Effects of Different Ratios of Fly Ash and River Sand on Mechanical Properties of Cemented Paste Backfill Materials

Jiang Li,Shenggen Cao,Yang Liu,Chiyuan Che,Changzheng Zhao,Shuyu Du,Kaifei Wang,Ruiting Ma

DOI: https://doi.org/10.1155/2024/7529543

IF: 1.843

2024-01-03

Advances in Civil Engineering

Abstract:The mechanical properties of cemented paste backfill (CPB) are crucial for stope safety. Some mining areas in the Yellow River basin face a shortage of coal gangue, and these areas have abundant river sand (RS) resources. The use of RS as a fine aggregate can optimize the particle gradation of the material and improve the strength of the material. The effects of different fly ash (FA) and RS ratios on uniaxial compressive strength (UCS), elastic modulus, and microstructure of CPB were studied using uniaxial compression test and scanning electron microscopy. The results showed that with increasing FA content, UCS gradually increased at 7 and 14 days of CPB. However, at 28 days, the UCS of CPB first increased and then decreased. When the FA content was 40%, UCS at 28 days of backfill material reached its highest value of 14.76 MPa. The elastic modulus decreased as FA content increased and reached its maximum value of 1.54 GPa when FA content was 40%. FA optimized particle composition, promoted hydration reaction, and improved CPB strength; however, when FA content was more than 40%, it hindered cement hydration, thus deteriorating UCS. Based on Weibull distribution and prepeak correction factor, a damage constitutive model was established to describe the stress–strain process of CPB under load. The results of this research will provide a theoretical and experimental basis for CPB engineering design.

construction & building technology,engineering, civil

What problem does this paper attempt to address?

The problem this paper attempts to address is:

In some mining areas of the Yellow River Basin, there is a shortage of coal gangue, while these regions have abundant river sand resources. By studying the effects of different proportions of fly ash (FA) and river sand (RS) on the uniaxial compressive strength (UCS), elastic modulus, and microstructure of cement paste backfill (CPB) materials, the aim is to optimize the particle gradation of CPB materials to improve their strength and mechanical properties. Specifically, the paper explores the following issues:

1. **The effect of the proportion of fly ash (FA) and river sand (RS) on the uniaxial compressive strength (UCS) of CPB materials**:
- The impact of different FA contents on UCS at 7 days, 14 days, and 28 days of curing time.
- The results show that with the increase of FA content, the UCS gradually increases at 7 days and 14 days, but at 28 days, the UCS first increases and then decreases. When the FA content is 40%, the UCS at 28 days reaches the highest value of 14.76 MPa.

2. **The effect of the proportion of fly ash (FA) and river sand (RS) on the elastic modulus of CPB materials**:
- With the increase of FA content, the elastic modulus first decreases, then increases, and finally decreases again. When the FA content is 40%, the elastic modulus reaches the maximum value of 1.54 GPa.

3. **The effect of the proportion of fly ash (FA) and river sand (RS) on the microstructure of CPB materials**:
- Using scanning electron microscopy (SEM) to observe the effect of different FA contents on the microstructure of CPB materials. The results show that an appropriate amount of FA can optimize the particle composition, promote hydration reactions, and improve CPB strength; however, excessive FA can hinder cement hydration, thereby reducing UCS.

4. **Establishing a damage constitutive model**:
- Based on the Weibull distribution and pre-peak correction factor, a damage constitutive model describing the stress-strain process of CPB materials under load was established. This model will provide theoretical and experimental basis for CPB engineering design.

Through the above research, the paper aims to provide scientific basis for the design and application of CPB materials, especially in mining areas with a shortage of coal gangue and abundant river sand resources. This not only helps to improve the mechanical properties of backfill materials but also promotes the recycling of solid waste resources and reduces environmental pollution.