Enabling Dynamic Security Policy in the Java Security Manager

F. Autrel,N. Cuppens-Boulahia,F. Cuppens

DOI: https://doi.org/10.1007/978-3-642-37119-6_12

2012-10-25

Abstract:

What problem does this paper attempt to address?

An Energy Efficient Process for Degrading Perfluorooctanoic Acid (PFOA) Using Strip Fountain Dielectric Barrier Discharge Plasma

Jiushan Cheng,Yangyang Fan,Xueyun Pei,Di Tian,Zhongwei Liu,Lizhen Yang,Eric Feng,Hai-Feng Ji,Qiang Chen

DOI: https://doi.org/10.3390/w14152420

IF: 3.53

2022-01-01

Water

Abstract:Perfluorooctanoic acid (PFOA) is an artificially synthesized per-fluorinated chemical widely used in industry. It is often released into the environment without treatment and causes pollution in groundwater. In this paper, we employed a strip fountain dielectric barrier discharge (SF-DBD) plasma source to degrade PFOA from the water. The effects of power supply mode, discharge gases, pH, the conductivity of the solution, concentration, etc., on the degradation efficiency were studied. For a 200 mL sample of 75 mg/L PFOA, a 99% degradation efficiency with a 204.5 μg/kJ energy production rate was achieved using an average power of 43 W negative pulse argon plasma for 50 min at atmospheric pressure. The total organic carbon concentration (TOC) decreased by 63% after a 60 min treatment. The SF-DBD proves to be a promising and energy-saving technique to efficiently remove PFOA from water.
Degradation of Nitenpyram Pesticide in Aqueous Solution by Low-Temperature Plasma

S. P. Li,Y. Y. Jiang,X. H. Cao,Y. W. Dong,M. Dong,J. Xu

DOI: https://doi.org/10.1080/09593330.2013.765914

IF: 3.475

2013-01-01

Environmental Technology

Abstract:In order to study the new technique of plasma wastewater treatment, the degradation behaviour ofnitenpyram (NTP) pesticide was investigated in a low-temperature plasma formed during a dielectric barrier discharge process. The reactor was a radial flow sedimentation tank centred around the water inlet. We studied the effect of pesticide concentration and input power of the dielectric barrier discharge, together with the effect of external factors on the degradation of nitenpyram pesticide wastewater such as conductivity and the use of various of catalysts, and the reaction products were analyzed by high-performance liquid chromatography mass spectrometry (HPLC-MS). The results showed that NTP could be effectively removed from aqueous solution by low-temperature plasma. Increasing the input power could improve the efficiency of degradation, conforming to a first-order kinetic model. Use of a suitable catalyst clearly improved the degradation process, as also did low conductivity. The pH of NTP was reduced with discharge time.
Degradation of Methylene Blue by Dielectric Barrier Discharge Plasma Coupled with Activated Carbon Supported on Polyurethane Foam

Lihang Wu,Qinglong Xie,Yondbo Lv,Zhiyong Zhang,Zhenyu Wu,Xiaojiang Liang,Meizhen Lu,Yong Nie

DOI: https://doi.org/10.1039/c9ra05238k

IF: 4.036

2019-01-01

RSC Advances

Abstract:The degradation of methylene blue (MB) using a novel dielectric barrier discharge plasma reactor coupled with activated carbon supported polyurethane foam (AC/PUF) was investigated in this paper. The plasma reactor combining a glass bead-packed bed and a microporous plate was developed. The AC/PUF provided sufficient contact area between carbon media and pollutants and hence revealed a good MB removal capacity. The effects of input voltage and initial MB solution concentration on MB degradation efficiency were examined. Kinetic study indicated that plasma and AC/PUF in the coupled system had a good synergistic effect in MB degradation. The degradation efficiency of 100 ppm MB solution could reach 97.9% with 10 min treatment in the coupled system, which was close to that obtained by plasma treatment alone for 30 min (97.5%). The COD removal in the plasma and AC/PUF coupled system (90.7%) was much higher than that obtained by plasma treatment followed by AC/PUF adsorption (58.3%). In addition, the energy yield (G(50)) of the coupled system was up to 38.3 g kW(-1) h(-1), suggesting great energy efficiency of the system. Moreover, repeated use experiments of AC/PUF showed the good utilization potential of the coupled system. Finally, a possible degradation pathway of MB was proposed.
Effect of dielectric barrier discharge plasma on persulfate activation for rapid degradation of atrazine: Optimization, mechanism and energy consumption

Tianyao Shen,Xiaojing Wang,Peng Xu,Chunyan Yang,Jiaqin Li,Peng Wang,Guangshan Zhang

