Recent Researches on Emetine and its Value as a Therapeutic Agent in Amoebiasis and other Diseases.

G. Low

Proceedings of the Royal Society of Medicine

Abstract:

What problem does this paper attempt to address?

Modeling and Control of Differential-Drive Chassis for a Homecare Assistive Robot

Ping He,Honghao Lv,Haiteng Wu,Geng Yang

DOI: https://doi.org/10.1109/ISIE51358.2023.10228142

2023-01-01

Abstract:With the increasing of the aging population, the demand for homecare services is escalating and the homecare assistive robots are becoming increasingly popular. In this paper, a differential mobile chassis design for a homecare assistive robot is presented. The mobile chassis is made of aluminum sheet and profile, and adopts a two-wheel differential model as the kinematic model. The STM32 single chip microcomputer is used as the cerebellum to control chassis movement, and the NVIDIA Jetson Nano Developer Kit is employed as the brain for perception and decision-making. The software architecture is based on the back-fore ground system and the ROS. A prototype is developed and experiments on simultaneous localization and mapping (SLAM) as well as autonomous navigation experiments are conducted to verify the practicality of the chassis design.
Development of a Human-Robot Hybrid Intelligent System Based on Brain Teleoperation and Deep Learning SLAM

Jianlong Li,Zhijun Li,Ying Feng,Yiliang Liu,Guangming Shi

DOI: https://doi.org/10.1109/tase.2019.2911667

IF: 6.636

2019-01-01

IEEE Transactions on Automation Science and Engineering

Abstract:To achieve the better navigation performance of a mobile robot in the unknown environments, a novel human–robot hybrid system incorporating a motor-imagery (MI)-based brain teleoperation control is presented in this paper, where a deep-learning-based active perception is developed in the simultaneous localization and mapping (SLAM) framework. Using the deep-learning-based object recognition in the red–green–blue-depth (RGB-D) data acquisition process, the designed SLAM approach can select the valid feature points effectively, and the speed of displacement tracking can be improved by combining the oriented FAST and rotated BRIEF (ORB) SLAM algorithm with the optical flow method. The global trajectory map can also be mended using graph-based nonlinear error optimization. In addition, to build the connection between human intentions and the robot control commands flexibly in the developed mobile robot, a common spatial pattern (CSP)-based support vector machine (SVM) classification algorithm is proposed so that the control commands can be obtained directly from the human electroencephalograph (EEG) signals, which are preanalyzed and classified using the phenomena of event-related synchronization/desynchronization (ERS/ERD). Experiments involving several operators have verified the effectiveness of the proposed framework in the actual unstructured environments. <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">Note to Practitioners</italic> —This paper is motivated by the exploration of the mobile robots remotely controlled by the disables in an unstructured environment that includes some unknown moving objects in the background. In the conventional approaches, the image feedback and the brain–computer interface-based EEG signals invoked by the visual stimulus are used to guide the motion of the robots. In this paper, the MI of left or right hand is adopted as an input of the brain teleoperation system, and the EEG signals are classified into two categories representing two robot control commands through the designed algorithm. Besides, a deep-learning-based SLAM is designed to analyze the image and depth of the environmental information provided by the robot RGB-D sensor, and the results can be transferred into a 3-D map locating the robot and assisting the operator to understand the operating environment. It has been verified that the deep-learning-based SLAM presented is more efficient and robust than traditional SLAM. The feasibility of the system is demonstrated by a set of experiments in the corridor environment.
Systematic Odometry Error Evaluation and Correction in a Human-Sized Three-Wheeled Omnidirectional Mobile Robot Using Flower-Shaped Calibration Trajectories

