Characterization of Contact Pressure Distribution and Bruising Prediction of Apple under Compression Loading

Jiaping Wang,Chao Wang,Jie Wu

DOI: https://doi.org/10.3390/pr12030543

IF: 3.5

2024-03-11

Processes

Abstract:The pressure distribution characteristics of an apple subjected to compressive loading were investigated using the pressure-sensitive film (PSF) technique combined with apple bruise measurements. Pressure was unevenly distributed in the elliptical contact region. The average pressure had no effect on bruising because it changed slightly in the range of 0.26–0.31 MPa with increasing load. Pressures of 0.20–0.40 MPa accounted for 72% of the total pressure area. Comparatively, the area where pressure over 0.50 MPa was distributed could be ignored and showed little contribution to the bruise area. The contact edge subjected to pressure below 0.10 MPa showed that no bruising occurred. As a result, the relationship between the ≥0.10 MPa pressure area strongly correlated with the bruise area according to a linear equation, with a correlation coefficient of ≥0.99. When this relationship was applied to determine the bruise area with FE, satisfactory predicted results were obtained with minor error rates of 0–7.89% for loads of 54–80 N. But larger prediction errors occurred when the load was above 90 N, suggesting that the linear elastic FE model may not be appropriate for accurately predicting apple bruising.

engineering, chemical

What problem does this paper attempt to address?

The paper attempts to address the issue of contact pressure distribution and damage prediction of apples under compressive loads. Specifically, the study aims to measure the contact area and pressure of apples during compression tests using Pressure Sensitive Film (PSF) technology and to determine the relationship between these contact pressure areas and the damage areas of the apples. Ultimately, the research results will be used to validate the output of Finite Element (FE) models to improve the accuracy of predicting apple damage areas. This will help in designing apple harvesting and packaging machinery to reduce the likelihood of apple damage.

The main content of the paper is as follows:

1. **Research Background**:
- Apples may be subjected to different types of loads during packaging, sorting, storage, and transportation, leading to mechanical damage.
- Static loads are one of the main causes of apple damage, with waste due to static loads potentially reaching over 30% annually.
- The focus of the research is on the damage caused by static loads on apples.

2. **Research Methods**:
- Using Pressure Sensitive Film (PSF) technology combined with apple damage measurement to study the contact pressure distribution of apples under compressive loads.
- Measuring the contact pressure and damage under different loads (50, 52, 54, 56, 58, 60, 70, 80, 90, and 100 N) through compression tests.
- Using Finite Element Analysis (FE) to simulate actual compression tests and verify the accuracy of the model's predictions.

3. **Research Results**:
- Contact pressure is unevenly distributed within the elliptical contact area.
- The average pressure varies slightly within the range of 0.26–0.31 MPa, with no significant impact on damage.
- The area with pressure in the range of 0.20–0.40 MPa accounts for 72% of the total pressure area, while the area with pressure exceeding 0.50 MPa contributes less to damage.
- No damage was observed at the contact edges with pressure below 0.10 MPa.
- There is a strong linear correlation between the pressure area of ≥0.10 MPa and the damage area, with a correlation coefficient of ≥0.99.
- Under loads of 54–80 N, the error rate of predicting damage area using the FE model is 0–7.89%, but the prediction error is larger under loads above 90 N, indicating that the linear elastic FE model may not be suitable for accurately predicting apple damage under high loads.

4. **Conclusion**:
- There is a strong correlation between the contact pressure areas measured by PSF technology and the damage areas of apples.
- Finite Element Analysis can be combined with data from PSF technology to improve the accuracy of predicting apple damage areas.
- These results will help in designing more effective apple harvesting and packaging machinery to reduce damage during handling.