The developmental rate ofEuphausia crystallorophias larvae in Ellis Fjord, Vestfold Hills, Antarctica

J. Kirkwood

DOI: https://doi.org/10.1007/BF02329073

1996-08-01

Polar Biology

Abstract:

What problem does this paper attempt to address?

Development of high strength and ductile Zn-Al-Li alloys for potential use in bioresorbable medical devices

Ehsan Farabi,Julie A Sharp,Alireza Vahid,Daniel M Fabijanic,Matthew R Barnett,Santiago Corujeira Gallo

DOI: https://doi.org/10.1016/j.msec.2021.111897

Abstract:A series of Zn-Al-Li alloys with potential application in bioresorbable implants were cast, thermomechanically processed and tested. The formation of secondary phases, such as LiZn4, LiZn3Al and Al3Li, contributed to both dynamic recrystallization and grain refinement of the matrix (η-phase) during the hot-extrusion process, leading to grain sizes as small as 1.75 μm for Zn-4Al-0.6Li alloy (wt%). This alloy exhibited an ultimate tensile strength (UTS) of 451 MPa, a total elongation of 46% and a corrosion rate of 60 μm/year in simulated body fluid. The grain refinement played a major role in increasing the strength, but it also weakened the basal texture and promoted non-basal slip and grain boundary sliding, thus contributing to the increased plastic deformation of the alloy. The corrosion rate was affected by a layer of zinc oxide and phosphate formed in the early stages of the immersion tests. The corrosion products protected the substrate and tended to reduce the corrosion rate over time. The developed Zn-4Al-0.6Li and Zn-6Al-0.4Li alloys which showed promising mechanical and corrosion properties appeared to be cytocompatible in the mouse fibroblast cell line and human umbilical mesenchymal stem cells making them promising candidates for bioresorbable stent and implant applications.
Corrosion behavior and biocompatibility evaluation of a novel zinc-based alloy stent in rabbit carotid artery model.

Xiaolin Ran,Qilong Wang,Xinhao Yan,Guixue Wang,T. Yin,Song Lin,Wenhua Yan,T. Hu,Jack G. Zhou

DOI: https://doi.org/10.1002/jbm.b.34274

2018-11-08

Abstract:Zinc (Zn) and its alloys have been proved to be promising candidate materials for biodegradable cardiovascular stents. In this study, a novel extruded Zn-0.02 Mg-0.02Cu alloy was prepared. Compared with pure Zn, the Zn-based alloy showed higher mechanical properties, and the Zn-based alloy could significantly accelerate Zn2+ release, reaching 0.61 ± 0.11 μg/mL at 15 days of immersion. In vitro biocompatibility studies demonstrated that the Zn-based alloy had excellent cytocompatibility and hemocompatibility, including low hemolysis rate (0.63 ± 0.12%) and strong inhibitory effect on platelet adhesion. Subsequently, the Zn-based alloy stent was implanted into the left carotid arteries of New Zealand white rabbits for 12 months. All the rabbits survived without any adverse clinical events, and all the stented arteries were patent during the study period. Rapid endothelialization at 1 week of implantation was observed, suggesting a low cytotoxicity and thrombosis risk. The stent corroded slowly and no obvious intimal hyperplasia was observed for 6 months, after which corrosion accelerated at 12 months. In addition, no obvious thrombosis and systemic toxicity during implantation period were observed, indicating its potential as the backbone of biodegradable cardiovascular stents. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: 00B: 000-000, 2018.

Medicine,Materials Science,Engineering
Developing Zn-2Cu-xLi (x < 0.1 wt %) alloys with suitable mechanical properties, degradation behaviors and cytocompatibility for vascular stents

Xiyuan Zhang,Jialin Niu,Kelvin Wai-Kwok Yeung,Hua Huang,Zhiqiang Gao,Chun Chen,Qingqing Guan,Guangjian Zhang,Linlin Zhang,Guanhua Xue,Guangyin Yuan

DOI: https://doi.org/10.1016/j.actbio.2024.06.007

2024-06-12

Abstract:Biodegradable Zn alloys show great potential for vascular stents due to their moderate degradation rates and acceptable biocompatibility. However, the poor mechanical properties limit their applications. In this study, low alloyed Zn-2Cu-xLi (x = 0.004, 0.01, 0.07 wt %) alloys with favorable mechanical properties were developed. The microstructure consists of fine equiaxed η-Zn grains, micron, submicron-sized and coherent nano ε-CuZn4 phases. The introduced Li exists as a solute in the η-Zn matrix and ε-CuZn4 phase, and results in the increase of ε-CuZn4 volume fraction, the refinement of grains and more uniform distribution of grain sizes. As Li content increases, the strength of alloys is dramatically improved by grain boundary strengthening, precipitate strengthening of ε-CuZn4 and solid solution strengthening of Li. Zn-2Cu-0.07Li alloy has the optimal mechanical properties with a tensile yield strength of 321.8 MPa, ultimate tensile strength of 362.3 MPa and fracture elongation of 28.0 %, exceeding the benchmark of stents. It also has favorable mechanical property stability, weak tension compression yield asymmetry and strain rate sensitivity. It exhibits uniform degradation and a little improved degradation rate of 89.5 μm∙year-1, due to the improved electrochemical activity by increased ε-CuZn4 volume fraction, and generates Li2CO3 and LiOH. It shows favorable cytocompatibility without adverse influence on endothelial cell viability by trace Li+. The fabricated microtubes show favorable mechanical properties, and stents exhibit an average radial strength of 118 kPa. The present study indicates that Zn-2Cu-0.07Li alloy is a potential and promising candidate for vascular stent applications. STATEMENT OF SIGNIFICANCE: Zn alloys are promising candidates for biodegradable vascular stents. However, improving their mechanical properties is challenging. Combining the advantages of Cu and trace Li, Zn-2Cu-xLi (x < 0.1 wt %) alloys were developed for stents. As Li increases, the strength of alloys is dramatically improved by refined grains, increased volume fraction of ε-CuZn4 and solid solution of Li. Zn-2Cu-0.07Li alloy exhibits a TYS exceeding 320 MPa, UTS exceeding 360 MPa and fracture EL of nearly 30 %. It shows favorable mechanical stability, degradation behaviors and cytocompatibility. The alloy was fabricated into microtubes and stents for mechanical property tests to verify application feasibility for the first time. This indicates that Zn-2Cu-0.07Li alloy has great potential for vascular stent applications.
Novel Biodegradable Zn Alloy with Exceptional Mechanical and In Vitro Corrosion Properties for Biomedical Applications

