Abstract:Abstract Rock mass characterization is a very important part of engineering geological investigation. For a better understanding of the rock mass behaviour, it is crucially important to obtain as much as possible information about the discontinuity network, especially about orientation and the number of dominant discontinuity sets. The traditional methodology includes field mapping which dominantly produces a limited amount of data and consequently only a rough estimate about discontinuity network. To increase the number of measurements and to eliminate orientation bias, rock mass on the Špičunak rock slope in Gorski kotar, Croatia, was analysed using a combination of 3D Point Cloud and Textured Mesh Model generated from 3D Point Cloud by Poisson surface reconstruction. Both models were obtained from Terrestrial Laser Scanning. Two considerably different parts of a rock slope, with different weathering conditions and different degrees of fracturing were mapped. Discontinuities were mapped in the field and on the models using manual mapping techniques and semi-automated methods. Manual mapping on a 3D Point Cloud and Textured Mesh Model was done by Compass plugin and by Trace a polyline tool in Cloud Compare software version V2.12 and semi-automated mapping methods were done by Discontinuity Set Extractor and qFacet Fast Marching plugin for Cloud Compare software version V2.12. This study was used to show how the application of different methodologies, for the detection of geometric properties of discontinuities, influences the result. Statistical analyses were performed on the collected data to determine differences in the accuracy between the mapping techniques. Manual mapping on the 3D Point Cloud and high-resolution Textured Mesh Model showed good agreement with field measurements, apart from the higher number of discontinuities mapped by remote sensing methods. On the other hand, significant deviations were found between manual and semi-automated mapping techniques. Semiautomated methods did not correctly detect certain discontinuities, especially bedding planes that are perpendicular to a rock face. Also, semi-automated methods overestimate the number of discontinuity sets, especially in a highly weathered and highly fractured rock mass. These differences between methods can influence kinematic analysis results. Based on the results, an appropriate methodology was proposed to utilize the advantages of both manual and semiautomated methods. The proposed approach presents a powerful tool to accurately map and measure discontinuity orientation with results comparable to the field measurements.

Enhanced discontinuity mapping of rock slopes exhibiting distinct structural frameworks using digital photogrammetry and UAV imagery

Rapid Seismic Risk Assessment of Bridges Using UAV Aerial Photogrammetry

Development and application of UAV-SfM photogrammetry for quantitative characterization of rock mass discontinuities

3D Reconstruction of Coastal Cliffs from Fixed-Wing and Multi-Rotor UAS: Impact of SfM-MVS Processing Parameters, Image Redundancy and Acquisition Geometry

Mapping landslide displacements using Structure from Motion (SfM) and image correlation of multi-temporal UAV photography

Research on fine collection and interpretation methods of discontinuities on high-steep rock slopes based on UAV multi-angle nap-of-the-object photogrammetry

Author Response for "semi‐automatic Identification of Discontinuity Parameters in Rock Masses Based on Unmanned Aerial Vehicle Photography"

Identification of potential rockfall sources using UAV-derived point cloud

Application of UAV Digital Photogrammetry in Geological Investigation and Stability Evaluation of High-Steep Mine Rock Slope

Assessment of UAV and Ground-Based Structure from Motion with Multi-View Stereo Photogrammetry in a Gullied Savanna Catchment

Digital Outcrop Model Generation from Hybrid UAV and Panoramic Imaging Systems

A timely method for post-disaster assessment and coastal landscape survey using drone and satellite imagery

Fine-Resolution Repeat Topographic Surveying of Dryland Landscapes Using UAS-Based Structure-from-Motion Photogrammetry: Assessing Accuracy and Precision against Traditional Ground-Based Erosion Measurements

Enhancing UAV-SfM 3D Model Accuracy in High-Relief Landscapes by Incorporating Oblique Images

3D Rock Structure Digital Characterization Using Airborne LiDAR and Unmanned Aerial Vehicle Techniques for Stability Analysis of a Blocky Rock Mass Slope

Integration of Terrestrial and Drone-Borne Hyperspectral and Photogrammetric Sensing Methods for Exploration Mapping and Mining Monitoring

Mapping erosion and deposition in an agricultural landscape: Optimization of UAV image acquisition schemes for SfM-MVS

Semi‐automatic identification of discontinuity parameters in rock masses based on Unmanned Aerial Vehicle photography

A Machine Learning Approach to Extract Rock Mass Discontinuity Orientation and Spacing, from Laser Scanner Point Clouds

UAV-based doline mapping in Brazilian karst: A cave heritage protection reconnaissance

Detection of geometric properties of discontinuities on the Špičunak rock slope (Croatia) using high-resolution 3D Point Cloud generated from Terrestrial Laser Scanning