DOI: https://doi.org/10.1016/j.envres.2022.113287

IF: 8.3

2022-04-01

Environmental Research

Abstract:Dielectric barrier discharge plasma (DBDP) is an emerging and promising advanced oxidation process (AOP) for wastewater treatment. After investigating the effect of input voltage, O3 (generated by dielectric barrier discharge), and peroxydisulfate (PDS) dosage, the DBDPO3/PDS system was established. With the assistance of PDS, the atrazine (ATZ) removal efficiency increased from 69.67% to 82.46% within 25 min. Synergistic effect calculation suggests that there were markedly synergies between DBDP, O3, and PDS. Under the effect of SO4-•, the total organic carbon (TOC) removal and dechlorination efficiency were significantly improved. In addition, the DBDPO3/PDS system maintained the ATZ removal efficiency at a high level over a wide range of initial pH values. According to quenching experiments and electron paramagnetic resonance (EPR) detection, the dominant radical for ATZ degradation in the DBDPO3/PDS system was HO•. A possible degradation pathway of ATZ was proposed based on density functional theory (DFT) analysis, quadrupole-time of flight-liquid chromatography/mass spectrometry (Q-TOF-LC/MS) results, and related literature. The acute toxicity to aquatic minnows and the developmental toxicity of intermediate products prediction confirmed that the DBDPO3/PDS system could effectively reduce ATZ toxicity. The electrical energy per order (EEO) was 7.10 kWh m-3 order-1 illustrating that the DBDPO3/PDS was a more energy-economic system than other energy-intensive processing technologies.

environmental sciences,public, environmental & occupational health
Removal of disinfection byproducts through integrated adsorption and reductive degradation in a membrane-less electrochemical system

Kaichao Yang,Ibrahim M Abu-Reesh,Zhen He

DOI: https://doi.org/10.1016/j.watres.2023.120519

2023-10-01

Abstract:Proper control/removal of disinfection byproducts (DBPs) is important to drinking water safety and human health. In this study, a membrane-less electrochemical system was developed and investigated to remove DPBs through integrated adsorption and reduction by granular activated carbon (GAC)-based cathode. Representative DPBs including trihalomethanes and haloacetonitriles at drinking water concentrations were used for removal experiments. The proposed system achieved >70% removal of most DBPs in a batch mode. The comparison with control tests under either open circuit or hydrolysis demonstrated the advantages of electrochemical treatment, which not only realized higher DPBs removal but also extended GAC cathode lifetime. Such advantages were further demonstrated with continuous treatment. High dechlorination and debromination efficiencies were obtained in both batch (82.2 and 94.3%) and continuous (79.3 and 87.6%) reactors. DBPs removal was mainly contributed by the electrochemical reduction and adsorption by the GAC-based cathode, while anode showed little oxidizing effect on DBPs and halide ions. Dehalogenated products of chloroform and dichloroacetonitrile were identified with toxicity reduction. The energy consumption of the continuously operated system was estimated to be 0.28 to 0.16 kWh m-3. The proposed system has potential applications for wastewater reuse or further purification of drinking water.
Plasma-microbubble treatment and sustainable agriculture application of diclofenac-contaminated wastewater

Qi Liu,Wenchong Ouyang,Xusheng Yang,Yuanyuan He,Zhengwei Wu,Kostya (Ken) Ostrikov

DOI: https://doi.org/10.1016/j.chemosphere.2023.138998

IF: 8.8

2023-05-22

Chemosphere

Abstract:The demand for efficient wastewater treatment is becoming increasingly urgent due to the rising threat of pharmaceutical residues in water. As a sustainable advanced oxidation process, cold plasma technology is a promising approach for water treatment. However, the adoption of the technology encounters several challenges, including the low treatment efficiency and the potentially unknown environmental impact. Here, microbubble generation was integrated with cold plasma system to enhance treatment of wastewater contaminated with diclofenac (DCF). The degradation efficiency depended on the discharge voltage, gas flow, initial concentration, and pH value. The best degradation efficiency was 90.9% after 45 min plasma-bubble treatment under the optimum process parameters. The hybrid plasma-bubble system exhibited strongly synergistic performance heralded by up to seven-times higher DCF removal rates than the two systems operated separately. The plasma-bubble treatment remains effective even after addition of SO 4 2− , Cl − , CO 3 2− , HCO 3 − , and humic acid (HA) as interfering background substances. The contributions of •O 2 − , O 3 , • OH, and H 2 O 2 reactive species to the DCF degradation process were specified. The synergistic mechanisms for DCF degradation were deduced through the analysis of the degradation intermediates. Further, the plasma-bubble treated water was proven safe and effective to stimulate seed germination and plant growth for sustainable agriculture applications. Overall, these findings provide new insights and a feasible approach with a highly synergistic removal effect for the plasma-enhanced microbubble wastewater treatment, without generating secondary contaminants.