Ehsan Farabi,Julie Sharp,Alireza Vahid,Jiangting Wang,Daniel M. Fabijanic,Matthew R. Barnett,Santiago Corujeira Gallo

DOI: https://doi.org/10.1021/acsbiomaterials.1c00763

2021-11-01

Abstract:A series of quaternary Zn-Al-Cu-Li alloys with different weight fractions of Cu, Al, and Li were developed and investigated for potential application in high load bearing bioresorbable implants. The developed alloys provided various fractions of binary and ternary intermetallic structures, which resulted in formation of multiphase microstructures containing a zinc-rich η-phase and LiZn4 and CuZn4 phases. The intermetallic phases promoted grain refinement and a good combination of mechanical properties. The developed Zn-2Al-4Cu-0.6Li alloy showed strength and ductility close to commercially pure Ti alloys with a UTS value of ∼535 MPa and elongation of 37%. The examination of in vitro corrosion behavior of the developed alloys in the modified Hanks' solution revealed suitable corrosion rates (∼38.5 μm/year). The moderate corrosion rate was controlled by the formation of a homogeneous layer of stable corrosion products that protected the alloys from the corrosive environment, particularly in the late stages of immersion. The developed alloys with the most promising mechanical and corrosion properties appeared to be biocompatible to mouse fibroblast cells and human umbilical mesenchymal stem cells, making them suitable candidates for implant applications.

materials science, biomaterials
In Vitro Evaluation of the Feasibility of Commercial Zn Alloys As Biodegradable Metals

C. Wang,H. T. Yang,X. Li,Y. F. Zheng

DOI: https://doi.org/10.1016/j.jmst.2016.06.003

2016-01-01

Journal of Material Science and Technology

Abstract:In this work, three widely used commercial Zn alloys（ZA4-1, ZA4-3, ZA6-1） were purchased and prepared by hot extrusion at 200 °C. The microstructure, mechanical properties, corrosion behaviors,biocompatibility and hemocompatibility of Zn alloys were studied with pure Zn as control. Commercial Zn alloys demonstrated increased strength and superb elongation compared with pure Zn. Accelerated corrosion rates and uniform corrosion morphologies were observed in terms of commercial Zn alloys due to galvanic effects between Zn matrix and α-Al phases. 100% extracts of ZA4-1 and ZA6-1 alloys showed mild cytotoxicity while 50% extracts of all samples displayed good biocompatibility. Retardant cell cycle and inhibited stress fibers expression were observed induced by high concentration of Zn 2+ releasing during corrosion. The hemolysis ratios of Zn alloys were lower than 1% while the adhered platelets showed slightly activated morphologies. In general, commercial Zn alloys possess promising mechanical properties, appropriate corrosion rates, significantly improved biocompatibility and good hemocompatibility in comparison to pure Zn. It is feasible to develop biodegradable metals based on commercial Zn alloys.
Creep properties of biodegradable Zn-0.1Li alloy at human body temperature: implications for its durability as stents