Jordi Palacín,Elena Rubies,Eduard Clotet

DOI: https://doi.org/10.3390/app12052606

2022-03-02

Applied Sciences

Abstract:Odometry is a simple and practical method that provides a periodic real-time estimation of the relative displacement of a mobile robot based on the measurement of the angular rotational speed of its wheels. The main disadvantage of odometry is its unbounded accumulation of errors, a factor that reduces the accuracy of the estimation of the absolute position and orientation of a mobile robot. This paper proposes a general procedure to evaluate and correct the systematic odometry errors of a human-sized three-wheeled omnidirectional mobile robot designed as a versatile personal assistant tool. The correction procedure is based on the definition of 36 individual calibration trajectories which together depict a flower-shaped figure, on the measurement of the odometry and ground truth trajectory of each calibration trajectory, and on the application of several strategies to iteratively adjust the effective value of the kinematic parameters of the mobile robot in order to match the estimated final position from these two trajectories. The results have shown an average improvement of 82.14% in the estimation of the final position and orientation of the mobile robot. Therefore, these results can be used for odometry calibration during the manufacturing of human-sized three-wheeled omnidirectional mobile robots.
Adaptive heading correction for an industrial heavy-duty omnidirectional robot

Rocco Galati,Giacomo Mantriota,Giulio Reina

DOI: https://doi.org/10.1038/s41598-022-24270-x

2022-11-15

Abstract:The paper deals with the design and testing of a robot for industrial applications featuring omnidirectionality thanks to the use of mecanum wheels. While this architecture provides remarkable manoeuvrability in narrow or cluttered spaces, it has some drawbacks that limit its widespread deployment in practice, especially for heavy-duty and long-duration tasks. As an example, the variability in the mecanum wheel rolling radius leads to undesired dynamic ill-effects, such as slippage and vibrations that affect the accuracy of pose estimation and tracking control systems. Drawing on the modeling of the kinematic and dynamic behaviour of the robot, these effects have been tackled within an adaptive estimation framework that adjusts the robot control system based on the properties of the surface being traversed. The proposed approach has been validated in experimental tests using a physical prototype operating in real industrial settings.
Kinematic and optimal design of a three-wheeled holonomic omnidirectional robot platform for mobile manipulation tasks

Rutvik Mehenge,Niket Satoskar,Anukool Shidhore,N. Mohamed Arshath

DOI: https://doi.org/10.30574/gjeta.2023.17.1.0202

2023-10-30

Global Journal of Engineering and Technology Advances

Abstract:Mobile manipulator robots are increasingly vital in industrial and service sectors, serving roles in assembly, inspection, and hazardous environments. The integration of a manipulator with a mobile robot base imposes unique demands on the vehicle's drive system. This paper introduces a three-wheel holonomic omnidirectional robot designed for mobile applications. It explores kinematic equations, electronic integration, and mechanical design for holonomic motion. This platform excels in mobility, capable of simultaneous translation and rotation, facilitating precise multidirectional motion. Its equilateral truncated triangular structure ensures stability, supporting up to 4 kg. With three omnidirectional wheels and DC motors, controlled by EMS 30A H-Bridge and Arduino Mega 2560, it offers an open platform for research and development. This robust platform aligns kinematic calculations with mathematical models, promising efficiency for diverse mobile manipulation robot applications.
The Assistant Personal Robot Project: From the APR-01 to the APR-02 Mobile Robot Prototypes

Jordi Palacín,Elena Rubies,Eduard Clotet

DOI: https://doi.org/10.3390/designs6040066

2022-07-25

Designs

Abstract:This paper describes the evolution of the Assistant Personal Robot (APR) project developed at the Robotics Laboratory of the University of Lleida, Spain. This paper describes the first APR-01 prototype developed, the basic hardware improvement, the specific anthropomorphic improvements, and the preference surveys conducted with engineering students from the same university in order to maximize the perceived affinity with the final APR-02 mobile robot prototype. The anthropomorphic improvements have covered the design of the arms, the implementation of the arm and symbolic hand, the selection of a face for the mobile robot, the selection of a neutral facial expression, the selection of an animation for the mouth, the application of proximity feedback, the application of gaze feedback, the use of arm gestures, the selection of the motion planning strategy, and the selection of the nominal translational velocity. The final conclusion is that the development of preference surveys during the implementation of the APR-02 prototype has greatly influenced its evolution and has contributed to increase the perceived affinity and social acceptability of the prototype, which is now ready to develop assistance applications in dynamic workspaces.
Design, Assembly and Control of a Differential/Omnidirectional Mobile Robot through Additive Manufacturing

