Abstract:Ammonia (NH 3 ) is a fundamental feedstock for the global population not only for its wide use as fertilizer and chemical, but also for its potential as energy storage medium. Its synthesis at the industrial scale is based on the well-known Haber Bosch process, operating at high temperature (400-500°C) and high pressure (150-300atm), thus making it highly pollutant. Considering the global climate emergency, it is mandatory to develop a green ammonia synthesis that relies on milder conditions and may adopt renewable energy sources. The electrochemical synthesis, of NH 3 from N 2 and H 2 O at ambient conditions and using renewable energy driven electricity could be a promising approach. An efficient electrochemical ammonia synthesis however, is currently still lacking. The main reasons are the absence of adequate catalysts capable of dissociating the N 2 triple bond and the competition with the hydrogen evolution reaction (HER) at the cathode, since the required potential is close to that of nitrogen reduction reaction (NRR), required for the ammonia formation. There are some reaction models in the literature but it is commonly accepted that the dissociative adsorption of N 2 is the rate limiting step and extensive research has been done on nitrogen interaction with metal surfaces. Ru, Co, Bi, Au, Fe, Mo, etc based materials have been extensively tested for the green ammonia synthesis, but results are still conflicting also because a complete evaluation of environmental contaminations is still lacking. In this work we adopted as NRR catalyst Fe based nanoparticles on carbon cloth substrate via a simple and fast electroless deposition technique. We prepared a FeCl 3 solutions with different concentrations in the range 1-10mM and deposited a drop on (3x1.5) cm 2 samples of carbon cloth, on a hot plate, at 80°C. After evaporation of the water, the as deposited substrates were dipped in NaBH 4 solution while stirring. The catalyst morphology has been studied by Scanning Electron Microscopy (SEM), as a function of the concentration. Very small particles, with a size ranging from 10 to 70nm, were obtained with the most diluted solution. The cluster size increases with increasing FeCl 3 concentration in the solution, giving rise to strong coalescence effects and to the formation of a thicker and continuous layer in the case of the most concentrated solution. Scanning Transmission electron Microscopy (STEM) and Electron Energy Loss Spectroscopy (EELS) have been adopted to determine the composition. EELS spectra showed that the iron L-edge is that typical of Fe 3 O 4 materials. The electrochemical ability to reduce nitrogen, with the formation of ammonia, was evaluated in a standard two compartment cell, with a phosphate buffered solution (PBS 0.1M) adopting a Zirfon membrane as a gas separator. Ar or N 2 gas (both with a purity of 99.9999%) flowed in the cathode chamber after going through an acidic trap and a water trap, to be further purified. A rigorous protocol has been adopted to evaluate the ammonia production, including a two steps measurement of the environmental ammonia at the open circuit potential. The ammonia was measured by spectrophotometric analysis using the indophenol blue method. The electrochemical production of ammonia was obtained by chronoamperometry under constant voltage. For the iron-based catalysts, a very efficient activation procedure has been developed, based on cyclic voltammetry under N 2 flow. The activation process allows an improvement up to 10 times in the ammonia generation rate. Moreover, a strong correlation has been found between the particle size of the catalyst and its activity for NRR, with the best results achieved with the sample covered with nanoparticles, exhibiting also the highest electrochemical active area. Iron based nanoparticles showed excellent activity for NRR, with a faradaic efficiency of 15% at -0.35 V vs RHE and a maximum ammonia production rate of 85μg mg -1 cat h -1 . Acknowledgements:This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No101006941.

Tailored Metal‐Porphyrin Based Molecular Electrocatalysts for Enhanced Artificial Nitrogen Fixation to Green Ammonia

Bimetallic Ag3Cu Porous Networks for Ambient Electrolysis of Nitrogen to Ammonia

Metal-Based Electrocatalysts for Selective Electrochemical Nitrogen Reduction to Ammonia

Boosting Electrochemical Nitrogen Fixation by Mesoporous Rh Film with Boron and Sulfur Co-Doping

Recent Advances in Metal‐Organic Framework‐Based Nanomaterials for Electrocatalytic Nitrogen Reduction

Metal-porphyrin-based three-dimensional covalent organic frameworks for electrocatalytic nitrogen reduction

Hydrophobicity Tailoring of Ferric Covalent Organic Framework/MXene Nanosheets for High‐Efficiency Nitrogen Electroreduction to Ammonia

Tailor-made yolk-shell nanocomposites of star-shape Au and porous organic polymer for nitrogen electroreduction to ammonia

Heterogeneous Electrocatalysts Design for Nitrogen Reduction Reaction under Ambient Conditions

Fe‐based catalysts for nitrogen reduction toward ammonia electrosynthesis under ambient conditions

Highly Durable and Selective Fe- and Mo-Based Atomically Dispersed Electrocatalysts for Nitrate Reduction to Ammonia via Distinct and Synergized NO<sub>2</sub><SUP>-</SUP> Pathways

Highly Selective Electrochemical Reduction Of Dinitrogen To Ammonia At Ambient Temperature And Pressure Over Iron Oxide Catalysts

Interface hydrophobic tunnel engineering: A general strategy to boost electrochemical conversion of N2 to NH3

Development of Electrocatalysts for Efficient Nitrogen Reduction Reaction under Ambient Condition

Iron Based Catalysts for Nitrogen Reduction Reaction

Tandem electrocatalytic N2 fixation via proton-coupled electron transfer

Recent developments in heterogeneous electrocatalysts for ambient nitrogen reduction to ammonia: Activity, challenges, and future perspectives

Pendant Proton‐Relays Systematically Tune the Rate and Selectivity of Electrocatalytic Ammonia Generation in a Fe‐Porphyrin Based Metal‐Organic Framework

Tailoring of Three-Atom Metal Cluster Catalysts for Ammonia Synthesis

Boosting the Electrocatalytic Conversion of Nitrogen to Ammonia on Metal-Phthalocyanine-Based Two-Dimensional Conjugated Covalent Organic Frameworks

Electrochemical Ammonia Synthesis under Ambient Conditions using TM-embedded Porphine-Fused Sheets as Single-Atom Catalysts