Abstract:Recently, the polymer solar cells (PSCs) based on the PM6 and small molecular acceptor (SMA) Y6 have attracted considerable attention in this community for their outstanding photovoltaic performance. As well known, the molecular weight of polymer has dramatic impact on the blend morphology and photovoltaic performance in the polymer solar cells, especially for those polymers with temperature‐dependent aggregation (TDA) behavior. In this work, a series of PM6 polymers with different weight‐average molecular weights (Mw= 41, 67, 74, 84 and 114 kDa) were synthesized, and the effects of the Mw on the morphology and photovoltaic performance were systematically investigated. Notably, tuning the molecular weight induces dramatic influences on the aggregation behaviors of the polymers and their corresponding blend morphology, which were explored by the temperature‐dependent UV‐vis absorptions (TD‐Abs), grazing incidence wide‐angle X‐ray scattering (GIWAXS) and resonant soft X‐ray scattering(R‐SoXS) measurements. Increasing Mw promoted the strong face‐on molecular packing and reduced the blend film domain sizes for enhanced donor‐acceptor interfacial areas, resulting in increased short‐circuit current densities (Jsc) and fill factor (FF). However, polymer donor with high Mw value processed stronger tendency of forming excessive pure donor aggregate, which hampered forming the intermixed phase for efficient charge transport, resulting in the inferior FF. Therefore, the optimized OSCs based on PM6 with moderate molecular weight (Mw=74 kDa) and Y6 exhibited suitable size and purity of the domains, facilitating well‐balanced charge transport, reducing trap‐assisted recombination and leading to significant enhancement of photovoltaic performance with the optimal PCE of 17.1%. This work indicates that proper and precisely tuning the molecular weight of polymer donor is critical to enhance the photovoltaic performance in PSCs.This article is protected by copyright. All rights reserved.

Tuning the Molecular Weight of Chlorine‐Substituted Polymer Donors for Small Energy Loss †

Tuning Aggregation Behavior of Polymer Donor via Molecular‐Weight Control for Achieving 17.1% Efficiency Inverted Polymer Solar Cells

Multichloro-Substitution Strategy: Facing Low Photon Energy Loss in Nonfullerene Solar Cells

Chlorinated Polythiophene‐Based Donors with Reduced Energy Loss for Organic Solar Cells

Subtle Polymer Donor and Molecular Acceptor Design Enable Efficient Polymer Solar Cells with a Very Small Energy Loss

Chlorinated Benzo[1,2‐b:4,5‐c′]dithiophene‐4,8‐dione Polymer Donor: A Small Atom Makes a Big Difference

Reducing Energy Loss and Morphology Optimization Manipulated by Molecular Geometry Engineering for Hetero‐junction Organic Solar Cells

Chlorination of Conjugated Side Chains to Enhance Intermolecular Interactions for Elevated Solar Conversion

A Chlorinated Donor Polymer Achieving High‐Performance Organic Solar Cells with a Wide Range of Polymer Molecular Weight

Reduced Energy Loss Enabled by a Chlorinated Thiophene‐Fused Ending‐Group Small Molecular Acceptor for Efficient Nonfullerene Organic Solar Cells with 13.6% Efficiency

Optimized energy level, morphology and photophysical procedure boosted the photovoltaic performance in monochlorinated benzothiadiazole-based polymer donors

Modulating Chlorination Position on Polymer Donors for Highly Efficient Nonfullerene Organic Solar Cells

Chlorination Enabling a Low‐Cost Benzodithiophene‐Based Wide‐Bandgap Donor Polymer with an Efficiency of over 17%

Exciton dynamics and charge transfer in polymer with effects of chlorine substituents

Over 14% Efficiency in Polymer Solar Cells Enabled by a Chlorinated Polymer Donor

Understanding the effect of chlorine substitution in all-polymer solar cells

Wide Band-gap Two-dimension Conjugated Polymer Donors with Different Amounts of Chlorine Substitution on Alkoxyphenyl Conjugated Side Chains for Non-fullerene Polymer Solar Cells

Effect of polymer molecular weight and processing solvent on the morphology and photovoltaic performance of inverted non-fullerene solar cells

Alkylsilyl Fused Ring‐Based Polymer Donor for Non‐Fullerene Solar Cells with Record Open Circuit Voltage and Energy Loss

Chlorinated Narrow Bandgap Polymer Suppresses Non‐Radiative Recombination Energy Loss Enabling Perylene Diimides‐Based Organic Solar Cells Exceeding 10% Efficiency

Chlorination of Side Chains: A Strategy for Achieving a High Open Circuit Voltage over 1.0 V in Benzo[1,2-b:4,5-b′]dithiophene-Based Non-Fullerene Solar Cells