environmental sciences
A Biphasic Plasma Microreactor for Pollutants Degradation in Water

Ghewa Akiki,Stephanie Ognier,Pascal Rajagopalan,Cecilia Devaux,Ichiro Kano,Noelia Merino,Simeon Cavadias,Yann Ratieuville,Xavier Duten,Michael Tatoulian

DOI: https://doi.org/10.1007/s11090-024-10503-6

2024-09-11

Plasma Chemistry and Plasma Processing

Abstract:The combination of plasma technology with microfluidics has gained significant attention in recent years. The unique characteristics of microfluidic chips, such as high surface-to-volume ratio and efficient mass transfer, coupled with plasma's ability to provide the necessary green energy for the degradation of complex molecules, make this combination promising for water and wastewater treatment applications. A gas/liquid biphasic dielectric barrier discharge (DBD) plasma microreactor powered by a nano-pulsed excitation source, at atmospheric pressure, was used to study the degradation of p-benzoquinone and caffeine in water, chosen as model molecules for water pollution. Based on High Performance Liquid Chromatography (HPLC) analyses, the argon plasma was able to completely degrade both molecules at concentrations 10 − 5 , 10 − 4 and 10 − 3 mol/L. At higher concentration (10 − 2 mol/L), the plasma promotes the synthesis of hydroquinone from p-benzoquinone. A 50% mineralization is achieved after plasma for the caffeine in aqueous solution at 10 − 5 M.

engineering, chemical,physics, fluids & plasmas, applied
Removal of persistent organic contaminants from wastewater using a hybrid electrochemical-granular activated carbon (GAC) system

Giannis-Florjan Norra,Jelena Radjenovic

DOI: https://doi.org/10.1016/j.jhazmat.2021.125557

IF: 13.6

2021-08-01

Journal of Hazardous Materials

Abstract:A three-dimensional (3D) electrochemical flow-through reactor equipped with GAC packed bed, polarized by the electric field, was evaluated for the removal of persistent organic contaminants from real sewage effluent. The performance of the reactor was investigated for 27 consecutive runs at two anodic current densities, i.e., low current density (LCD) of 15 A m−2, and high current density (HCD) of 100 A m−2. In the HCD experiments, the adsorption ability of saturated GAC was increased, mainly due to the increase in the mesoporosity of GAC. A synergy between electrosorption/adsorption on GAC and electrooxidation was observed in terms of the removal of all target pollutants. DEET presented the highest synergy, ranging from 40% to 57%, followed by iopromide (22–46%), carbamazepine (15–34%) and diatrizoate (4–30%). The addition of GAC decreased the concentrations of toxic chlorate and perchlorate by 2-fold and 10-fold, respectively, due to their electrosorption on GAC. Also, 3D electrochemical system yielded lower concentrations of adsorbable organic iodide (AOI) and adsorbable organic chlorine (AOCl). Thus, addition of low amounts of GAC in electrochemical systems may be a low-cost and simple way of minimizing the formation and final effluent concentrations of toxic halogenated byproducts.

environmental sciences,engineering, environmental
Cold atmospheric plasma technology for removal of organic micropollutants from wastewater—a review

Amit Kumar,Nikola Škoro,Wolfgang Gernjak,Nevena Puač

DOI: https://doi.org/10.1140/epjd/s10053-021-00283-5

2021-11-01

The European Physical Journal D

Abstract:Abstract Water bodies are being contaminated daily due to industrial, agricultural and domestic effluents. In the last decades, harmful organic micropollutants (OMPs) have been detected in surface and groundwater at low concentrations due to the discharge of untreated effluent in natural water bodies. As a consequence, aquatic life and public health are endangered. Unfortunately, traditional water treatment methods are ineffective in the degradation of most OMPs. In recent years, advanced oxidation processes (AOPs) techniques have received extensive attention for the mineralization of OMPs in water in order to avoid serious environmental problems. Cold atmospheric plasma discharge-based AOPs have been proven a promising technology for the degradation of non-biodegradable organic substances like OMPs. This paper reviews a wide range of cold atmospheric plasma sources with their reactor configurations used for the degradation of OMPs (such as organic dyes, pharmaceuticals, and pesticides) in wastewater. The role of plasma and treatment parameters (e.g. input power, voltage, working gas, treatment time, OMPs concentrations, etc.) on the oxidation of various OMPs are discussed. Furthermore, the degradation kinetics, intermediates compounds formed by plasma, and the synergetic effect of plasma in combination with a catalyst are also reported in this review. GraphicAbstract
Optimization of a Low-Cost Corona Dielectric-Barrier Discharge Plasma Wastewater Treatment System through Central Composite Design/Response Surface Methodology with Mechanistic and Efficiency Analysis

