Catalytic conversion of lignocellulosic biomass to fine chemicals and fuels

Chun-Hui Zhou,Xi Xia,Chun-Xiang Lin,Dong-Shen Tong,Jorge Beltramini

DOI: https://doi.org/10.1039/c1cs15124j

Abstract:Lignocellulosic biomass is the most abundant and bio-renewable resource with great potential for sustainable production of chemicals and fuels. This critical review provides insights into the state-of the-art accomplishments in the chemocatalytic technologies to generate fuels and value-added chemicals from lignocellulosic biomass, with an emphasis on its major component, cellulose. Catalytic hydrolysis, solvolysis, liquefaction, pyrolysis, gasification, hydrogenolysis and hydrogenation are the major processes presently studied. Regarding catalytic hydrolysis, the acid catalysts cover inorganic or organic acids and various solid acids such as sulfonated carbon, zeolites, heteropolyacids and oxides. Liquefaction and fast pyrolysis of cellulose are primarily conducted over catalysts with proper acidity/basicity. Gasification is typically conducted over supported noble metal catalysts. Reaction conditions, solvents and catalysts are the prime factors that affect the yield and composition of the target products. Most of processes yield a complex mixture, leading to problematic upgrading and separation. An emerging technique is to integrate hydrolysis, liquefaction or pyrolysis with hydrogenation over multifunctional solid catalysts to convert lignocellulosic biomass to value-added fine chemicals and bio-hydrocarbon fuels. And the promising catalysts might be supported transition metal catalysts and zeolite-related materials. There still exist technological barriers that need to be overcome (229 references).
Biorefinery Roadmap Based on Catalytic Production and Upgrading 5-Hydroxymethylfurfural

Qidong Hou,Xinhua Qi,Meinan Zhen,Hengli Qian,Yifan Nie,Chuanyunlong Bai,Shiqiu Zhang,Xinyu Bai,Meiting Ju

DOI: https://doi.org/10.1039/d0gc02770g

IF: 9.8

2021-01-01

Green Chemistry

Abstract:Biorefineries, which utilize lignocellulosic biomass as renewable energy source and sustainable carbon feedstock, are a promising solution to alleviate the excessive dependence on the depleting fossil resources and address climate change and other environmental problems. Owing to the recalcitrance and over-functionalized nature of biomass, the conversion of biomass into desirable products requires a series of complex deconstruction, catalytic conversion, separation and purification processes. In the biorefinery roadmap, 5-hydroxymethylfurfural (HMF) stands out as a bridge connecting biomass raw materials to alternative fuels, chemicals and materials, which can displace petroleum-derived products. This review describes the recent advances in the design and development of catalytic systems for the conversion of biomass and their constituent carbohydrates to HMF via hydrolysis, isomerization and dehydration reactions, and the upgrading of HMF towards polymer monomers, fine chemicals, fuel precursors, fuel additives, liquid fuels, and other platform chemicals via hydrogenation, oxidation, esterification, etherification, amination and aldol condensation reactions, with emphasis on how the catalysts, solvents and reaction conditions determine the reaction pathway and product selectivity. We also attempt to provide a conceptual framework on how to evaluate the actual reaction efficiency, reusability, and economic and technical feasibility of different catalytic systems and highlight the key research challenges to be addressed.
A Scalable Upgrading of Concentrated Furfural in Ethanol: Combining Meerwein–Ponndorf–Verley Reduction with in Situ Cross Aldol Condensation

Gang Li,Wenqian Jiao,Zhen Sun,Yang Zhao,Zhangping Shi,Yueer Yan,Lei Feng,Yahong Zhang,Yi Tang

