Abstract:Objectives: During the manufacturing of Porcelain Veneered Zirconia (PVZ) dental crowns, the veneer-core system undergoes high-temperature firing cycles and gets fused together which is then, under a controlled setting, cooled down to room temperature. During this cooling process, the mismatch in thermal properties between zirconia and porcelain leads to the development of transient and residual thermal stresses within the crown. These thermal stresses are inherent to the PVZ dental crown systems and render the crown structure weak, acting as a precursor to veneer chipping, fracture, and delamination. In this study, the introduction of an intermediate functionally graded material (FGM) layer at the bi-material interface is investigated as a potentially viable alternative for providing a smoother transition of properties between zirconia and porcelain in a PVZ crown system. Methods: Anatomically correct 3D crown models were developed for this study, with and without the FGM layer modeled at the bi-material interface. A viscoelastic finite element model was developed and validated for an anatomically correct bilayer PVZ crown system which was then used for predicting residual and transient stresses in the bilayer PVZ crown. Subsequently, the viscoelastic finite element model was further extended for the analysis of graded sublayers within the FGM layer, and this extended model was used for predicting the residual and transient stresses in the functionally graded PVZ crown, with an FGM layer at the bi-material interface. Results: The study showed that the introduction of an FGM layer at the bi-material interface has the potential to reduce the effects from transient and residual stresses within the PVZ crown system relative to a bilayer PVZ crown structure. Furthermore, the study revealed that the FGM layer causes stress redistribution to alleviate the stress concentration at the interfacial surface between porcelain and zirconia which can potentially enhance the durability of the PVZ crowns towards interfacial debonding or fracture. Significance: Thus, the use of an FGM layer at the bi-material interface shows a good prospect for enhancing the longevity of the PVZ dental crown restorations by alleviating the abrupt thermal property difference and relaxing thermal stresses.

Metabolism of apical versus basolateral sn-2-monoacylglycerol and fatty acids in rodent small intestine** This work was supported by National Institutes of Health Grant DK-38389 and the Busch Biomedical Research Fund. Published, JLR Papers in Press, April 17, 2008.

Wegener Granulomatose und mikroskopische Polyangiitis: Diagnostische und klinische Ergebnisse bei 54 Patienten im Langzeitverlauf

The effect of graded glass-zirconia structure on the bond between core and veneer in layered zirconia restorations

Investigation of the structure and mechanical properties of a novel dental graded glass/zirconia ceramic

Construction of Nanostructured Glass-Zirconia to Improve the Interface Stability of Dental Bilayer Zirconia

‘Felson Signs’ revisited

Zirconia toughened fluorosilicate glass-ceramics for dental prosthetic restorations

Effect of Air-Abraded Versus Laser-Fused Fluorapatite Glass-Ceramics on Shear Bond Strength of Repair Materials to Zirconia

Functionally graded bi-material interface for Porcelain Veneered Zirconia dental crowns: A study using viscoelastic finite element analysis

1.14 b/s/Hz spectrally efficient 50/spl times/85.4-Gb/s transmission over 300 km using copolarized RZ-DQPSK signals

Fracture and Interfacial Delamination Origins of Bilayer Ceramic Composites for Dental Restorations

A new surface treatment method: fusing glass ceramic to zirconia

Infiltration OF 5Y-PSZ with thermally compatible glass: Strength, microstructure and failure mode analyses

Fracture behaviour of zirconia ceramic cantilever fixed dental prostheses in vitro

Bioinspired silica-infiltrated zirconia bilayers: Strength and interfacial bonding

Effects of glass-ceramic spray deposition manipulation on the surface characteristics of zirconia dental restorations

Effect of preparation design and endodontic access on fracture resistance of zirconia overlays in mandibular molars: An in vitro study

Sliding contact wear and subsurface damage of CAD/CAM materials against zirconia

Fractography of Self-Glazed Zirconia with Improved Reliability

Fracture resistance and fractographic analysis of pressable glass-ceramics with different partial coverage designs for maxillary premolars

Effect of Grinding and Regenerative Heat Treatment on the Fracture Resistance of a Zirconia/Porcelain Veneer Interface