Yiting Xiao,Yang Tian,Yuanhang Zhan,Jun Zhu

DOI: https://doi.org/10.3390/su16020605

IF: 3.9

2024-01-11

Sustainability

Abstract:Water pollution, which is intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and can potentially result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona dielectric-barrier discharge for wastewater treatment. Using the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) was achieved within 10 min by optimizing parameters such as pH and voltage. Furthermore, the mechanisms underlying the generation of reactive oxygen species through this device were discussed in detail and the degradation pathways of MB were elucidated. Moreover, this device is very energy-efficient, exhibiting a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m3/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

environmental sciences,environmental studies,green & sustainable science & technology
Efficient treatment of bio-contaminated wastewater using plasma technology for its reuse in sustainable agriculture

Saeed Kooshki,Pankaj Pareek,Robin Mentheour,Mário Janda,Zdenko Machala

DOI: https://doi.org/10.1016/j.eti.2023.103287

2023-07-25

Abstract:Water-related crisis represents one of the significant challenges of the rapidly growing world population. This study demonstrates an example of the novel technology of Non-Thermal Plasma (NTP) wastewater treatment for its sustainable recovery and reuse in agriculture. NTP treatment of wastewater not only causes microbial decontamination but produces Reactive Oxygen and Nitrogen Species (RONS), which can consequently improve seed germination and plant growth. We investigated the effects of the new Fountain Dielectric Barrier Discharge air plasma reactor for the treatment of bulk quantity water contaminated by Staphylococcus epidermidis or Escherichia coli bacteria. Then, employing the treated water for barley seed germination showed >20% enhancement compared to using tap water. The inactivation of bacteria in water was determined in dependence on pH, Oxidation-Reduction Potential, and correlated with chemical RONS produced in the water (hydrogen peroxide, nitrites, and especially nitrates). By utilizing the Responses Surface Methodology, we identified the optimal plasma treatment time per litre required for efficient RONS production and bactericidal effect in the wastewater treatment, which was linearly scalable with water volume. After the optimum plasma treatment time, a sharp drop in pH, and the concentrations of nitrites and hydrogen peroxide were observed, which is related to the peroxynitrite formation leading to the significant bacterial reduction up to 7-log.

environmental sciences,engineering, environmental,biotechnology & applied microbiology
Effects of sodium persulfate and persulfate on the degradation of 2,4- dichlorophenol in a dielectric barrier discharge reactor

Tingting Zhang,Kwasi Kyere-Yeboah,Yuliang Ge,Xiuchen Qiao

DOI: https://doi.org/10.1016/j.cep.2024.109953

IF: 4.264

2024-08-26

Chemical Engineering and Processing - Process Intensification

Abstract:The detection of micropollutants in surface and groundwater bodies has drawn global concern due to their environmental persistence and risk to human and aquatic life. The dielectric barrier discharge (DBD) plasma reactor was employed to degrade the micropollutant 2,4-dichlorophenol (2,4-DCP). The efficiency of the reactor was investigated, and the plasma degradation process was intensified by introducing three eco-friendly oxidants, sodium percarbonate (SPC), sodium persulfate (SPS), and hydrogen peroxide (HPO), into the reactor. Results indicated that 2,4-DCP removal increased from 62.73% to 76.37%, 81.93%, 100%, and 90.02% when 1 mM SPC, 1 mM SPS, 3 mM HPO, and 1 mM SPS + 0.33 mM SPC was added to the wastewater solution, respectively. The synergy between the oxidants and the plasma in the DBD reactor was also explored. The largest synergistic factor (1.792) was achieved when 3 mM HPO was added to the DBD reactor, followed by 0.089 for 1 mM SPC, 0.07 for 1 mM SPS, and 0.041 for 1 mM SPS+0.33 mM SPC. The main active species that catalyzed 2,4-DCP degradation were hydroxyl and sulfate radicals, and introducing the oxidants augmented their production in the solution. The synergy between the DBD+SPS+SPC led to a 58.7% total organic carbon removal. In conclusion, the 2,4-DCP degradation intermediates and mechanisms were deduced accordingly. The findings reaffirm the effectiveness of the oxidant-coupled DBD reactor in the degradation of micropollutants.

energy & fuels,engineering, chemical
Destruction of n -hexane from the air stream by pulsed discharge plasma: Modelling and key process parameters optimization by CCD-RSM