Erick Axel Padilla-García,Raúl Dalí Cruz-Morales,Jaime González-Sierra,David Tinoco-Varela,María R. Lorenzo-Gerónimo

DOI: https://doi.org/10.3390/machines12030163

IF: 2.899

2024-02-29

Machines

Abstract:Although additive manufacturing is a relatively new technology, it has been widely accepted by industry and academia due to the wide variety of prototypes that can be built. Furthermore, using mobile robots to carry out different tasks allows greater flexibility than using manipulator robots. In that sense, and based on those above, this article focuses on the design and assembly of a multi-configurable mobile robot that is capable of changing from a differential to an omnidirectional configuration. For this purpose, a sequential mechatronic design/control methodology was implemented to obtain an affordable platform via additive manufacturing which is easily scalable and allows the user to change from one configuration to another. As a proof of concept, this change is made manually. Fabrication, construction, and assembly processes for both structures are presented. Then, a hierarchical control law is designed. In this sense and based on Lyapunov's method, a low-level controller is developed to control the angular speed of the wheels to a desired angular speed, and a medium-level controller controls the robot's attitude to follow a desired Cartesian trajectory. Finally, the control strategies are implemented in both prototype configurations, and through experimental results, the theoretical analysis and the construction of the mobile robot are validated.

engineering, mechanical, electrical & electronic
The Otbot project: Dynamic modelling, parameter identification, and motion control of an omnidirectional tire-wheeled robot

Pere Giró,Enric Celaya,Lluís Ros

2023-11-18

Abstract:In recent years, autonomous mobile platforms are finding an increasing range of applications in inspection or surveillance tasks, or to the transport of objects, in places such as smart warehouses, factories or hospitals. In these environments it is useful for the robot to have omnidirectional capability in the plane, so it can navigate through narrow or cluttered areas, or make position and orientation changes without having to maneuver. While this capability is usually achieved with directional sliding wheels, this work studies a particular robot that achieves omnidirectionality using conventional wheels, which are easier to manufacture and maintain, and support larger loads in general. This robot, which we call ``Otbot'' (for omnidirectional tire-wheeled robot), was already conceived in the late 1990s, but all the controllers that have been proposed for it are based on purely kinematic models so far. These controllers may be sufficient if the robot is light, or if its motors are powerful, but on platforms that have to carry large loads, or that have more limited motors, it is necessary to resort to control laws based on dynamic models if the full acceleration capacities are to be exploited. This work develops a dynamic model of Otbot, proposes a plausible methodology to identify its parameters, and designs a control law that, using this model, is able to track prescribed trajectories in an accurate and robust manner.

Robotics
Assistant Personal Robot (APR): Conception and Application of a Tele-Operated Assisted Living Robot

Eduard Clotet,Dani Martínez,Javier Moreno,Marcel Tresanchez,Jordi Palacín

DOI: https://doi.org/10.3390/s16050610

IF: 3.9

2016-04-28

Sensors

Abstract:This paper presents the technical description, mechanical design, electronic components, software implementation and possible applications of a tele-operated mobile robot designed as an assisted living tool. This robotic concept has been named Assistant Personal Robot (or APR for short) and has been designed as a remotely telecontrolled robotic platform built to provide social and assistive services to elderly people and those with impaired mobility. The APR features a fast high-mobility motion system adapted for tele-operation in plain indoor areas, which incorporates a high-priority collision avoidance procedure. This paper presents the mechanical architecture, electrical fundaments and software implementation required in order to develop the main functionalities of an assistive robot. The APR uses a tablet in order to implement the basic peer-to-peer videoconference and tele-operation control combined with a tactile graphic user interface. The paper also presents the development of some applications proposed in the framework of an assisted living robot.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Design and Implementation of a Position, Speed and Orientation Fuzzy Controller Using a Motion Capture System to Operate a Wheelchair Prototype