DOI: https://doi.org/10.1021/acssuschemeng.7b04770

IF: 8.4

2018-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Currently, the catalytic upgrade of biomass-derived platform molecules into valuable chemicals is of great interest. In this work, an integrated route for upgrading concentrated furfural (17.3-80.5 wt %) in ethanol through the combination of Meerwein-Ponndorf-Verley reduction with in situ cross aldol condensation is developed, and the two valuable products, furfuryl alcohol and 3-(2-furyl)acrolein, are highly selectively obtained by using Zr-beta zeolite as Lewis acid catalyst and alkali metal carbonate as base catalyst. It is found that the efficient match of the two types of reactions plays a key role in upgrading furfural in this integrated process. Under optimal conditions, the highest conversion and mass conversion rate of furfural can reach up to 84.9% and 95.3 g.L-1.h(-1) respectively. This process also provides efficient separation of the two products by making use of their distinct solubilities in water.
Selective Electrocatalytic Hydrogenation of Lignocellulose-Derived 5-Hydroxymethylfurfural with Superior Productivities

Dingyi Zhang,Guanwu Lian,Wenbin Zhang,Zhousheng Mo,Henan Chen,Baiyao Liang,Yun Zhang,Wei Zhao

DOI: https://doi.org/10.1016/j.isci.2023.108003

IF: 5.8

2023-09-01

iScience

Abstract:Recently, valorization of biomass to value-added chemicals has drawn increasing attention due to carbon neutrality and sustainability. 5-Hydroxymethylfurfural is an important lignocellulose-derived biomass molecule. Herein, we have demonstrated the efficient electrocatalytic hydrogenation of 5-hydroxymethylfurfural to value-added 2,5-bis(hydroxymethyl)furan. An optimized electrolyzer with a highly electrolyte-permeable Pd cathode well balanced the selectivity, faradaic efficiency, and productivity. We have achieved high selectivity (97%) and faradaic efficiency (72%) at 50 mA cm−2 current density, and a record high productivity of 0.923 mmol cm−2·h−1 at 100 mA cm−2 current density, ∼2 times advanced compared with the best productivity in prior reports. We applied in situ infrared reflection-absorption spectroscopy to investigate the electrode-potential-dependent reaction pathways and mechanism, confirming that the highly selective hydrogenation of HMF is due to the tilted adsorption geometry through carbonyl group bonding to the surface of electrode. This work offers an opportunity for the sustainable electrocatalytic valorization of renewable lignocellulose-derived biomass with superior productivities approaching industrial level.

multidisciplinary sciences
Integrated catalytic process to directly convert furfural to levulinate ester with high selectivity

Bingfeng Chen,Fengbo Li,Zhijun Huang,Tao Lu,Yin Yuan,Guoqing Yuan

DOI: https://doi.org/10.1002/cssc.201300542

IF: 8.4

ChemSusChem

Abstract:Levulinic acid is an important platform molecule from biomass-based renewable resources. A sustainable manufacturing process for this chemical and its derivatives is the enabling factor to harness the renewable resource. An integrated catalytic process to directly convert furfural to levulinate ester was developed based on a bifunctional catalyst of Pt nanoparticles supported on a ZrNb binary phosphate solid acid. The hydrogenation of furfural and the following alcoholysis of furfuryl alcohol were performed over this catalyst in a one-pot conversion model. Mesoporous ZrNb binary phosphate was synthesized by a sol-gel method and had a high surface area of 170.1 m(2) g(-1) and a large average pore size of around 8.0 nm. Pt nanoparticles remained in a monodisperse state on the support, and the reaction over Pt/ZrNbPO4 (Pt loading: 2.0 wt%; Zr/Nb, 1:1) gave a very high selectivity to levulinate derivatives (91% in total). The sustainability of this conversion was greatly improved by the process intensification based on the new catalyst, mild reaction conditions, cost abatement in separation and purification, and utilization of green reagents and solvents.
Catalytic Conversion of Cellulose to 5‐Hydroxymethylfurfural: Advancements in Heterogeneous Catalysts and Cutting‐Edge Hydrolysis Strategies