Seyed Alireza Babaee,Mohammad Sharif Hosseini,Yaghoub Hajizadeh

DOI: https://doi.org/10.1016/j.jece.2024.112922

IF: 7.7

2024-05-12

Journal of Environmental Chemical Engineering

Abstract:In this study, a Dielectric-Barrier Discharge (DBD) plasma reactor was used for the degradation of n -hexane from an air stream. a Central Composite Design (CCD) based Response Surface Methodology (RSM), (CCD-RSM) was utilized to explore the effects of experimental parameters including discharge voltage, initial concentration, gas flow rate, relative humidity and their interactions on the reactor performance. The proposed optimization model showed a satisfactory correlation between the predicted and actual results. According to the results, discharge voltage was the most significant parameter affecting the removal efficiency, CO 2 selectivity and the level of O 3 and NO x formation, whereas energy yield was mainly influenced by gas flow rate and initial concentration. At optimized conditions (discharge voltage of 8.5 kV, inlet concentration of 94.3 ppm, relative humidity of 55 % and gas flow rate of 733.16 ml/min with combined desirability of 0.921), removal efficiency of 92.57 %, CO 2 selectivity of 58.87 %, energy efficiency of 0.25 g/kWh, O 3 formation of 140.88 mg/m 3 and NO x formation of 122.46 ppm were obtained. Water vapour significantly increased the removal efficiency and CO 2 selectivity as well as reduced O 3 and NO x . The results revealed that the CCD-RSM provided the optimum process parameters for the Non-Thermal Plasma (NTP) system.

engineering, chemical, environmental
Comparative life cycle assessment of non-thermal plasma for the removal of pharmaceuticals from wastewater

E Surra,P Paíga,I Baptista,R Jorge,L Marinheiro,S Löblich,C Delerue-Matos

DOI: https://doi.org/10.1016/j.jenvman.2024.122728

2024-10-03

Abstract:Wastewater effluents are a continuous source of pharmaceuticals in water bodies, which pose a serious environmental threat to aquatic ecosystems. This work provides a comprehensive technical, environmental and cost assessments of different advanced quaternary treatments for wastewater effluents, with special focus on novel Non-Thermal Plasma technology. For this porpouse Non-Thermal Plasma, Sand Filtration + Ozonation, Ultrafiltration, Ultrafiltration + Nanofiltration and Ultrafiltration + Reverse Osmosis technologies were compared with UV disinfection-based technology. This work applies the Life Cycle Analysis tool for the impact environmental assessment using both ReciPE 2016(H) method and, for a more detailed analysis of the contribution of pharmaceuticals to freshwater ecotoxicity category of impact, the USETOX method, which was integrated with 7 new characterisation factors. The results obtained showed overall removal efficiency of pharmaceuticals always higher than 80%, with performances in descending order of Ultrafiltration + Reverse Osmosis > Sand Filtration + Ozonation > Ultrafiltration + Nanofiltration > Non-Thermal Plasma, being Sand Filtration + Ultraviolet disinfection and standalone Ultrafiltration comparatively not suitable for pharmaceuticals removal. Regarding the target pharmaceuticals proposed on the EU Directive 271/91 revision, the Non-Thermal Plasma perform better towards venlafaxine than Sand Filtration + Ozonation, and towards diclofenac and carbamazepine than Ultrafiltration + Nanofiltration. Ultrafiltration + Nanofiltration and Non-Thermal Plasma showed better environmental performance than Sand Filtration + Ozonation and Ultrafiltration + Reverse Osmosis in 7 out of 18 categories of impact (ReciPe method), with Ultrafiltration + Nanofiltration being more advantageous than Non-Thermal Plasma in human and ecotoxicity-related categories of impact, and Non-Thermal Plasma more advantageous in Global Warming, Fossil Resource Scarcity, and Fine Particulate Matter Formation. Regrading Freshwater Ecotoxicity (USEtox method), the quaternary treatment configuration and its energy demand affect the Freshwater final value of impact more than the presence of pharmaceuticals. Under the conditions tested, the Non-Thermal Plasma provided the lower OPEX (0.24 € m-3) than other tested technologies, showing an interesting compromise between pharmaceuticals removal efficiency, environmental impacts, and economic operational cost.
Degradation of perfluoroalkyl and polyfluoroalkyl substances (PFAS) in water by use of a nonthermal plasma-ozonation cascade reactor: Role of different processes and reactive species

Changtao Chen,Chuanlong Ma,Xuetong Yang,Mikhail Gromov,Ye Tian,Kristof Demeestere,Anton Nikiforov,Stijn W.H. Van Hulle