Suming Zhu,Chengcheng Wu,Guannan Li,Yufeng Zheng,Jian-Feng Nie

DOI: https://doi.org/10.1080/21663831.2019.1610106

2019-05-09

Materials Research Letters

Abstract:In recent years, zinc and its alloys have received increasing attention as a class of biodegradable materials due to their good biocompatibility and biodegradability [<a href="#">1</a> Bowen PK, Drelich J, Goldman J. Zinc exhibits ideal physiological corrosion behavior for bioabsorbable stents. Adv Mater. 2013;25:2577–2582. doi: 10.1002/adma.201300226<a href="/servlet/linkout?suffix=CIT0001&dbid=16&doi=10.1080%2F21663831.2019.1610106&key=10.1002%2Fadma.201300226">[Crossref]</a>, <a href="/servlet/linkout?suffix=CIT0001&dbid=8&doi=10.1080%2F21663831.2019.1610106&key=23495090">[PubMed]</a>, <a href="/servlet/linkout?suffix=CIT0001&dbid=128&doi=10.1080%2F21663831.2019.1610106&key=000318503600009">[Web of Science ®]</a> , <a href="http://scholar.google.com/scholar_lookup?hl=en&publication_year=2013&pages=2577-2582&author=PK+Bowen&author=J+Drelich&author=J.+Goldman&title=Zinc+exhibits+ideal+physiological+corrosion+behavior+for+bioabsorbable+stents">[Google Scholar]</a>]. Since pure Zn has poor mechanical properties that cannot meet the benchmark requirements for biomedical applications, i.e. yield strength >200 MPa, ultimate tensile strength >300 MPa, elongation > 15-18% [<a href="#">2</a> Werkhoven RJ, Sillekens WH, van Lieshout JBJM. Processing aspects of magnesium alloy stent tube. In: Sillekens WH, Agnew SR, Neelameggham NR, Mathaudhu SN, editor. Magnesium technology 2011. Cham: Springer; 2016. p. 419–424. <a href="http://scholar.google.com/scholar_lookup?hl=en&publication_year=2016&pages=419-424&author=RJ+Werkhoven&author=WH+Sillekens&author=JBJM.+van+Lieshout&title=Magnesium+technology+2011">[Google Scholar]</a>], the research efforts have been directed to enhancing the mechanical properties by alloying with other biocompatible elements, such as Li [<a href="#">3</a> Zhao S, Seitz J-M, Eifler R, et al. Zn-Li alloy after extrusion and drawing: structural, mechanical characterization, and biodegradation in abdominal aorta of rat. Mater Sci Eng C. 2017;76:301–312. doi: 10.1016/j.msec.2017.02.167<a href="/servlet/linkout?suffix=CIT0003&dbid=16&doi=10.1080%2F21663831.2019.1610106&key=10.1016%2Fj.msec.2017.02.167">[Crossref]</a>, <a href="/servlet/linkout?suffix=CIT0003&dbid=8&doi=10.1080%2F21663831.2019.1610106&key=28482531">[PubMed]</a>, <a href="/servlet/linkout?suffix=CIT0003&dbid=128&doi=10.1080%2F21663831.2019.1610106&key=000405541600037">[Web of Science ®]</a> , <a href="http://scholar.google.com/scholar_lookup?hl=en&publication_year=2017&pages=301-312&author=S+Zhao&author=J-M+Seitz&author=R+Eifler&title=Zn-Li+alloy+after+extrusion+and+drawing%3A+structural%2C+mechanical+characterization%2C+and+biodegradation+in+abdominal+aorta+of+rat">[Google Scholar]</a>,<a href="#">4</a> Zhao S, McNamara CT, Bowen PK, et al. Structural characteristics and in vitro biodegradation of a novel Zn-Li alloy prepared by induction melting and hot rolling. Metall Mater Trans A. 2017;48:1204–1215. doi: 10.1007/s11661-016-3901-0<a href="/servlet/linkout?suffix=CIT0004&dbid=16&doi=10.1080%2F21663831.2019.1610106&key=10.1007%2Fs11661-016-3901-0">[Crossref]</a> , <a href="http://scholar.google.com/scholar_lookup?hl=en&publication_year=2017&pages=1204-1215&author=S+Zhao&author=CT+McNamara&author=PK+Bowen&title=Structural+characteristics+and+in+vitro+biodegradation+of+a+novel+Zn-Li+alloy+prepared+by+induction+melting+and+hot+rolling">[Google Scholar]</a>], Mg [<a href="#">5–8</a> Vojtech D, Kubasek J, Serak J, et al. Mechanical and corrosion properties of newly developed biodegradable Zn-based alloys for bone fixation. Acta Biomater. 2011;7:3515–3522. doi: 10.1016/j.actbio.2011.05.008 Jin H, Zh-Abstract Truncated-

materials science, multidisciplinary
Fabrication and characterization of biodegradable Zn-Cu-Mn alloy micro-tubes and vascular stents: Microstructure, texture, mechanical properties and corrosion behavior

Jimiao Jiang,Hua Huang,Jialin Niu,Donghui Zhu,Guangyin Yuan

DOI: https://doi.org/10.1016/j.actbio.2022.07.049

2022-10-01

Abstract:Zinc (Zn) alloys are a promising biodegradable material for vascular stent applications. This study aimed to fabricate biodegradable Zn-2.0Cu-0.5Mn alloy micro-tubes and vascular stents with high dimensional accuracy and suitable mechanical properties, and to investigate their microstructure, texture, mechanical properties and corrosion behavior. The micro-tubes and vascular stents were successfully fabricated by a combined process of extrusion, drawing, laser cutting and electrochemical polishing. The microstructures of as-extruded and as-drawn micro-tubes consisted of Zn matrix with near-equiaxed grains (average grain size: ∼2 µm) and second phases of ε (CuZn4) and MnZn13 with different sizes. The texture evolved from basal planes approximately paralleling to deformation direction for as-extruded micro-tube to approximately perpendicular to deformation direction for as-drawn micro-tube, because predominant deformation mechanisms changed from basal <a> dislocation slip during tube extrusion to prismatic <a> dislocation, pyramidal <c+a> dislocations, and {101¯2} twins during tube drawing. As-drawn micro-tube exhibited suitable mechanical properties with an ultimate tensile strength of about 298 MPa and elongation of about 26% as a stent material. Moreover, the processed stent with a thickness of about 125 µm possessed sufficient radial strength of about 150 kPa and good balloon expandability. In addition, as-drawn tube exhibited an in vitro corrosion rate of about 158 µm/year with a basically uniform corrosion morphology. These results indicated that biodegradable Zn-2.0Cu-0.5Mn alloy is a promising vascular stent material candidate, and the procedure for processing the micro-tube and stent is practical and effective. STATEMENT OF SIGNIFICANCE: Fabrication of micro-tubes followed by laser cutting and polishing is a common way to prepare metallic vascular stents. However, it is quite challenging to fabricate Zn-based stents using this standard method, and there is a lack of studies reporting processing details in the past. Biodegradable Zn-2.0Cu-0.5Mn alloy micro-tubes and vascular stents with high dimensional accuracy and suitable mechanical properties were successfully fabricated by a combined process in this study. As-drawn micro-tube exhibited an ultimate tensile strength of about 298 MPa and elongation of about 26%. The stent possessed sufficient radial strength of about 150 kPa and good balloon expandability. We demonstrated a practical method to fabricate biodegradable Zn-based micro-tubes and stents with high dimensional accuracy and mechanical properties.
Study on the Mg-Li-Zn Ternary Alloy System with Improved Mechanical Properties, Good Degradation Performance and Different Responses to Cells.

