Abstract:Vanadium redox flow battery (VRFB) is an amateur technology that passed pilot stages in fulfilling the stationary applications at the energy storage market with a high share of renewable power generation. The commercial applications of VRFBs require the optimization of their internal losses and developing the optimal control strategies for in-grid operation. This calls for a deep understanding of the internal VRFB processes, which greatly benefit from both the mathematical modeling and experimental testing for the model validation and refinement. However, the available experimental data for VRFBs is usually limited by open-circuit voltage (OCV) and potential (OCP), charge/discharge voltage profiles at constant load current, full cell polarization curves at the fixed state of charge (SOC), and internal stack ohmic resistances. This also complicates the decoupling and accessing the voltage loss sources, with the prevailing ones usually classified as ohmic, concentration, and activation overpotentials. As such, Aaron et al. (1) showed that decoupling of overpotentials at positive and negative half-cell requires the half-cell potentials measurements with reference electrodes (RE) in addition to full cell data. Different configurations of RE incorporation (2–4) were suggested with a limited agreement with full cell experimental data. The alternative approach with extrapolation of parameters presented in the literature is also challenging due to their strong dependence on an experimental protocol (e.g., the electrode material and its pre-treatment procedure, a membrane, and a setup geometry). As an illustration, the comprehensive review Roznyatsovskaya et al. (5) highlights the four orders of magnitude difference in reported surface area-normalized rate constants. Therefore, the development of a self-consistent experimental setup is crucial for understanding and decoupling internal losses for flow batteries. Combined with VRFB modeling, this may extend accurate predictions of its operation at extreme SOCs and load currents, where voltage losses hamper the efficiency of the battery with the dominating ones usually attributed to concentration (mass-transport in solutions) and activation (sluggish kinetics of reactions on electrodes) overpotentials. Herein, we developed the experimental setup adopting a 5cm 2 single flow cell equipped with reference electrodes at positive and negative sides. The experiments were performed in symmetric and full cell designs. The polarization curves were measured at different SOCs [10 – 90 %], electrolyte flow rates [5-30 ml min -1 ], and load currents. The additional effort was made to compare the results of the experiments in symmetric and full cell designs and extract the apparent kinetic rate constants for positive and negative half-cells. The latter was performed within the 0D modeling approach, which is based on general mass and charge conservation principles. The key feature of the model is the approach for the determination of the integral mass-transfer coefficient on the electrode-electrolyte interface that allows describing non-linear polarization behaviour at high current densities. The effective thermodynamically consistent single-step reaction mechanisms were considered at both half cells, thus decreasing the number of free kinetic parameters. Overall, the proposed approach demonstrated the growing impact of the membrane losses at high current densities. The extracted apparent rate constants under conditions of a real flow battery provide important insights for developing reliable and efficient VRFBs applicable for energy storage systems. 1 D. Aaron, Z. Tang, A. B. Papandrew and T. A. Zawodzinski, J. Appl. Electrochem., 2011, 41, 1175–1182. 2 H. Lim, J. S. Yi and D. Lee, J. Power Sources, 2019, 422, 65–72. 3 S. Ressel, A. Laube, S. Fischer, A. Chica, T. Flower and T. Struckmann, J. Power Sources, 2017, 355, 199–205. 4 M. Cecchetti, A. Casalegno and M. Zago, J. Power Sources, 2018, 400, 218–224. 5 N. Roznyatovskaya, J. Noack, K. Pinkwart and J. Tübke, Curr. Opin. Electrochem., 2020, 19, 42–48.

Characteristics of a Nickel Vanadium redox flow battery Based on COMSOL

Performance Improvement of a Hydrogen-Bromine Flow Battery

Characteristics of a Titanium Manganese redox flow battery based on Comsol

An Advanced Composite Membrane for the All-Vanadium Redox Flow Battery

Computational Modeling of a 2D Vanadium Redox Flow Battery Cell

Identification of Overpotentials in Vanadium Redox Flow Battery with Reference Electrodes and Determination of Apparent Electrochemical Rate Constants

Performance of a vanadium redox flow battery with a VANADion membrane

Numerical Parametric Investigation of Nonaqueous Vanadium Redox Flow Batteries

Hydrodynamic and Electrochemical Analysis of Compression and Flow Field Designs in Vanadium Redox Flow Batteries

Molecular Dynamics Simulation of the Electrochemical Cell Design for All- vanadium Redox Flow Battery

Overview of the factors affecting the performance of vanadium redox flow batteries

Modeling of Vanadium Redox Flow Battery and Electrode Optimization with Different Flow Fields

Dynamic modeling of long-term operations of vanadium/air redox flow battery with different membranes

Performance evaluation of redox flow batteries using major parameters summarizing effects of structure and operation conditions

The numerical study of vanadium redox flow battery performance with different electrode morphologies and electrolyte inflow patterns

Inter-compartment concentration monitoring of key species in a vanadium redox flow cell operating with and without polarization: Experiments and construction of a predictive model

Asymmetric Structure Design of a Vanadium Redox Flow Battery for Improved Battery Performance

Numerical Simulation of Flow Field Structure of Vanadium Redox Flow Battery and its Optimization on Mass Transfer Performance

Structural Modification of Vanadium Redox Flow Battery with High Electrochemical Corrosion Resistance

Evaluating the Stability and Performance of Nasicon in Low-Cost High Charge Density Redox Flow Battery Electrolytes

Performance Improvement of a Vanadium Redox Flow Battery with Asymmetric Electrode Designs