Abstract:The broad technological concept as so-called "hybrid additive manufacturing" is introduced into the fabrication of flexible strain sensing structure, employing the combination process of fused deposition modeling (FDM) 3D printing technique and ultrasonic cavitation-enabled treatment. We customize the FDM settings to print auxetic structures with a negative Poisson's ratio (NPR), using the flexible thermoplastic polyurethane (TPU) material. Then, we employ the ultrasonic cavitation-enabled treatment conducted towards the flexible auxetic structure immersing in carbon nanotubes (CNTs) liquid, aiming to embed the CNTs into the surface layer of the auxetic structures. It is equivalent to two additive manufacturing steps, proving effective in designing and fabricating flexible strain sensors. Instead of 3D printing after the hybridization of the TPU matrix material, this manufacturing procedure can ensure that the intrinsic excellent mechanical properties of TPU are not weakened due to the internally mixed conductive materials but able to exhibit usable sensing performances. The Poisson's ratio of the sensor structure is -0.8. The sensor achieves over 300% strain. The sensitivity within the initial strain range is 2.661. The reliability of signal acquisition during the cyclic deformations is proved. Its response-recovery duration under 5% strain at 500 mm/min deformation rate is 130 ms(response)-250 ms(recovery). It gives accurate feedback to external stimuli at different frequencies. It can maintain stable output signals during 3000 cycles of stretching. It also can sense 1% minor-strain stimuli. The strain sensing behavior of the fabricated flexible sensor with the auxetic structure is detailed. The CNTs are combined tightly with the TPU surface layer to form a conductive network with variable resistance during recoverable deformation of the auxetic structure. The macro and micro-mechanisms of sensing are dissected, considering the tunneling effect of discontinuous CNTs. The hybrid additive manufacturing process is verified to be feasible, credible, and low-cost for easy fabrication of flexible strain sensors with complex geometry configurations.

Additive Manufacturing of Stretchable Polyurethane/Graphene/Multiwalled Carbon Nanotube-Based Conducting Polymers for Strain Sensing

Additive Manufacturing of Stretchable Multi-Walled Carbon Nanotubes/Thermoplastic Polyurethanes Conducting Polymers for Strain Sensing

A Flexible Strain Sensor of Porous Conductive Silicone Rubber Composites Prepared from High Internal Phase Emulsion

Enhanced performance of 3D printed highly elastic strain sensors of carbon nanotube/thermoplastic polyurethane nanocomposites via non-covalent interactions

Multi-Walled Carbon Nanotube-Enhanced Polyurethane Composite Materials and the Application in High-Performance 3D Printed Flexible Strain Sensors

Wearable Strain Sensors Based on a Porous Polydimethylsiloxane Hybrid with Carbon Nanotubes and Graphene

Highly sensitive and stretchable CB/GNPs-TPU strain sensor with porous microstructure for multifunctional strain sensing

Strain Sensing Behavior of Conductive Polymer/Carbon Nanotube Composites Coated Fiber

Highly Stretchable, Anti-Corrosive and Wearable Strain Sensors Based on the PDMS/CNTs Decorated Elastomer Nanofiber Composite

Flexible and Transparent Strain Sensors with Embedded Multiwalled Carbon Nanotubes Meshes.

TPU/CNTs Flexible Strain Sensor with Auxetic Structure Via a Novel Hybrid Manufacturing Process of Fused Deposition Modeling 3D Printing and Ultrasonic Cavitation-Enabled Treatment

Facile Fabrication and Performance of Robust Polymer/carbon Nanotube Coated Spandex Fibers for Strain Sensing

Highly Stretchable Strain Sensor Based on Polyurethane Substrate Using Hydrogen Bond-Assisted Laminated Structure for Monitoring of Tiny Human Motions

Fabrication of electrically conductive poly(styrene-b-ethylene-ran-butylene-b-styrene)/multi-walled carbon nanotubes composite fiber and its application in ultra-stretchable strain sensor

Flexible Strain Sensors with Enhanced Sensing Performance Prepared from Biaxially Stretched Carbon Nanotube/Thermoplastic Polyurethane Nanocomposites

3D printed high-performance flexible strain sensors based on carbon nanotube and graphene nanoplatelet filled polymer composites

3D Printing of Highly Stretchable Strain Sensors Based on Carbon Nanotube Nanocomposites

A Multi-Functional Wearable Sensor Based on Carbon Nanomaterials Reinforced TPU Fiber with High Sensitivity

Facile fabrication and performance of robust polymer / carbon nanotube coated spandex fi bers for strain sensing

A Multifunctional Flexible Strain Sensor Based on an Excellent Sensing Performance PDMS-MXene@CNT/TPU Nanofiber Membrane with Hydrophobic and Photothermal Conversion Performance

Stretchable strain sensors based on conductive coating cracks with improved interfacial adhesion by wet phase separation treatment