Yang Liu,Yuanhao Wu,Dong Bian,Shuang Gao,Sander Leeflang,Hui Guo,Yufeng Zheng,Jie Zhou

DOI: https://doi.org/10.1016/j.actbio.2017.08.021

IF: 10.633

2017-01-01

Acta Biomaterialia

Abstract:Novel Mg -(3.5, 6.5 wt%)Li-(0.5, 2, 4 wt%)Zn ternary alloys were developed as new kinds of biodegradable metallic materials with potential for stent application. Their mechanical properties, degradation behavior, cytocompatibility and hemocompatibility were studied. These potential biomaterials showed higher ultimate tensile strength than previously reported binary Mg -Li alloys and ternary Mg -Li -X (X = Al, Y, Ce, Sc, Mn and Ag) alloys. Among the alloys studied, the Mg-3.5Li-2Zn and Mg-6.5Li-2Zn alloys exhibited comparable corrosion resistance in Hank's solution to pure magnesium and better corrosion resistance in a cell culture medium than pure magnesium. Corrosion products observed on the corroded surface were composed of Mg(OH)(2), MgCO3 and Ca -free Mg/P inorganics and Ca/P inorganics. In vitro cytotoxicity assay revealed different behaviors of Human Umbilical Vein Endothelial Cells (HUVECs) and Human Aorta Vascular Smooth Muscle Cells (VSMCs) to material extracts. HUVECs showed increasing nitric oxide (NO) release and tolerable toxicity, whereas VSMCs exhibited limited decreasing viability with time. Platelet adhesion, hemolysis and coagulation tests of these Mg-Li-Zn alloys showed different degrees of activation behavior, in which the hemolysis of the Mg-3.5Li-2Zn alloy was lower than 5%. These results indicated the potential of the Mg-Li-Zn alloys as good candidate materials for cardiovascular stent applications.Statement of significanceMg-Li alloys are promising as absorbable metallic biomaterials, which however have not received significant attention since the low strength, controversial corrosion performance and the doubts in Li toxicity. The Mg-Li-Zn alloy in the present study revealed much improved mechanical properties higher than most reported binary Mg -Li and ternary Mg -Li -X alloys, with superior corrosion resistance in cell culture media. Surprisingly, the addition of Li and Zn showed increased nitric oxide release. The present study indicates good potential of Mg-Li-Zn alloy as absorbable cardiovascular stent material. (C) 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
In Vivo Evaluation of Mg-5%Zn-2%Nd Alloy as an Innovative Biodegradable Implant Material

L Elkaiam,O Hakimi,G Yosafovich-Doitch,S Ovadia,E Aghion

DOI: https://doi.org/10.1007/s10439-019-02355-5

Abstract:Mg-based alloys have been considered as potential structural materials for biodegradable implants in orthopedic and cardiovascular applications, particularly when combined with other biocompatible alloying elements. However, the performances of Mg-based alloys in in vitro conditions do not accurately reflect their behavior in an in vivo environment. As such, the present study aimed at evaluating the in vivo behavior of a novel Mg-5Zn-2Nd-0.13Y-0.35Zr alloy designated as ZE52 alloy. In vivo assessment was carried out using cylindrical disks implanted into the sub-cutaneous layer of the skin at the back midline of male Wistar rats for up to 11 weeks. Post-implantation responses evaluated included well-being behavior, blood biochemical tests and histology. The corrosion rate of the implants, expressed in terms of hydrogen gas formation, was evaluated by radiographic assessment and CT examination. Results of the well-being behavioral and blood biochemical tests indicated that the in vivo behavior of ZE52 alloy implants was similar to that of inert Ti-6Al-4V alloy implants introduced into a control group. Moreover, histological analysis did not reveal any severe inflammation, as compared to the reference alloy. However, significant sub-cutaneous gas cavities were observed, indicative of the accelerated degradation of the ZE52 alloy implants. The accelerated degradation was also manifested by the formation of alloy debris that was encapsulated within the gas cavities. Post-implantation gas bubble puncturing resulted in the complete degradation of the Mg-based implants, indicating that the inert nature of the gas prevented accelerated degradation of the alloy before it was naturally absorbed by the body.
Recent Progress on Mg- and Zn-Based Alloys for Biodegradable Vascular Stent Applications

Ying Liu,Bingheng Lu,Zhixiong Cai

DOI: https://doi.org/10.1155/2019/1310792

IF: 3.791

2019-11-05

Journal of Nanomaterials

Abstract:Currently, biodegradable metals for implantation applications are widely investigated to replace biodegradable polymeric implantations, which may cause inflammatory or adverse local tissue reactions. Amongst these metals, magnesium (Mg) and zinc (Zn) alloys with good biocompatibility, mechanical properties, and corrosion resistance are being widely investigated. In this review, the criteria for biodegradable vascular stents, and the advantages and limitations of biodegradable Mg and Zn vascular stents, are summarized and evaluated. By summarizing and discussing recent research on Mg- and Zn-based alloys used as biodegradable vascular stents, this review considered many alloys that can potentially serve as biodegradable vascular stents and suggests future research directions for the development of Mg- and Zn-based alloys as biodegradable metal stents.