Mauro Callejas-Cuervo,Aura Ximena González-Cely,Teodiano Bastos-Filho

DOI: https://doi.org/10.3390/s21134344

2021-06-25

Abstract:The design and implementation of an electronic system that involves head movements to operate a prototype that can simulate future movements of a wheelchair was developed here. The controller design collects head-movements data through a MEMS sensor-based motion capture system. The research was divided into four stages: First, the instrumentation of the system using hardware and software; second, the mathematical modeling using the theory of dynamic systems; third, the automatic control of position, speed, and orientation with constant and variable speed; finally, system verification using both an electronic controller test protocol and user experience. The system involved a graphical interface for the user to interact with it by executing all the controllers in real time. Through the System Usability Scale (SUS), a score of 78 out of 100 points was obtained from the qualification of 10 users who validated the system, giving a connotation of "very good". Users accepted the system with the recommendation to improve safety by using laser sensors instead of ultrasonic range modules to enhance obstacle detection.
A Multi-Terrain Robot Prototype With Archimedean Screw Actuators: Design, Realization, Modeling, and Control

Roza Gkliva,Walid Remmas,Simon Godon,Jaan Rebane,Kilian Ochs,Maarja Kruusmaa,Asko Ristolainen

DOI: https://doi.org/10.1109/access.2024.3426105

IF: 3.9

2024-07-19

IEEE Access

Abstract:This work introduces a robot prototype designed to explore locomotion, perception, and navigation in unstructured terrains. The focus of this paper is on the robot's locomotion, from concept design to realization, as well as modelling and control. The robot's locomotion system, comprising four individually controlled archimedean screw actuators, allows holonomic planar motion control. Testing on various yielding and hard grounds has demonstrated the system's efficacy. Additionally, 3-DOF kinematic and dynamic models were developed for pose estimation, control allocation, and numerical simulations on various terrains. Although dynamic models of archimedean screw locomotion systems have been proposed in the past, they have not been used for motion control or pose estimation. Experimental validation of the dynamic model demonstrates good performance for pose estimation, providing potential for future work on online model identification and model-based control. Furthermore, a trajectory tracking control scheme was evaluated on two distinct terrains, revealing valuable insights into the effectiveness and limitations of the proposed locomotion and trajectory tracking control scheme, and highlighting areas for future research.

computer science, information systems,telecommunications,engineering, electrical & electronic
Development of an Agile Omnidirectional Mobile Robot With GRF Compensated Wheel-leg Mechanisms for Human Environments

Seong-Ho Yun,Jaehyun Park,Jiwon Seo,Yong-Jae Kim

DOI: https://doi.org/10.1109/lra.2021.3098954

IF: 5.2

2021-10-01

IEEE Robotics and Automation Letters

Abstract:Wheeled mobile robots have been receiving continuous attention in various fields because of their stability, efficiency, and simple mechanisms. However, most of them require significantly larger occupied space than humans and have limited maneuverability in the environment for humans, such as crowded corridors, floor thresholds, ramps, and elevators. This letter presents a new wheel-leg mobile robot that combines the legs for changeable support polygon and mecanum wheels for holonomic motion. The robot has a human-like slim shape with 4 wheel-leg mechanisms, each of which has one 2-DOF leg frame and one mecanum wheel. To allow 2-DOF leg motion while maintaining the orientation of the mecanum wheels, a unique parallel link mechanism was devised. In order to achieve agile motion and impact and vibration absorption capability, a back-drivable high payload compound planetary gear was developed. The ground reaction force (GRF) compensation mechanism in each leg reduces the required payload of the actuators. The letter describes the detailed mechanical design of the robot and the actuators. The effectiveness of the proposed robot was verified in various experiments, fast omnidirectional motion test, a climbing test of a single step, and a motion test in the elevator with people.

robotics
Self-calibration of a differential wheeled robot using only a gyroscope and a distance sensor

