Abstract:The ability to undercool and solidification mechanism of liquid quinary Ni40Zr28.5Ti16.5Al10Cu5 alloy are investigated by electromagnetic levitation (EML) and drop tube (DT) technique. Under the EML condition, the maximum undercooling of levitated alloy can reach up to 290 K (0.21TL). Under the DT condition, the alloy achieves higher undercooling than EML, and solidifies finally into metallic glass. At lower undercooling, the solidification structure of the alloy is composed of primary Ni3Ti phase, secondary Ni10Zr7 phase and eutectic (Ni10Zr7+Ni21Zr8) phase. With the rise of undercooling, the solidification structure displays the following evolution events: phase morphology refinement, primary phase inhibition, phase number reduction, and amorphous phase formation. By using the high-speed cinematography technique, three nucleation modes are distinctly observed on the levitated alloy melt surface at the beginning of solidification, that is, single-point nucleation, multi-point nucleation and annular nucleation. The levitation state corresponding to single-point mode nucleation is relatively stable, and the alloy undercooling is also relatively low. The annular nucleation only occursin the case with high rotation speed, and the undercooling is greater than 208 K. The discrepancy between nucleation modes is due to the He gas flow for forced cooling. The theoretical calculations indicate that the alloy droplets achieve high undercoolingand large cooling rate under the DT condition. The experimental results show that when the droplet diameter decreases to 498 μm, the amorphous phase begins to appear in the alloy particles. It is noteworthy that the amorphous phase is preferentially formed inside the droplet, but not on the outer surface. The morphology of solidification structure reveals that different regions of the droplet have various local undercoolings, which result in the distribution characteristics of amorphous phase. The volume fraction of amorphous phase increases linearly with the decrease of particle diameter. When the droplet diameter decreases to 275 μm, the alloy droplets are completely frozen into glassy particles. The average eutecticspacing values are also measured at different alloy undercoolings. Compared with the classical binary eutectic growth model, the experimental eutectic growth law exhibits a large deviation in index. This indicates that the eutectic growth in multicomponent alloys displays more complex kinetic characteristics.

Forming mechanism of the precursor film in high temperature molten metal system: insight of structural disjoining pressure

Formation Mechanism of Precursor Films at High Temperatures: A Review

Microscopic Structure Evolution and Amorphous Solidification Mechanism of Liquid Quinary Zr<sub>57</sub>Cu<sub>20</sub>Al<sub>10</sub>Ni<sub>8</sub>Ti<sub>5</sub> Alloy

Characteristics of Precursor Film in the Wetting of Zr-based Alloys on ZrC Substrate at 1253 K

Rapid Solidification Mechanism of Liquid Quinary Ni-Zr-Ti-Al- Cu Alloy Investigated by High-Speed Cinematography

Microstructural pattern formation during liquid metal dealloying: Phase-field simulations and theoretical analyses

Wetting Kinetics and Spreading Phenomena of the Precursor Film and Bulk Liquid in the AgCuTi/TC4 System

Microstructure development and morphological transition during deposition of immiscible alloy films

On the Melt Pool Flow and Interface Shape of Dissimilar Alloys Via Selective Laser Melting

Self-organized Composite Morphologies and Interface Instability of Immiscible Alloy Thin Films During Physical Vapor Deposition: Insights from Phase-Field Simulations

Interdiffusion cross-high-entropy alloys, nano-multilayer foils, and Al interface: An atomistic simulation

Effect of Substrate Chemistry on Prenucleation

Formation Mechanism for the Nanoscale Amorphous Interface in Pulse-Welded Al/Fe Bimetallic Systems

Formation mechanism and microstructure characterization of nickel-aluminum intertwining interface in cold spray

Evolution and formation of dissimilar metal interfaces in fusion welding

The mechanism of morphogenesis in a phase-separating concentrated multicomponent alloy

First-principles Investigation of the Effect of Interfacial Compositions on the Formation Energies of Ω′ and T1 Structures

Formation of Naturally Deposited Film and Its Effect on Interfacial Heat Transfer During Strip Casting of Martensitic Steel

On Melt Concentration at the Solid/liquid Interface During Preparation of Directionally Solidified Sn–36 At.%ni Peritectic Alloy

Interfacial structure evolution of the growing composite precipitates in Al-Cu-Li alloys