Abstract:Recently, the polymer solar cells (PSCs) based on the PM6 and small molecular acceptor (SMA) Y6 have attracted considerable attention in this community for their outstanding photovoltaic performance. As well known, the molecular weight of polymer has dramatic impact on the blend morphology and photovoltaic performance in the polymer solar cells, especially for those polymers with temperature‐dependent aggregation (TDA) behavior. In this work, a series of PM6 polymers with different weight‐average molecular weights (Mw= 41, 67, 74, 84 and 114 kDa) were synthesized, and the effects of the Mw on the morphology and photovoltaic performance were systematically investigated. Notably, tuning the molecular weight induces dramatic influences on the aggregation behaviors of the polymers and their corresponding blend morphology, which were explored by the temperature‐dependent UV‐vis absorptions (TD‐Abs), grazing incidence wide‐angle X‐ray scattering (GIWAXS) and resonant soft X‐ray scattering(R‐SoXS) measurements. Increasing Mw promoted the strong face‐on molecular packing and reduced the blend film domain sizes for enhanced donor‐acceptor interfacial areas, resulting in increased short‐circuit current densities (Jsc) and fill factor (FF). However, polymer donor with high Mw value processed stronger tendency of forming excessive pure donor aggregate, which hampered forming the intermixed phase for efficient charge transport, resulting in the inferior FF. Therefore, the optimized OSCs based on PM6 with moderate molecular weight (Mw=74 kDa) and Y6 exhibited suitable size and purity of the domains, facilitating well‐balanced charge transport, reducing trap‐assisted recombination and leading to significant enhancement of photovoltaic performance with the optimal PCE of 17.1%. This work indicates that proper and precisely tuning the molecular weight of polymer donor is critical to enhance the photovoltaic performance in PSCs.This article is protected by copyright. All rights reserved.

The Intrinsic Role of Molecular Mass and Polydispersity Index in High‐Performance Non‐Fullerene Polymer Solar Cells

Tuning Aggregation Behavior of Polymer Donor via Molecular‐Weight Control for Achieving 17.1% Efficiency Inverted Polymer Solar Cells

Effect of polymer molecular weight and processing solvent on the morphology and photovoltaic performance of inverted non-fullerene solar cells

Realizing the efficiency-stability balance for all-polymer photovoltaic blends

MORPHOLOGIES AND PERFORMANCE OF ORGANIC SOLAR CELLS USING LOW POLYMERIZATION DEGREE ALTERNATING COPOLYMER

High-Performance Additive-/Post-Treatment-Free Nonfullerene Polymer Solar Cells Via Tuning Molecular Weight of Conjugated Polymers.

Optimization Requirements of Efficient Polythiophene:Nonfullerene Organic Solar Cells

In Situ Monitoring Drying Process to Disclose the Correlation Between the Molecular Weights of a Polymer Acceptor with a Flexible Spacer and the Performance of All-Polymer Solar Cells

Over 18% efficiency of all‐polymer solar cells with long‐term stability enabled by Y6 as a solid additive

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Progress in Poly (3‐hexylthiophene) Organic Solar Cells and the Influence of Its Molecular Weight on Device Performance

Rational design of conjugated side chains for high-performance all-polymer solar cells

Polymerizing M‐Series Acceptors for Efficient Polymer Solar Cells: Effect of the Molecular Shape

Fine‐Tuning Batch Factors of Polymer Acceptors Enables a Binary All‐Polymer Solar Cell with High Efficiency of 16.11%

Comparing the Device Physics, Dynamics and Morphology of Polymer Solar Cells Employing Conventional PCBM and Non-Fullerene Polymer Acceptor N2200

Influence of Processing Parameters and Molecular Weight on the Morphology and Properties of High‐Performance PffBT4T‐2OD:PC71BM Organic Solar Cells

Controlling Molecular Weight to Achieve High-Efficient Polymer Solar Cells With Unprecedented Fill Factor of 79% Based on Non-Fullerene Small Molecule Acceptor

Improving the Efficiency and Stability of Non-Fullerene Polymer Solar Cells by Using N2200 As the Additive

Achieving an Efficiency Exceeding 10% for Fullerene‐based Polymer Solar Cells Employing a Thick Active Layer Via Tuning Molecular Weight

Morphology Optimization Via Molecular Weight Tuning of Donor Polymer Enables All-Polymer Solar Cells with Simultaneously Improved Performance and Stability

End‐extended Conjugation Strategy to Reduce the Efficiency‐Stability‐Mechanical Robustness Gap in Binary All‐Polymer Solar Cells