DOI: https://doi.org/10.1016/j.cej.2024.150218

IF: 15.1

2024-03-14

Chemical Engineering Journal

Abstract:The widespread use of perfluoroalkyl and polyfluoroalkyl substances (PFAS) in the last century has caused serious pollution of water bodies around the world, threatening the health of humans and other organisms. In this work, a novel cascade reactor configuration, comprised of a dielectric barrier discharge (DBD) plasma chamber connected with an ozonation chamber was used to treat municipal secondary effluent loaded with several PFAS. The electrical energy per order (EE/O) for degradation of perfluorooctanoic acid (PFOA) and perfluorodecanoic acid (PFDA) amounts 180 and 100 kWh/m 3 , respectively. While the short-chain PFAS (perfluorobutanoic acid (PFBA), perfluorohexanoic acid (PFHxA)) were difficult to be degraded, i.e. degradation percentage < 32 % after 60 min, 80–90 % of the longer PFAS (PFOA and PFDA) were degraded within 60 min. The degradation of PFAS mainly occurred in the plasma chamber rather than in ozonation chamber. This is because that reductive species produced in plasma chamber, such as hydrated electrons (e aq − ) and Ar + , played a direct role in defluorination, while oxidative species, including OH, O, O 2 − , 1 O 2 , O 3 , and H 2 O 2 , has a very limited contribution for defluorination. Enhancing the utilization of reductive species is crucial to degrade PFAS. Perfluoroalkyl carboxylic acids (PFCA) generated during the plasma reactions may have a potential risk for environment. As such, further optimization should focus on full mineralization. This study provides an approach to solve the problem of PFAS-contaminated wastewater, which is of the importance to promote the application of nonthermal plasma technique in water treatment.

engineering, chemical, environmental
Plasma-aerosol-assisted interface engineering of nanofiltration membranes to improve removal of organic pollutants from water

Chuanlong Ma,Changtao Chen,Anton Nikiforov,Ardiana Kajtazi,Mei An,Leonardo Gutierrez,Arnout D’Haese,Karen Leus,Pascal Van Der Voort,Frederic Lynen,Arne Verliefde,Emile Cornelissen,Kostya (Ken) Ostrikov,Nathalie De Geyter,Rino Morent

DOI: https://doi.org/10.1016/j.cej.2024.153755

IF: 15.1

2024-07-14

Chemical Engineering Journal

Abstract:Membrane surface functionalization has shown great potential in improving the removal of organic pollutants from water by nanofiltration (NF). However, conventional surface modification methods rely on hazardous chemical solutions and produce large amounts of wastewater, which is contrary to the original purpose of wastewater remediation and the current high demand for environmental sustainability. Herein, we demonstrate a solvent-free and scalable method enabled by an emerging aerosol-assisted plasma deposition process for surface functionalization of NF membranes to improve the removal of organic pollutants from water. We first investigate the physicochemical properties of the aerosol-assisted plasma deposited (3-aminopropyl)triethoxysilane (AAPD-APTES) and 2-hydroxyethyl methacrylate (AAPD-HEMA) coatings on commercial NF270 membranes by different surface characterization techniques. Then, we examine the associated membranes' performance in removing conventional organic pollutants (phenol) and emerging micropollutants (diuron). Compared to the untreated NF270 membranes (2.9% for phenol and 22.0% for diuron), AAPD-APTES-modified NF270 membranes have the highest rejection efficiency towards both phenol (68.5%) and diuron (49.1%), whereas AAPD-HEMA coated membranes show good selectivity behavior with a high rejection efficiency for diuron (43.6%) but a relatively low efficiency for phenol (6.2%). Both plasma polymer-coated membranes are effective in removing organic contaminants mainly due to the plasma-produced dense surface coatings. Overall, this study offers a comprehensive eco-friendly and scalable strategy for NF membrane surface functionalization, which can not only improve the NF performance in wastewater remediation but also reduce the production of wastewater in the surface functionalization process.

engineering, chemical, environmental
Electrochemical degradation of herbicide diuron on flow-through electrochemical reactor and CFD hydrodynamics simulation