materials science, multidisciplinary,nanoscience & nanotechnology
A feasibility study of biodegradable magnesium-aluminum-zinc-calcium-manganese (AZXM) alloys for tracheal stent application

Jingyao Wu,Boeun Lee,Partha Saha,Prashant N Kumta

DOI: https://doi.org/10.1177/0885328218824775

Abstract:Airway obstruction conditions are relatively rarely observed in clinical settings but nevertheless, extremely challenging to handle, especially when observed in pediatric patients. Several surgical procedures, including tracheal resection, end-to-end tracheal anastomosis, and tracheoplasty, have been developed and practised of late, to treat airway obstruction. However, the clinical outcome is typically not satisfactory due to airway restenosis conditions that develop following surgery. Various types of stents are currently available for airway stenting ranging from non-degradable silicone tubes and bio-inert metallic stents (bare or coated with polymer matrix) to hybrid silicone tubes strengthened by metallic cores, but none of the stents provides the satisfactory long-term effectiveness. Therefore, there is a significant clinical need for a biodegradable airway stent that would maintain airway patency and totally degrade over time after meeting the desired objectives. The present study aims to investigate biodegradable magnesium-aluminum-zinc-calcium-manganese (AZXM) alloy as a potential tracheal stent. The new AZXM alloy was fabricated by partially replacing aliminum in commercial AZ31 alloy with calcium. The present study demonstrates that calcium preferentially segregates along the grain boundaries as intermetallic phases (Mg2Ca) and is homogeneously distributed in the magnesium matrix. The extruded AZXM alloy showed less pitting, higher corrosion resistance in Hank's Balanced Salt Solution (HBSS) compared to the as-cast and solution-treated AZXM alloys and exhibited optimized mechanical properties. In vitro cytotoxicity evaluation using human trachea epithelial cells demonstrated excellent cyto-compatibility of AZXM alloys compared to pure Mg and commercial AZ31 validated by a very preliminary rabbit in vivo tracheal model study. Preliminary results show that the approach to use biodegradable AZXM alloys as a tracheal stent is indeed promising, although further alloy processing is required to improve the ductility needed followed by a more exhaustive in vivo study to demonstrate full viability for stent applications.
Research on a Zn-Cu alloy as a biodegradable material for potential vascular stents application

Jialin Niu,Zibo Tang,Hua Huang,Jia Pei,Hua Zhang,Guangyin Yuan,Wenjiang Ding

DOI: https://doi.org/10.1016/j.msec.2016.06.082

2016-12-01

Abstract:Zn-based alloys have been viewed as new potential materials for biodegradable implants, such as cardiovascular stents, mainly in consideration of their lower corrosion rate when compared with that of Mg alloys. In this study we developed a new Zinc-4wt.%Copper (Zn-4Cu) alloy as a biodegradable material. Hot extrusion was applied to Zn-4Cu to refine the microstructure and consequently improve its mechanical properties and corrosion resistance. After extrusion, dendritic CuZn5 phases were broken and distributed along the extrusion direction. The grains were refined obviously due to dynamical recrystallization. The yield strength (YS), ultimate tensile strength (UTS) and elongation of the as-extruded alloy are 250±10MPa, 270±10MPa and 51±2%, respectively. The corrosion rate of the as-extruded alloy in Hank's solution is about 9.41(±1.34)μmyear(-1). In vitro evaluation shows that Zn-4Cu presents acceptable toxicity to human endothelial cells, and could effectively inhibit bacteria adhesion and biofilm formation. The present study indicates that the as-extruded Zn-4Cu alloy exhibits excellent strength and ductility, uniform and slow degradation, good biocompatibility and significant antibacterial effect, which make it an excellent candidate material for biodegradable implants, especially for cardiovascular stents application.
Mechanical Property, Biocorrosion and in Vitro Biocompatibility Evaluations of Mg-Li-(Al)-(Re) Alloys for Future Cardiovascular Stent Application

W. R. Zhou,Y. F. Zheng,M. A. Leeflang,J. Zhou

DOI: https://doi.org/10.1016/j.actbio.2013.01.032

IF: 10.633

2013-01-01

Acta Biomaterialia

Abstract:Mg–Li-based alloys were investigated for future cardiovascular stent application as they possess excellent ductility. However, Mg–Li binary alloys exhibited reduced mechanical strengths due to the presence of lithium. To improve the mechanical strengths of Mg–Li binary alloys, aluminum and rare earth (RE) elements were added to form Mg–Li–Al ternary and Mg–Li–Al–RE quarternary alloys. In the present study, six Mg–Li–(Al)–(RE) alloys were fabricated. Their microstructures, mechanical properties and biocorrosion behavior were evaluated by using optical microscopy, X-ray diffraction, scanning electronic microscopy, tensile tests, immersion tests and electrochemical measurements. Microstructure characterization indicated that grain sizes were moderately refined by the addition of rare earth elements. Tensile testing showed that enhanced mechanical strengths were obtained, while electrochemical and immersion tests showed reduced corrosion resistance caused by intermetallic compounds distributed throughout the magnesium matrix in the rare-earth-containing Mg–Li alloys. Cytotoxicity assays, hemolysis tests as well as platelet adhesion tests were performed to evaluate in vitro biocompatibilities of the Mg–Li-based alloys. The results of cytotoxicity assays clearly showed that the Mg–3.5Li–2Al–2RE, Mg–3.5Li–4Al–2RE and Mg–8.5Li–2Al–2RE alloys suppressed vascular smooth muscle cell proliferation after 5day incubation, while the Mg–3.5Li, Mg–8.5Li and Mg–8.5Li–1Al alloys were proven to be tolerated. In the case of human umbilical vein endothelial cells, the Mg–Li-based alloys showed no significantly reduced cell viabilities except for the Mg–8.5Li–2Al–2RE alloy, with no obvious differences in cell viability between different culture periods. With the exception of Mg–8.5Li–2Al–2RE, all of the other Mg–Li–(Al)–(RE) alloys exhibited acceptable hemolysis ratios, and no sign of thrombogenicity was found. These in vitro experimental results indicate the potential of Mg–Li–(Al)–(RE) alloys as biomaterials for future cardiovascular stent application and the worthiness of investigating their biodegradation behaviors in vivo.
Microstructure, Mechanical Properties and Creep Behaviour of Extruded Zn-xLi (x = 0.1, 0.3 and 0.4) Alloys for Biodegradable Vascular Stent Applications

