Abstract:A theoretical foundation for selecting corrosion-resistant materials is necessary to address the corrosion risks in complex oil and gas fields and tubing for CO 2 capture, utilization, and storage (CCUS). To achieve this, experiments were conducted using actual oilfield simulated formation water as the corrosive medium. Weight-loss corrosion tests and surface analysis methods were employed to investigate and compare the corrosion of four steel materials (C110, 3Cr, 5Cr, and 9Cr) in high mineralization, CO 2 , and trace H 2 S coexistence environments. The results show that all materials experience CO 2 -dominated corrosion under CO 2 and trace H 2 S conditions, with corrosion rates exceeding the controlled limit for oilfields (0.076 mm/y). The corrosion severity is classified as extremely severe, and the corrosion products mainly comprise a mixed carbonate of FeCO 3 and CaCO 3 . Both uniform and localized corrosion rates decrease gradually with increasing chromium content in the materials. The experimental study demonstrates that chromium has good corrosion resistance. The morphology of the corrosion product film transitions from irregular particles to rhombohedral blocks or flakes with increased chromium content. Carbon steel primarily forms Fe x Ca 1-x CO 3 corrosion products with a small amount of Fe 2 O 3 inclusion, while corrosion products in chromium-containing steel include Cr 2 O 3 , Cr(OH) 3 , Fe x Ca 1-x CO 3 , and Fe 2 O 3 . As the chromium content in the steel material increases, the content of Ca and Cl elements in the corrosion product film gradually decreases. These findings provide valuable insights into the corrosion behavior of different steel materials under the challenging conditions of high mineralization, CO 2 -rich, and trace H 2 S environments. They contribute to the theoretical basis for selecting suitable corrosion-resistant tubing materials for oil and gas operations, including CCUS, enabling the industry to mitigate corrosion risks effectively.

Impact of steel properties on the susceptibility to corrosion of weld mesh and mesh straps

Corrosion considerations in the capacity of welded wire mesh

Mechanical properties of steel mesh in anchor-mesh support for rocky tunnels

Corrosion Development of Carbon Steel Grids and Shear Connectors in Cracked Composite Beams Exposed to Wet-Dry Cycles in Chloride Environment.

Corrosion of Steel Embedded in Mortar and Concrete under Different Electrolytic Accelerated Corrosion Methods

Influence of Reinforcement Mesh Configuration for Improvement of Concrete Durability

Durability Properties of Steel Textiles and Bonding Properties at the Interface of Steel Textiles with Reinforced Mortar-Reinforced Concrete Systems

Corrosion Behaviour of Weld Metal of Ultra-High-Strength Steel Weldments in a Sodium Chloride Aqueous Solution

Effect of Corrosion and Post-Weld Treatment on the Fatigue Behavior of Multipass Robot GMAW Welds of S700MC Steel

Challenges and opportunities in corrosion of steel in concrete

The life span and influencing factors of metal mesh in artificial soil on railway rock-cut slopes in humid areas

Steel Bridge-Coating Systems and Their Environmental Impacts: Current Practices and Future Trends

The effect of acidification on hydrogen uptake and corrosion resistance of advanced high-strength steels

Design and Identification of High Performance Steel Alloys for Structures Subjected to Underwater Impulsive Loading

Corrosion behaviour of welded low-carbon steel in the Arctic marine environment

Steel reinforcement corrosion in strain hardening cementitious composites (SHCC): the role of multiple microcracks and surface impregnation

Electrochemical Characterization of Steel Bridge Welds under Simulated Durability Test

Effect of Microstructures on Corrosion of X80 Pipeline Steel in an Alkaline Soil

Study On The Electrochemical Behavior Of The Weldment For Spv50q Steel In H2s-Containing Environment

Unraveling the Impact of Cr Content on the Corrosion of Tubing Steel in High CO2 and Low H2S Environments

Behavior of Weathering Steel in Artificial Harsh Environment