Yapeng He,Panpan Zhang,Hui Huang,Xue Wang,Buming Chen,Zhongcheng Guo,Haibo Lin

DOI: https://doi.org/10.1016/j.seppur.2020.117284

IF: 8.6

2020-11-01

Separation and Purification Technology

Abstract:An energy-efficient continuous flow-through electrochemical reactor (FT-ER) equipped with PbO2 filter anodes is designed and employed for electrochemical elimination towards herbicide diuron in the aquatic environment. Boosting performances, including substantially higher electrochemical mineralization kinetics and lower energy consumption, could be realized on the FT-ER compared with the traditional flow-by model. The effect of current density and flow rate on the degradation efficiency is also investigated. The glorious degradation kinetics could be ascribed to the large electrochemical surface area, strong generation power of reactive oxidants, and enhanced mass transfer process derived from the filter structure. Furthermore, we establish the computational fluid dynamics simulation to elucidate the dynamic flow behavior of the electrolyte, including fluid velocity and turbulent intensity distribution. The profound influence of FT-ER for the herbicide diuron removal stems from the homogenization of electrolyte flux and turbulence promoter of the filter structure. Finally, the continuous flow-through configuration exhibits excellent elimination performances, uniform fluid dynamics together with good stability. The filter anodes present a promising option for electrochemical treatment towards diverse organic pollutants in the aquatic environment and would be benefit to the evolution of cost-efficient electrochemical treatment techniques and reactors.

engineering, chemical
Styrene and Bioaerosol Removal from Waste Air with a Combined Biotrickling Filter and DBD–Plasma System

Steffen Helbich,Daniel Dobslaw,Andreas Schulz,Karl-Heinrich Engesser

DOI: https://doi.org/10.3390/su12219240

IF: 3.9

2020-11-06

Sustainability

Abstract:A combined system of a biotrickling filter and a non-thermal plasma (NTP) in a downstream airflow was operated for 1220 days for treatment of emissions of styrene and secondary emissions of germs formed in the biological process. The biotrickling filter was operated at variable inlet concentrations, empty bed residence times (EBRT), type and dosage of fertilizers, irrigation densities, and starvation periods, while dielectric barrier discharge and corona discharge were operated at different specific input energy levels to achieve optimal conditions. Under these conditions, efficiencies in the removal of volatile organic compounds (VOCs), germs and styrene of 96–98%, 1–4 log units and 24.7–50.1 g C m−3 h−1 were achieved, respectively. Fluid simulations of the NTP and a germ emission-based clocking of the discharge reveal further energy saving potentials of more than 90%. The aim of an energy-efficient elimination of VOCs through a biotrickling filter and of secondary germ emissions by a NTP stage in a downstream airflow for potential re-use of purified waste gas as process gas for industrial application was successfully accomplished.

environmental sciences,environmental studies,green & sustainable science & technology
Performance assessment of up-flow anaerobic multi-staged reactor followed by auto-aerated immobilized biomass unit for treating polyester wastewater, with biogas production

Raouf Hassan,Karim Kriaa,Amr M. Wahaballa,Mahmoud Elsayed,M. Mahmoud,Mahmoud Nasr,Ahmed Tawfik

DOI: https://doi.org/10.1007/s13201-024-02129-y

IF: 5.411

2024-03-14

Applied Water Science

Abstract:Abstract Polyester manufacturing industries produce highly polluted effluents, containing organics, nutrients, trace metals, and 1,4-dioxane, requiring a high degree of treatment before being discharged into the water bodies. This study focused on removing complex pollutants from a diluted polyester industrial effluent (DPIE) via a cost-efficient anaerobic/aerobic combined system, with biogas recovery. The integrated pilot-scale system was composed of an up-flow anaerobic multi-staged reactor (UASR; V = 41 L) followed by an auto-aerated immobilized biomass (AIB; V sponge = 9.54 L) unit and operated at a total organic loading rate (OLR) of 0.75 ± 0.16 g COD/L/d and pH of 7.14 ± 0.14 at 25 °C. The UASR achieved removal efficiencies of 17.82 ± 3.14% and 15.90 ± 3.08% for chemical oxygen demand (COD, total and soluble) and 15.83 ± 4.68% for total Kjeldahl nitrogen (TKN), with bio-CH 4 yield of 263.24 ± 31.98 mL/g COD. Adding the AIB unit improved the overall COD total , COD soluble , and TKN to 93.94 ± 2.39%, 94.84 ± 2.23%, and 75.81 ± 3.66%, respectively. The NH 4 -N removal efficiency was 85.66 ± 2.90% due to the oxic/nitrification condition on the sponge’s outer surface. The entire system also achieved 73.26 ± 2.68%, 77.48 ± 5.74%, and 81.26 ± 6.17% removals for Fe (3.93 ± 0.95 ppm), Zn (5.92 ± 2.32 ppm), and 1,4 dioxane (2.50 ± 0.61 ppm). Moreover, the UASR-AIB maintained removal efficiencies of 76.53 ± 8.47% and 77.51 ± 7.38% for total suspended solids (TSS: 335.95 ± 42.84 mg/L) and volatile suspended solids (VSS: 263.50 ± 36.94 mg/L). Regarding the DPIE toxicity level, the EC 50 value increased from 12.9 to 39.4% after UASR/AIB application. The UASR’s microbial community at the genus level demonstrated that the synergistic cooperation of solubilization, hydrolysis, acidogenesis, acetogenesis, and methanogenesis was responsible for the degradation of DPIE components.

