Abstract:Consideration of a core and mantle configuration for individual grains is a prominent method to capture the grain size-dependence in the constitutive models for polycrystal material. The mantle represents a region of the grain volume near the grain boundary where mechanical deformation is influenced by the grain boundaries, while the core represents the inner region of the grain volume. The grain size-dependence is then realized by assigning a set of values for the mechanical properties in the mantle that are different from those of the core region. However, these values for the mechanical properties of the mantle region are typically chosen arbitrarily, guided solely by the quality of the agreement between a model's predicted stress-strain behavior with that obtained experimentally. In the present study, a physics-based method to develop the grain size-dependent crystal plasticity constitutive model on the core and mantle configuration for polycrystal materials is presented. The method is based on the assumption that any resistance to dislocation nucleation and motion in a material manifests as an increase in yield strength and a decrease in strain-hardening modulus, and the mutual relationship between yield strength and strain-hardening is an inherent material property that determines the plasticity of that specific material. Accordingly, the same single crystal plasticity constitutive model that describes the behavior of the material under loading can be used to capture the increased resistance to dislocation nucleation and motion in the grain boundary influence region. The physics-based modeling is facilitated by introducing a shear flow strain distribution in the phenomenological formulation and a pile-up of dislocation density distribution in the dislocation based formulation, such that, the resulting variations in the yield strength and the strain-hardening modulus are identical to that produced by the increased resistance in the grain boundary influence region. Thus, the increase in strength and the decrease in the strain-hardening modulus, determined as spatially varying local material properties in the mantle, are mutually related through the grain size-independent inherent plastic properties specific to the material. A simplified model that considers the grain boundary effect averaged over the grain volume is also developed under this general framework. Implementation of this simplified model is demonstrated by considering the case of a power law flow rule and a hyperbolic-secant hardening rule for the phenomenological formulation, and Taylor strength relation for the dislocation based formulation. Finally, the grain size-dependent constitutive model is validated by comparing the predicted stress-strain behavior of polycrystal copper samples under uniaxial loading with experimental results.

A micropolar continuum model of diffusion creep

A coupled model of diffusional creep of polycrystalline solids based on climb of dislocations at grain boundaries

Micromorphic Modelling of Grain Size Effects in Metal Polycrystals

A Discrete Dislocation Plasticity Model of Creep in Polycrystalline Thin Films

Recoverable Creep Deformation and Transient Local Stress Concentration Due to Heterogeneous Grain-Boundary Diffusion and Sliding in Polycrystalline Solids

Continuum modeling of mechanically-induced creep in dense granular materials

An Investigation of the Deformation Mechanism in Grain Size-Sensitive Newtonian Creep

An Atomistic Study of Diffusion-Mediated Plasticity and Creep using Phase Field Crystal Methods

Anisotropic rheology during grain boundary diffusion creep and its relation to grain rotation, grain boundary sliding and superplasticity

Generalised Continuum Modelling of Grain Size Effects in Polycrystals

Field Theory and Diffusion Creep Predictions in Polycrystalline Aggregates

A continuum theory for dynamic recrystallization with microstructure-related length scales

A multi-physics model for the evolution of grain microstructure

A continuum model for granular materials exhibiting a smooth transition between inelastic flow and elastic jamming

A thermodynamics-based micro-macro elastoplastic micropolar continuum model for granular materials

Grain size-dependent crystal plasticity constitutive model for polycrystal materials

Atomistic and Continuum Studies of Diffusional Creep and Associated Dislocation Mechanisms in Thin Films on Substrates

A Crystal Plasticity-Based Creep Model Considering the Concurrent Evolution of Point Defect, Dislocation, Grain Boundary, and Void

A Nucleation Rate Limited Model for Grain Boundary Creep

Polycrystal plasticity with grain boundary evolution: A numerically efficient dislocation-based diffuse-interface model

Strain localisation during diffusion creep: influence of grain coarsening and grain boundary sliding