Armin Rezayan,Yongsheng Zhang,Baojun Li,Chunbao Charles Xu,Chunbao (Charles) Xu

DOI: https://doi.org/10.1002/cctc.202300973

IF: 4.5

2023-08-30

ChemCatChem

Abstract:The catalytic conversion of lignocellulose‐derived carbohydrates, particularly cellulose, into 5‐hydroxymethylfurfural(HMF), holds significant potential as a crucial step in the sustainable production of valuable platform chemicals. This review presents the remarkable progress made in the field, with a specific emphasis on the role of heterogeneous catalysts, innovative methods for accelerating cellulose hydrolysis, and the design of flow reactor technologies. The distinctive properties and surface functionalities of catalysts facilitate the efficient breakdown of cellulose's intricate structure, promoting selective hydrolysis leading to HMF formation. Therefore, this review comprehensively examines various categories of heterogeneous catalysts, including metal‐oxides/phosphates, zeolites, functionalized silica/carbon‐based materials, heteropolyacids(HPAs), and metal‐organic‐frameworks(MOFs), highlighting their unique mechanisms and performance in cellulose conversion. Furthermore, the review describes the intriguing progress in hydrolysis strategies that have been crucially involved in overcoming the challenges associated with cellulose recalcitrance and achieving enhanced HMF yields. The synergistic interactions between catalysts and innovative hydrolysis methods have played a central role in the breakthroughs within cellulose conversion technology. Another aspect covered in this work is the advancement in using fixed‐/fluidized‐bed reactors and slug microreactors for the continuous production of HMF. Lastly, the current challenges and future perspectives are presented to propose the dilemma and development direction for efficient cellulose‐to‐HMF conversion.

chemistry, physical
Catalytic conversion of nonfood woody biomass solids to organic liquids

Katalin Barta,Peter C Ford

DOI: https://doi.org/10.1021/ar4002894

2014-05-20

Abstract:This Account outlines recent efforts in our laboratories addressing a fundamental challenge of sustainability chemistry, the effective utilization of biomass for production of chemicals and fuels. Efficient methods for converting renewable biomass solids to chemicals and liquid fuels would reduce society's dependence on nonrenewable petroleum resources while easing the atmospheric carbon dioxide burden. The major nonfood component of biomass is lignocellulose, a matrix of the biopolymers cellulose, hemicellulose, and lignin. New approaches are needed to effect facile conversion of lignocellulose solids to liquid fuels and to other chemical precursors without the formation of intractable side products and with sufficient specificity to give economically sustainable product streams. We have devised a novel catalytic system whereby the renewable feedstocks cellulose, organosolv lignin, and even lignocellulose composites such as sawdust are transformed into organic liquids. The reaction medium is supercritical methanol (sc-MeOH), while the catalyst is a copper-doped porous metal oxide (PMO) prepared from inexpensive, Earth-abundant starting materials. This transformation occurs in a single stage reactor operating at 300-320 °C and 160-220 bar. The reducing equivalents for these transformations are derived by the reforming of MeOH (to H2 and CO), which thereby serves as a "liquid syngas" in the present case. Water generated by deoxygenation processes is quickly removed by the water-gas shift reaction. The Cu-doped PMO serves multiple purposes, catalyzing substrate hydrogenolysis and hydrogenation as well as the methanol reforming and shift reactions. This one-pot "UCSB process" is quantitative, giving little or no biochar residual. Provided is an overview of these catalysis studies beginning with reactions of the model compound dihydrobenzofuran that help define the key processes occurring. The initial step is phenyl-ether bond hydrogenolysis, and this is followed by aromatic ring hydrogenation. The complete catalytic disassembly of the more complex organosolv lignin to monomeric units, largely propyl-cyclohexanol derivatives is then described. Operational indices based on (1)H NMR analysis are also presented that facilitate holistic evaluation of these product streams that within several hours consist largely of propyl-cyclohexanol derivatives. Lastly, we describe the application of this methodology with several types of wood (pine sawdust, etc.) and with cellulose fibers. The product distribution, albeit still complex, displays unprecedented selectivity toward the production of aliphatic alcohols and methylated derivatives thereof. These observations clearly indicate that the Cu-doped solid metal oxide catalyst combined with sc-MeOH is capable of breaking down the complex biomass derived substrates to markedly deoxygenated monomeric units with increased hydrogen content. Possible implementations of this promising system on a larger scale are discussed.
Increased high selectivity light aromatics and furans production by co-feeding methanol to catalytic pyrolysis of cellulose with Lanthanum-Cerium bimetallic modified MCM-41 catalysts