water resources
Development and optimization of low power non-thermal plasma jet operational parameters for treating dyes and emerging contaminants

Deepchandra Joshi,G. Veda Prakash Shaikh Ziauddin Ahammad,Satyananda Kar,T R Sreekrishnan

DOI: https://doi.org/10.48550/arXiv.2212.13073

2022-12-26

Plasma Physics

Abstract:Emerging contaminants (ECs) have come out as the latest class of environmental contaminants, which are highly recalcitrant and toxic in nature. Currently, no suitable rectification methods are available against the ECs, resulting in a continuous increase in their concentration. Non-thermal plasma, as an advanced oxidation process, has been emerging as a promising technology against the ECs treatment. In the present work, a detailed experimental study is carried out to evaluate the efficacy of a non-thermal plasma jet with two dyes, Rhodamine B and Methylene Blue, as model contaminants. The plasma jet provided a complete dye decoloration in 30 min with an applied voltage of 6.5 kV. .OH, having the highest oxidation potential, acts as the main reactive species, which with direct action on contaminants also acts indirectly by getting converted into H2O2 and O3. Further, the effect of critical operational parameters viz., sample pH, applied voltage (4.5-6.5 kV), conductivity (5-20 mScm-1), and sample distance on plasma treatment efficacy was also examined. Out of all the assessed parameters, the applied voltage and sample conductivity was found to be the most significant operating parameter. A high voltage and low conductivity were found to favor the dye decoloration, while the pH effect was not that significant. To understand the influence of plasma discharge gas on treatment efficacy, all the experiments are conducted with Argon and Helium gases under the fixed geometrical configuration. Both the gases provided a similar dye decoloration efficiency. The DBD plasma system with complete dye removal also rendered maximum mineralization of 73 % for Rd. B, and 60 % for Met. Blue. Finally, the system's efficiency against the actual ECs (four pharmaceutical compounds, viz., metformin, atenolol, acetaminophen, and ranitidine) and microbial contaminant (Escherichia coli) was also tested.

Enabling Dynamic Security Policy in the Java Security Manager

An Energy Efficient Process for Degrading Perfluorooctanoic Acid (PFOA) Using Strip Fountain Dielectric Barrier Discharge Plasma

Degradation of Nitenpyram Pesticide in Aqueous Solution by Low-Temperature Plasma

Degradation of Methylene Blue by Dielectric Barrier Discharge Plasma Coupled with Activated Carbon Supported on Polyurethane Foam

Effect of dielectric barrier discharge plasma on persulfate activation for rapid degradation of atrazine: Optimization, mechanism and energy consumption

Removal of disinfection byproducts through integrated adsorption and reductive degradation in a membrane-less electrochemical system

Plasma-microbubble treatment and sustainable agriculture application of diclofenac-contaminated wastewater

A Biphasic Plasma Microreactor for Pollutants Degradation in Water

Removal of persistent organic contaminants from wastewater using a hybrid electrochemical-granular activated carbon (GAC) system

Cold atmospheric plasma technology for removal of organic micropollutants from wastewater—a review

Optimization of a Low-Cost Corona Dielectric-Barrier Discharge Plasma Wastewater Treatment System through Central Composite Design/Response Surface Methodology with Mechanistic and Efficiency Analysis

Efficient treatment of bio-contaminated wastewater using plasma technology for its reuse in sustainable agriculture

Effects of sodium persulfate and persulfate on the degradation of 2,4- dichlorophenol in a dielectric barrier discharge reactor

Destruction of n -hexane from the air stream by pulsed discharge plasma: Modelling and key process parameters optimization by CCD-RSM

Comparative life cycle assessment of non-thermal plasma for the removal of pharmaceuticals from wastewater

Degradation of perfluoroalkyl and polyfluoroalkyl substances (PFAS) in water by use of a nonthermal plasma-ozonation cascade reactor: Role of different processes and reactive species

Plasma-aerosol-assisted interface engineering of nanofiltration membranes to improve removal of organic pollutants from water

Electrochemical degradation of herbicide diuron on flow-through electrochemical reactor and CFD hydrodynamics simulation

Styrene and Bioaerosol Removal from Waste Air with a Combined Biotrickling Filter and DBD–Plasma System

Performance assessment of up-flow anaerobic multi-staged reactor followed by auto-aerated immobilized biomass unit for treating polyester wastewater, with biogas production

Development and optimization of low power non-thermal plasma jet operational parameters for treating dyes and emerging contaminants