Suming Zhu,Chengcheng Wu,Guannan Li,Yufeng Zheng,Jian-Feng Nie

DOI: https://doi.org/10.1016/j.msea.2020.139082

2020-01-01

Abstract:Zn-Li alloys have been shown to be promising for biodegradable vascular stent applications due to their favourable biocompatibility and superior strength. This work presents a thorough evaluation of the microstructure, room temperature mechanical properties and human body temperature creep behaviour of hot-extruded Zn-xLi (x = 0.1, 0.3 and 0.4) alloys. All alloys show typical basal texture after the extrusion but the recrystallized grains are much finer with increasing Li content. Consequently, not only the room temperature yield and tensile strengths but also the elongation to fracture is significantly increased with increasing Li content. However, increasing Li content has an adverse effect on the creep resistance at human body temperature. Moreover, there is a transition in the operative creep mechanism from dislocation creep in the Zn-0.1Li alloy to grain boundary sliding in the Zn-0.3Li and Zn-0.4Li alloys. The observed mechanical behaviour in these alloys can be well related to the grain size effect, i.e. strengthening to softening by grain boundaries with decreasing strain rate. This work suggests that grain size of biodegradable zinc alloys should be optimized in order to achieve a balance between room temperature mechanical properties and human body temperature creep resistance.
Microstructure, Mechanical Properties, in Vitro Degradation and Cytotoxicity Evaluations of Mg–1.5Y–1.2Zn–0.44Zr Alloys for Biodegradable Metallic Implants

Jun Fan,Xin Qiu,Xiaodong Niu,Zheng Tian,Wei Sun,Xiaojuan Liu,Yangde Li,Weirong Li,Jian Meng

DOI: https://doi.org/10.1016/j.msec.2013.01.063

2013-01-01

Abstract:Mg-1.5Y-1.2Zn-0.44Zr alloys were newly developed as degradable metallic biomaterials. A comprehensive investigation of the microstructure, mechanical properties, in vitro degradation assessments and in vitro cytotoxicity evaluations of the as-cast state, as-heat treated state and as-extruded state alloys was done. The microstructure observations show that the Mg-1.5Y-1.2Zn-0.44Zr alloys are mainly composed of the matrix α-Mg phases and the Mg12ZnY secondary phases (LPS structure). The hot extrusion method significantly refined the grains and eliminated the defects of both as-cast and heat treated alloys and thereby contributed to the better mechanical properties and biodegradation resistance. The values of tensile strength and tensile yield strength of the alloy in the as-extruded condition are about 236 and 178 MPa respectively, with an excellent elongation of 28%. Meanwhile, the value of compressive strength is about 471 MPa and the value of bending strength is about 501 MPa. The superior bending strength further demonstrates the excellent ductility of the hot extruded alloys. The results of immersion tests and electrochemical measurements in the SBF indicate that a protective film precipitated on the alloy's surface with the extension of degradation. The protective film contains Mg(OH)2 and hydroxyapatite (HA) which can reinforce osteoblast activity and promote good biocompatibility. No significant cytotoxicity towards L-929 cells was detected and the immersion extracts of alloy samples could enhance the cell proliferation with time in the cytotoxicity evaluations, implying that the Mg-1.5Y-1.2Zn-0.44Zr alloys have the potential to be used for biomedical applications.
In vitro cytocompatibility, hemocompatibility and antibacterial properties of biodegradable Zn-Cu-Fe alloys for cardiovascular stents applications

Rui Yue,Jialin Niu,Yutong Li,Guizhou Ke,Hua Huang,Jia Pei,Wenjiang Ding,Guangyin Yuan

DOI: https://doi.org/10.1016/j.msec.2020.111007

Abstract:In the present study, the effects of Zn-3Cu-xFe (x = 0, 0.2, 0.5 wt%) alloys on endothelial cells (EA.hy926) and smooth muscle cells (A7r5), the hemocompatibility and antibacterial properties were also evaluated. The cell viability of EA.hy926 cells and A7r5 cells decreased with the increasing of extract concentration. At the same Zn2+ concentration (over 6 ppm), the cell viability of EA.hy926 cells increased with the addition of Cu or Cu and Fe content, but no significant effect on A7r5 cells was observed. The hemolysis rate of Zn-3Cu-xFe alloys samples was about 1%, and there was no adversely affected on platelets adhering to the surface of the Zn alloys. As Fe content increases in the Zn-Cu-Fe alloys, the antibacterial lower concentrations against Staphylococcus aureus and Escherichia coli was improved due to the higher degradation rate and more Zn2+ and Cu2+ released. Our previous study already showed that the Zn-Cu-Fe alloy exhibited excellent mechanical properties and moderate degradation rate. Based on the above results, the in vitro biocompatibilities and antibacterial properties of Zn-3Cu alloy are significantly improved by the alloying of trace Fe, and the hemocompatibility is not adversely affected, which indicated that Zn-Cu-Fe alloy is a promising vascular stents candidate material.
Enhanced in Vitro and in Vivo Performance of Mg-Zn-Y-Nd Alloy Achieved with Aptes Pretreatment for Drug-Eluting Vascular Stent Application

