Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Hybrid bio-inspired metaheuristic approach for design compressive strength of high-strength concrete-filled high-strength steel tube columns

High strength steel square and rectangular tubular stub columns infilled with concrete

Numerical Investigation on Compressive Performance of CFST Columns with Encased Built-Up Lattice-Angles

Behavior and Design of Slender Concrete-Filled Wide Rectangular Steel Tubular Columns under Axial Compression

Experimental and numerical investigation of square concrete-filled double-skin steel stiffened tubular stub columns with CHS inner tubes under axial compression

Mechanical behavior of high-strength concrete filled high-strength steel tubular stub columns stiffened with encased I-shaped CFRP profile under axial compression

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Numerical investigation and design of concrete-filled double square steel tube columns under axial compression

Experimental and Numerical Study of the Behavior of Concrete-Filled High-Strength Steel Tube Columns with Large D/t Ratio under Axial Compression

Strength, Stiffness and Ductility of Concrete-Filled Steel Columns under Axial Compression

Experimental and numerical behavior of eccentrically loaded square concrete-filled steel tubular long columns made of high-strength steel and concrete

Performance evaluation of composite concrete-filled steel tube columns by steel fibers and different cross-section shapes: Experimental and numerical investigations

Compressive behaviour of circular CFDST short columns with high- and ultrahigh-strength concrete

Experimental and numerical investigation on the behaviour of square concrete-filled cold-formed double-skin steel stiffened tubular short columns

Mechanical behavior and design applicability of ultra-high-performance concrete-filled circular steel tubular short columns under axial compression

Performance of CFDST stub columns using high-strength steel subjected to axial compression

Bearing behavior of high-performance concrete-filled high-strength steel tube composite columns subjected to eccentrical load

Experimental study on square concrete-filled double skin steel tubular short columns

Unified numerical model for performance analysis of various cross-sections of concrete-filled stainless-steel tubular stub columns under axial loading

Performance test and Finite-element analysis of high strength concrete-filled steel tubular columns under axial compression

Simulation of uniaxially compressed square ultra-high-strength concrete-filled steel tubular slender beam-columns