Carlos Garcia-Saura

DOI: https://doi.org/10.48550/arXiv.1509.02154

2015-09-08

Abstract:Research in mobile robotics often demands platforms that have an adequate balance between cost and reliability. In the case of terrestrial robots, one of the available options is the GNBot, an open-hardware project intended for the evaluation of swarm search strategies. The lack of basic odometry sensors such as wheel encoders had so far difficulted the implementation of an accurate high-level controller in this platform. Thus, the aim of this thesis is to improve motion control in the GNBot by incorporating a gyroscope whilst maintaining the requisite of no wheel encoders. Among the problems that have been tackled are: accurate in-place rotations, minimal drift during linear motions, and arc-performing functionality. Additionally, the resulting controller is calibrated autonomously by using both the gyroscope module and the infrared rangefinder on board each robot, greatly simplifying the calibration of large swarms. The report first explains the design decisions that were made in order to implement the self-calibration routine, and then evaluates the performance of the new motion controller by means of off-line video tracking. The motion accuracy of the new controller is also compared with the previously existing solution in an odor search experiment.

Robotics
Design, Modeling, and Control of Norma: a Slider & Pendulum-Driven Spherical Robot

Saeed Moazami,M-Mahdi Naddaf-Sh,Srinivas Palanki,Hassan Zargarzadeh

DOI: https://doi.org/10.48550/arXiv.1908.02243

2020-02-20

Abstract:This paper discusses the design, modeling, and control of Norma, a novel 2 DOF mobile spherical robot (SR). The propelling mechanism of this robot consists of two actuators: a slider, and a rotational pendulum located on the SR's diagonal shaft. The slider can translate along the shaft and shift the robot's center of gravity towards the robot's sides. The pendulum rotates around the shaft to propel the SR to roll forward and backward. These two actuators enable the SR to perform both rolling and turning maneuvers as a nonholonomic robot. The advantage of the proposed mechanical design lies in its convenience of physical implementation, agility, and accurate mathematical model. The Euler Lagrange approach is utilized to derive the dynamics of the proposed mechanical structure using minimum simplifications possible. Further, a path tracking control scheme is introduced for a smooth trajectory. Finally, simulations are carried out in MATLAB to verify the accuracy of the mathematical model and the effectiveness of the controller against experimental results.

Robotics
Kinematics Calibration and Validation Approach Using Indoor Positioning System for an Omnidirectional Mobile Robot

Alexandru-Tudor Popovici,Constantin-Catalin Dosoftei,Cristina Budaciu

DOI: https://doi.org/10.3390/s22228590

2022-11-08

Abstract:Monitoring and tracking issues related to autonomous mobile robots are currently intensively debated in order to ensure a more fluent functionality in supply chain management. The interest arises from both theoretical and practical concerns about providing accurate information about the current and past position of systems involved in the logistics chain, based on specialized sensors and Global Positioning System (GPS). The localization demands are more challenging as the need to monitor the autonomous robot's ongoing activities is more stringent indoors and benefit from accurate motion response, which requires calibration. This practical research study proposes an extended calibration approach for improving Omnidirectional Mobile Robot (OMR) motion response in the context of mechanical build imperfections (misalignment). A precise indoor positioning system is required to obtain accurate data for calculating the calibration parameters and validating the implementation response. An ultrasound-based commercial solution was considered for tracking the OMR, but the practical observed errors of the readily available position solutions requires special processing of the raw acquired measurements. The approach uses a multilateration technique based on the point-to-point distances measured between the mobile ultrasound beacon and a current subset of fixed (reference) beacons, in order to obtain an improved position estimation characterized by a confidence coefficient. Therefore, the proposed method managed to reduce the motion error by up to seven-times. Reference trajectories were generated, and robot motion response accuracy was evaluated using a Robot Operating System (ROS) node developed in Matlab-Simulink that was wireless interconnected with the other ROS nodes hosted on the robot navigation controller.
Development and Control of a Real Spherical Robot