Jing Liu,Bo Zheng,Pei Wang,Xingang Wang,Bin Zhang,Qiuping Shi,Tingfei Xi,Ming Chen,Shaokang Guan

DOI: https://doi.org/10.1021/acsami.6b05038

IF: 9.5

2016-01-01

ACS Applied Materials & Interfaces

Abstract:Bioabsorbable magnesium alloys are becoming prominent as temporary functional implants, as they avoid the risks generated by permanent metallic implants such as persistent inflammation and late restenosis. Nevertheless, the overfast corrosion of Mg alloys under physiological conditions hinders their wider application as medical implant materials. Here we investigate a simple one-step process to introduce a cross-linked 3-amino-propyltrimethoxysilane (APTES) silane physical barrier layer on the surface of Mg-Zn-Y-Nd alloys prior to electrostatic spraying with rapamycin-eluting poly (lactic -co-glycolic acid) (PLGA) layer. Surface microstructure was characterized by scanning electron microscope and Fourier transform infrared spectroscopy. Nanoscratch test verified the superior adhesion strength of PLGA coating in the group pretreated with APTES. Electrochemical tests combined with long-term immersion results suggested that the preferable in vitro anticorrosion behavior could be achieved by dense APTES barrier. Cell morphology and proliferation data demonstrated that APTES pretreated group resulted in remarkably preferable compatibility for both human umbilical vein endothelial cells and vascular smooth muscle cells. On the basis of excellent in vitro mechenical property, the animal study on the APTES pretreated Mg-Zn-Y-Nd stent implanted into porcine coronary arteries confirmed benign tissue compatibility as well as re-endothelialization without thrombogenesis or in-stent restenosis at six-month followup.
Development and characterization of ZnxCuyTizMo alloys for biomedical applications: A high-throughput gradient continuous casting approach

Shang Dai,Luhai Liao,Muhammad Abubaker Khan,Yun Feng,Weili Yao,Jingyuan Li

DOI: https://doi.org/10.1016/j.actbio.2024.05.019

2024-07-01

Abstract:The limited mechanical properties of pure Zn, such as its low strength and ductility, hinder its application as a material for biodegradable implants. Addressing this challenge, the current study focuses on the development of biodegradable Zn-based alloys, employing innovative alloy design and processing strategies. Here, alloys with compositions ranging from 0.02 to 0.10 weight percent (wt%) Cu, 1.22 to 1.80 wt% Ti, and 0.04 to 0.06 wt% Mo were produced utilizing a high-throughput gradient continuous casting process. This study highlights three specific alloys: Zn1.82Cu0.10Ti0.05Mo (HR8), Zn0.08Cu1.86Ti0Mo (HR7), and Zn1.26Cu0.13Ti0.06Mo (HR6), which were extensively evaluated for their microstructure, mechanical properties, electrochemical performance, potential as bioimplants, and cytotoxicity. These alloys were found to exhibit enhanced mechanical strength, optimal degradation rates, and superior biocompatibility, evidenced by in-vivo experiments with SD rats, positioning them as promising candidates for medical implants. This research not only introduces a significant advancement in biodegradable alloy development but also proposes an efficient method for their production, marking a pivotal step forward in biomedical engineering. STATEMENT OF SIGNIFICANCE: The limited mechanical properties of pure Zn have hindered its application in biodegradable implants. Our research primarily focuses on the alloy design and process strategies of biodegradable Zn-based alloys. We explore the ZnCuxTixMox alloys. This study introduces a high-throughput experimental approach for efficient screening of multi-component alloy systems with optimal properties. The ZnCuxTixMox alloys were designed and processed through gradient continuous casting, followed by homogenization and hot rolling. Our findings indicate that the Zn1.82Cu0.10Ti0.05Mo alloy demonstrates superior tensile, mechanical, and corrosion properties post hot rolling. The study suggests that Zn0.13Cu1.26Ti0.06Mo, Zn0.08Cu1.86Ti0Mo, and Zn1.82Cu0.10Ti0.05Mo alloys hold significant potential as biodegradable materials.
Mechanical Analysis and Corrosion Analysis of Zinc Alloys for Bioabsorbable Implants for Osteosynthesis

Salome Hagelstein,Sergej Zankovic,Adalbert Kovacs,Roland Barkhoff,Michael Seidenstuecker

DOI: https://doi.org/10.3390/ma15020421

IF: 3.4

2022-01-06

Materials

Abstract:Zinc alloys have recently been researched intensely for their great properties as bioabsorbable implants for osteosynthesis. Pure zinc (Zn) itself has relatively poor strength, which makes it insufficient for most clinical use. Research has already proven that the mechanical strength of zinc can be enhanced significantly by alloying it with silver. This study evaluated zinc silver alloys (ZnAg) as well as novel zinc silver titanium alloys (ZnAgTi) regarding their mechanical properties for the use as bioabsorbable implants. Compared to pure zinc the mechanical strength was enhanced significantly for all tested zinc alloys. The elastic properties were only enhanced significantly for the zinc silver alloys ZnAg6 and ZnAg9. Regarding target values for orthopedic implants proposed in literature, the best mechanical properties were measured for the ZnAg3Ti1 alloy with an ultimate tensile strength of 262 MPa and an elongation at fracture of 16%. Besides the mechanical properties, the corrosion rates are important for bioabsorbable implants. This study tested the corrosion rates of zinc alloys in PBS solution (phosphate buffered solution) with electrochemical corrosion measurement. Zinc and its alloys showed favorable corrosion rates, especially in comparison to magnesium, which has a much lower degradation rate and no buildup of hydrogen gas pockets during the process. Altogether, this makes zinc alloys highly favorable for use as material for bioabsorbable implants for osteosynthesis.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Mechanical Strength, Biodegradation, and In Vitro and In Vivo Biocompatibility of Zn Biomaterials.