Feng Shi,Jida Wang,Hongyuan Wang,Can Liu,Yi Lu,Xu Lin,Defa Hou,Canling Wen,Shunxiong Yang,Cuiping Luo,Zhifeng Zheng,Yunwu Zheng

DOI: https://doi.org/10.1016/j.joei.2023.101206

IF: 6.47

2023-01-01

Journal of the Energy Institute

Abstract:To develop a cost-effective La-based catalyst for conversion waste biomass into high valuable chemicals, bimetallic La-Ce modified MCM-41 catalysts with different La to Ce ratios were prepared by wet impregnation method, and successfully applied to catalytic pyrolysis of cellulose with methanol as hydrogen-donor. The synergistic effect, conversion pathway for promotion of furans and aromatic and deactivation mechanism were also evaluated in co-conversion process with different technologies. Results showed that, modified MCM-41 maintained mesoporous structure, and combination La, Ce-modified MCM-41 catalysts showed the best catalytic activity due to synergistic interaction of La-O species and Ce-O species with support as well as suitable mild strong acidity. Higher La content had remarkable advantage for advancing HCs and olefin content due to higher Bronsted acid intensity, and higher Ce content was facilitated to aromatic and furans conversion due to higher mesoporous volume. 1La-3Ce/MCM-41 demonstrated the most potential for furan formation (50.18%) and 1La-1Ce/MCM-41 exhibited best deoxygenation activity and obtained more than 61.16% HCs content and 35.15% MAHs selectivity via Diels-Alder reaction assist with acid centers and metal dispersion, furthermore, 1La-1Ce/MCM-41exhibited outstanding reusability and anti-coking performance, nearly 95% yield of HCs were still maintained after regeneration. Hence, catalytic pyrolysis vapor upgrading of waste biomass with La-Ce/ MCM-41 had great potential to produce valuable fuels and chemical.
Lignin-MOF hybrid polymetallic composites for selective hydrogenolysis of cellulose derived 5-hydroxymethylfurfural

Jiantao Su,Fei Ge,Yidong Zhang,Minghao Zhou,Xin Zhao

DOI: https://doi.org/10.1016/j.jaap.2024.106706

IF: 6

2024-08-26

Journal of Analytical and Applied Pyrolysis

Abstract:The development of green, effective and inexpensive catalysts was important for the catalytic transfer hydrogenation of 5-hydroxymethylfurfural (HMF) to prepare 5-methylfurfuryl alcohol (MFA). The assembly of sodium lignosulfonate (LS) with NiCo-MOFs through a simple hydrothermal method was reported, and a series of iron-containing polymetallic hybrid catalysts were investigated. The introduction of iron led to the increase of medium strong acid sites and Lewis acid sites in the catalyst and enhanced the adsorption of furan rings, thus improved the catalytic activity. The effects of calcination temperature, iron content, and reaction parameters (including reaction temperature, pressure, hydrogen donor solvent) were all studied in detail. It was found that HMF could be completely converted over Fe@Ni 3 Co-MOF-LS, with a MFA yield of 88.75% under the optimal condition (240 °C, 2 MPa N 2 in 4 h) without the presence of hydrogen. This study provided a new perspective for the utilization of lignin resource as carbon-based catalysts for the production of biomass-derived platform chemicals.

engineering, chemical,chemistry, analytical,energy & fuels
Chemical transformations of 5-hydroxymethylfurfural to highly added value products: Present and future