Karla Schröder,Gonzalo Garcia,Roberto Chacón,Guelis Montenegro,Alberto Marroquín,Gonzalo Farias,Sebastián Dormido-Canto,Ernesto Fabregas

DOI: https://doi.org/10.3390/s23083895

2023-04-11

Abstract:This paper presents the design and implementation of a spherical robot with an internal mechanism based on a pendulum. The design is based on significant improvements made, including an electronics upgrade, to a previous robot prototype developed in our laboratory. Such modifications do not significantly impact its corresponding simulation model previously developed in CoppeliaSim, so it can be used with minor modifications. The robot is incorporated into a real test platform designed and built for this purpose. As part of the incorporation of the robot into the platform, software codes are made to detect its position and orientation, using the system SwisTrack, to control its position and speed. This implementation allows successful testing of control algorithms previously developed by the authors for other robots such as Villela, the Integral Proportional Controller, and Reinforcement Learning.
Mechatronic design and development of a non-holonomic omnidirectional mobile robot for automation of primary production

Mostafa Sharifi,Matthew Samuel Young,XiaoQi Chen,Don Clucas,Christopher Pretty

DOI: https://doi.org/10.1080/23311916.2016.1250431

2016-10-27

Cogent Engineering

Abstract:This paper presents the mechatronic system design and development of a four-wheel drive/steer (4WD4S) mobile robot as a non-holonomic omnidirectional robot, MARIO—Mobile Autonomous Robot for Intelligent Operations. An innovative integrated application of CAD/CAM/CAE and RP has been employed for rapid development of the robot chassis and other mechanical parts by using different software tools. Most of the parts were designed by 3D CAD software which allows further CAE analysis including structural and motion analysis. To reduce the manufacturing time and cost, CAM and RP have been used to manufacture the main parts. These master parts are manufactured by workshop machining and 3D printing. Robot Operating System (ROS) alongside Gazebo simulator have been utilized for modelling, simulation, software development and visualization which enabled to develop the optimum embedded system to control the robot. With this integrated approach, a prototype of MARIO has been developed with a reasonably low manufacturing cost and time.
D A Novel Miniature Attitude Measurement System For Climbing And Walking Robots

Guanglong Wang,Chunxi Zhang,Zhaoying Zhou,Rong Zhu

DOI: https://doi.org/10.1142/9789812770189_0087

2007-01-01

Abstract:A novel design of miniature attitude measurement system for climbing and walking robots is presented. By integrating three-dimensional magnetometers and three microelectromechanical accelerometers, the system provides high-frequency position and attitude data. And it takes advantages of the solid-state configuration, small size, light weight, high reliability, low power consumption, rapid startup and relatively low cost. It can be used to test the transient attitude of the moving body such as robots. The three-axis accelerometers detect the three orthogonal components of the gravity, by which tilt of the robots including pitch and roll can be derived. Otherwise a three-axis magnetometer which are also assembled as an orthogonal placement to measure the three components of the Earth's magnetic field. The calculation and simulations indicate that the formalism proposed in this paper is able to reach an excellent long-term performance. Even if there is various error sources existing in the measurement, the non-orthogonal assembling error is the most dominating. We analyze the representative features of this error, establish a mathematic model for it, and successfully compensate this error via arithmetic. Finally, real experiments performed with a mobile robot are presented and analyzed. The results of the test indicate that the system can measure the freewill attitude in three-dimensional space. It is expected that this system will be adopted in many fields.
Design of Outdoor Autonomous Moble Robot