Donghui Zhu,Irsalan Cockerill,Yingchao Su,Zhaoxiang Zhang,Jiayin Fu,Kee-Won Lee,Jun Ma,Chuka Okpokwasili,Liping Tang,Yufeng Zheng,Yi-Xian Qin,Yadong Wang

DOI: https://doi.org/10.1021/acsami.8b20634

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Zn-based biomaterials have emerged as promising new types of bioresorbable metallics applicable to orthopedic devices, cardiovascular stents, and other medical applications recently. Compared to other degradable metallic biomaterials (i.e. Mg- or Fe-based), Zn biomaterials have a more appropriate corrosion rate without hydrogen gas evolution. Here, we evaluated the potential of Zn-based metallics as medical implants, both in vitro and in vivo, alongside a standard benchmark Mg alloy, AZ31. The mechanical properties of the pure Zn were not strong enough, but were significantly enhanced (microhardness >70 kg/mm2, strength >220 MPa, elongation >15%) after alloying with Sr or Mg (1.5 at. %), surpassing the minimal design criteria for load-bearing device applications. The corrosion rate of Zn-based biomaterials was about 0.4 mm/year, significantly slower than that of AZ31. The measured cell viability and proliferation of three different human primary cells fared better for Zn-based biomaterials than AZ31 using both direct and indirect culture methods. Platelet adhesion and activation on Zn-based materials were minimal, significantly less than on AZ31. Hemolysis ratio of red cells (<0.5%) after incubation with Zn-based materials was also well below the ISO standard of 5%. Moreover, Zn-based biomaterials promoted stem cell differentiation to induce the extracellular matrix (ECM) mineralization process. In addition, in vivo animal testing using subcutaneous, bone, and vascular implantations revealed that the acute toxicity and immune response of Zn-based biomaterials were minimal/moderate, comparable to that of AZ31. No extensive cell death and foreign body reactions were observed. Taken together, Zn-based biomaterials may have a great potential as promising candidates for medical implants.

The developmental rate ofEuphausia crystallorophias larvae in Ellis Fjord, Vestfold Hills, Antarctica

Development of high strength and ductile Zn-Al-Li alloys for potential use in bioresorbable medical devices

Corrosion behavior and biocompatibility evaluation of a novel zinc-based alloy stent in rabbit carotid artery model.

Developing Zn-2Cu-xLi (x < 0.1 wt %) alloys with suitable mechanical properties, degradation behaviors and cytocompatibility for vascular stents

Novel Biodegradable Zn Alloy with Exceptional Mechanical and In Vitro Corrosion Properties for Biomedical Applications

In Vitro Evaluation of the Feasibility of Commercial Zn Alloys As Biodegradable Metals

Creep properties of biodegradable Zn-0.1Li alloy at human body temperature: implications for its durability as stents

Fabrication and characterization of biodegradable Zn-Cu-Mn alloy micro-tubes and vascular stents: Microstructure, texture, mechanical properties and corrosion behavior

Study on the Mg-Li-Zn Ternary Alloy System with Improved Mechanical Properties, Good Degradation Performance and Different Responses to Cells.

In Vivo Evaluation of Mg-5%Zn-2%Nd Alloy as an Innovative Biodegradable Implant Material

Recent Progress on Mg- and Zn-Based Alloys for Biodegradable Vascular Stent Applications

A feasibility study of biodegradable magnesium-aluminum-zinc-calcium-manganese (AZXM) alloys for tracheal stent application

Research on a Zn-Cu alloy as a biodegradable material for potential vascular stents application

Mechanical Property, Biocorrosion and in Vitro Biocompatibility Evaluations of Mg-Li-(Al)-(Re) Alloys for Future Cardiovascular Stent Application

Microstructure, Mechanical Properties and Creep Behaviour of Extruded Zn-xLi (x = 0.1, 0.3 and 0.4) Alloys for Biodegradable Vascular Stent Applications

Microstructure, Mechanical Properties, in Vitro Degradation and Cytotoxicity Evaluations of Mg–1.5Y–1.2Zn–0.44Zr Alloys for Biodegradable Metallic Implants

In vitro cytocompatibility, hemocompatibility and antibacterial properties of biodegradable Zn-Cu-Fe alloys for cardiovascular stents applications

Enhanced in Vitro and in Vivo Performance of Mg-Zn-Y-Nd Alloy Achieved with Aptes Pretreatment for Drug-Eluting Vascular Stent Application

Development and characterization of ZnxCuyTizMo alloys for biomedical applications: A high-throughput gradient continuous casting approach

Mechanical Analysis and Corrosion Analysis of Zinc Alloys for Bioabsorbable Implants for Osteosynthesis

Mechanical Strength, Biodegradation, and In Vitro and In Vivo Biocompatibility of Zn Biomaterials.