Abstract:Mass spectrometry is widely used analytical technique due to its high specificity for analyte identification as well as its high sensitivity.A custom mass spectrometer instrument based on a cylindrical ion trap (CIT)was built and its working parameters were optimized.An electron ionization(EI)source was chosen for experimental simplic-ity and availability of standard EI spectral libraries.The custom designed CIT was con-sisted of a pair of endcap electrodes and a ring electrode(r0=1 0 mm,z0=8.9 7 mm).A high voltage RF signal which needed to be applied directly to the ring electrode to pro-duce appropriate quadrupole was initially created by an RF generator at low voltage.A power amplifier and a voltage amplifier circuit were used to amplify to an appropriate power level.The boundary ej ection method was used.An electron multiplier,a current amplifier and NI PCIe data acquire card made up the ion detection and data acquisition system.The EI source,CIT and electron multiplier (EM)were mounted in a rail which ensured they were aligned precisely.The software designed in LabVIEW controlled the timing of the whole system.Several MATLAB programs were written to perform post-processing operations on saved MS data files.In order to obtain the optimal working pa-rameters,different values of filament current,bias voltage of EI,background pressure, voltage on the EM detector and mass scan rate were tested in the vacuum chamber.The trends of spectral peak were obtained:1)Signal intensity increased with the heating current supplied to the EI source due to the increased electron emission at higher tem-perature;2)The bias voltage of EI affected the kinetic energy of ions.With the increas-ing of the voltage,the signal intensity increased.When the voltage increased to a cer-tain range,the intensity fluctuated.In most common EI sources,a kinetic energy of 70 V was used.So the bias voltage was set as 70 V;3)Both signal intensity and resolution increased when background pressure was increased from 1×10-4to 6×10-4Pa.When the pressure further increased,the performance decreased;4)Signal intensity was pro-portional to the voltage on the EM detector.Considering the signal intensity and the lifetime of EM,a voltage of 1.75 kV was used;5)Mass scan rate had influence on the signal intensity and resolution.When the scan rate was too fast,the various ions bunched together and increased the signal intensity but reduced the resolution.Slowing the scan rate caused the peaks to spread apart resulting in increased resolution.By using the optimized parameters,several experiments were carried out.The results showed that the mass spectrum was accurate and the resolution was about 300.The MS plat-form performed well which laid a foundation of further research.To further improve resolution,axial RF will be applied to the endcap electrode to perform resonance ej ection in the following work and based on this platform the operation method for high-pressure MS will be explored.

Experimental Validation of Comprehensive Calculation for High-Resolution Linear MALDI-TOF Mass Spectrometry

Characterization of Ion Transmission in UV-FAIMS by Incorporating Ion Recombination

Novel approach of mass calibration in MALDI/FTMS

Mass Spectrometry Imaging Using Dynamically Harmonized FT-ICR at Million Resolving Power: Rationalizing and Optimizing Sample Preparation and Instrumental Parameters

Advanced Mass Calibration and Visualization for FT-ICR Mass Spectrometry Imaging

FT-ICR Mass Spectrometry Imaging at Extreme Mass Resolving Power Using a Dynamically Harmonized ICR Cell with 1ω or 2ω Detection

Ultra-High Mass Resolving Power, Mass Accuracy, and Dynamic Range MALDI Mass Spectrometry Imaging by 21-T FT-ICR MS

Following the Ions Through a Mass Spectrometer with Atmospheric Pressure Interface: Simulation of Complete Ion Trajectories from Ion Source to Mass Analyzer.

Graph-Based Method for Calibration of High-Resolution Mass Spectra of Natural Organic Matter.

Numerical Analysis and Quantification of Transfer Efficiency Coupled with Capillary and Quadrupole Ion Guide in an API-MS System

Experimental and Simulation Investigation of Ion Transfer in Different Sampling Capillaries.

Response Surface Methodology As a New Approach for Finding Optimal MALDI Matrix Spraying Parameters for Mass Spectrometry Imaging

Resolving Power and Collision Cross Section Measurement Accuracy of a Prototype High-Resolution Ion Mobility Platform Incorporating Structures for Lossless Ion Manipulation.

Enhanced Resolution Triple-Quadrupole Mass Spectrometry for Fast Quantitative Bioanalysis Using Liquid Chromatography/Tandem Mass Spectrometry: Investigations of Parameters That Affect Ruggedness

Experimental and Computational Evaluation of Lipidomic In-Source Fragmentation as a Result of Postionization with Matrix-Assisted Laser Desorption/Ionization

High Mass Accuracy and High Mass Resolving Power FT-ICR Secondary Ion Mass Spectrometry for Biological Tissue Imaging

Research on Key Techniques of Cylindrical Ion Trap Mass Spectrometer and Parameters Optimization

A Linear Model for Measuring the Experimental Resolution, Minimum Detection Limit, and Accuracy of Common Analytical Techniques

Modeling the ionization efficiency of small molecules in positive electrospray ionization using molecular dynamics simulations

Multiple ion isolation and accumulation events for selective chemical noise reduction and dynamic range enhancement in MALDI imaging mass spectrometry

Modality Agnostic Model for Spatial Resolution in Mass Spectrometry Imaging: Application to MALDI MSI Data