Zhiwei Jiang,Yongjian Zeng,Di Hu,Ruichao Guo,Kai Yan,Rafael Luque

DOI: https://doi.org/10.1039/d2gc03444a

IF: 9.8

2022-11-25

Green Chemistry

Abstract:The synthesis of fuels, fuel additives, commercial and potential products from the platform molecules generated by the hydrolysis of the lignocellulosic biomass is a promising strategy toward the utilization of renewable feedstocks. Significant advances have been made on the various transformations (e.g., hydrogenation, oxidation, aldol-condensation, rehydration, amination, polymerization, etherification and decarbonylation) of biomass-derived 5-hydroxymethylfurfural (HMF). This review firstly gives an overview of these various transformations of HMF to produce a number of fuels as well as chemicals, wherein the fundamental aspects of reaction mechanisms, recent progress and challenges are highlighted, respectively. Different types of catalysts have also been summarized and compared in Tables. One objective is to comment the synthesis of value-added commercial and potential chemical (e.g., furan-based polyester platform 2,5-furandicarboxylic acid (FDCA), 5-hydroxymethyl-2-furancarboxylic acid (HMFCA), 2,5-diformylfuran (DFF)). Another purpose of the review is to comment fuels and fuel additives, including gasoline blendstock 2,5-dimethylfuran (DMF), ethyl levulinate (EL), gamma-valerlactone (GVL), methylfuran (MF) and so on. These obtained chemicals could replace the products from petrochemical resources, reducing the CO2 emission.

chemistry, multidisciplinary,green & sustainable science & technology

How should induced abortion rates be measured.

Selective Hydrogenation of Furfural to Furfuryl Alcohol Without External Hydrogen over N-doped Carbon Confined Co Catalysts

Hydrogenolysis and Hydrodeoxygenation of Lignin in a Two-Step Process to Produce Hydrocarbons and Alkylphenols

Selective conversion of lignocellulosic biomass and its components into value-added furans over Al-based bimetals: Analytical Py-GC × GC/MS

High production of furfural by flash pyrolysis of C6 sugars and lignocellulose by Pd-PdO/ZnSO4 catalyst

Efficient and selective conversion of xylose to furfural over carbon-based solid acid catalyst in water-γ-valerolactone

Selective Activation of C–OH, C–O–C, or C═C in Furfuryl Alcohol by Engineered Pt Sites Supported on Layered Double Oxides

Efficient catalytic conversion of lignocellulosic biomass into renewable liquid biofuels via furan derivatives

Alcohol formaldehyde resin solid acid catalytic conversion of biomass into furan compounds

Valorization of Waste Lignocellulose to Furfural by Sulfonated Biobased Heterogeneous Catalyst Using Ultrasonic-Treated Chestnut Shell Waste as Carrier

Acid-Free Conversion of Cellulose to 5-(Hydroxymethyl)furfural Catalyzed by Hot Seawater

Catalytic conversion of lignocellulosic biomass to fine chemicals and fuels

Biorefinery Roadmap Based on Catalytic Production and Upgrading 5-Hydroxymethylfurfural

A Scalable Upgrading of Concentrated Furfural in Ethanol: Combining Meerwein–Ponndorf–Verley Reduction with in Situ Cross Aldol Condensation

Selective Electrocatalytic Hydrogenation of Lignocellulose-Derived 5-Hydroxymethylfurfural with Superior Productivities

Integrated catalytic process to directly convert furfural to levulinate ester with high selectivity

Catalytic Conversion of Cellulose to 5‐Hydroxymethylfurfural: Advancements in Heterogeneous Catalysts and Cutting‐Edge Hydrolysis Strategies

Catalytic conversion of nonfood woody biomass solids to organic liquids

Increased high selectivity light aromatics and furans production by co-feeding methanol to catalytic pyrolysis of cellulose with Lanthanum-Cerium bimetallic modified MCM-41 catalysts

Lignin-MOF hybrid polymetallic composites for selective hydrogenolysis of cellulose derived 5-hydroxymethylfurfural

Chemical transformations of 5-hydroxymethylfurfural to highly added value products: Present and future