I-Hsi Kao,Jian-An Su,Jau-Woei Perng

DOI: https://doi.org/10.48550/arXiv.2201.12605

2022-01-29

Abstract:This study presents the design of a six-wheeled outdoor autonomous mobile robot. The main design goal of our robot is to increase its adaptability and flexibility when moving outdoors. This six-wheeled robot platform was equipped with some sensors, such as a global positioning system (GPS), high definition (HD) webcam, light detection and ranging (LiDAR), and rotary encoders. A personal mobile computer and 86Duino ONE microcontroller were used as the algorithm computing platform. In terms of control, the lateral offset and head angle offset of the robot were calculated using a differential GPS or a camera to detect structured and unstructured road boundaries. The lateral offset and head angle offset were fed to a fuzzy controller. The control input was designed by Q-learning of the differential speed between the left and right wheels. This made the robot track a reference route so that it could stay in its own lane. 2D LiDAR was also used to measure the relative distance from the front obstacle. The robot would immediately stop to avoid a collision when the distance between the robot and obstacle was less than a specific safety distance. A custom-designed rocker arm gave the robot the ability to climb a low step. Body balance could be maintained by controlling the angle of the rocker arm when the robot changed its pose. The autonomous mobile robot has been used for delivery service on our campus road by integrating the above system functionality.

Robotics,Systems and Control
Validation of 3-Space Wireless Inertial Measurement Units Using an Industrial Robot

Jaime Hislop,Mats Isaksson,John McCormick,Chris Hensman

DOI: https://doi.org/10.3390/s21206858

IF: 3.9

2021-10-15

Sensors

Abstract:Inertial Measurement Units (IMUs) are beneficial for motion tracking as, in contrast to most optical motion capture systems, IMU systems do not require a dedicated lab. However, IMUs are affected by electromagnetic noise and may exhibit drift over time; it is therefore common practice to compare their performance to another system of high accuracy before use. The 3-Space IMUs have only been validated in two previous studies with limited testing protocols. This study utilized an IRB 2600 industrial robot to evaluate the performance of the IMUs for the three sensor fusion methods provided in the 3-Space software. Testing consisted of programmed motion sequences including 360° rotations and linear translations of 800 mm in opposite directions for each axis at three different velocities, as well as static trials. The magnetometer was disabled to assess the accuracy of the IMUs in an environment containing electromagnetic noise. The Root-Mean-Square Error (RMSE) of the sensor orientation ranged between 0.2° and 12.5° across trials; average drift was 0.4°. The performance of the three filters was determined to be comparable. This study demonstrates that the 3-Space sensors may be utilized in an environment containing metal or electromagnetic noise with a RMSE below 10° in most cases.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation

Recent Researches on Emetine and its Value as a Therapeutic Agent in Amoebiasis and other Diseases.

Modeling and Control of Differential-Drive Chassis for a Homecare Assistive Robot

Development of a Human-Robot Hybrid Intelligent System Based on Brain Teleoperation and Deep Learning SLAM

Systematic Odometry Error Evaluation and Correction in a Human-Sized Three-Wheeled Omnidirectional Mobile Robot Using Flower-Shaped Calibration Trajectories

Adaptive heading correction for an industrial heavy-duty omnidirectional robot

Kinematic and optimal design of a three-wheeled holonomic omnidirectional robot platform for mobile manipulation tasks

The Assistant Personal Robot Project: From the APR-01 to the APR-02 Mobile Robot Prototypes

Design, Assembly and Control of a Differential/Omnidirectional Mobile Robot through Additive Manufacturing

The Otbot project: Dynamic modelling, parameter identification, and motion control of an omnidirectional tire-wheeled robot

Assistant Personal Robot (APR): Conception and Application of a Tele-Operated Assisted Living Robot

Design and Implementation of a Position, Speed and Orientation Fuzzy Controller Using a Motion Capture System to Operate a Wheelchair Prototype

A Multi-Terrain Robot Prototype With Archimedean Screw Actuators: Design, Realization, Modeling, and Control

Development of an Agile Omnidirectional Mobile Robot With GRF Compensated Wheel-leg Mechanisms for Human Environments

Self-calibration of a differential wheeled robot using only a gyroscope and a distance sensor

Design, Modeling, and Control of Norma: a Slider & Pendulum-Driven Spherical Robot

Kinematics Calibration and Validation Approach Using Indoor Positioning System for an Omnidirectional Mobile Robot

Development and Control of a Real Spherical Robot

Mechatronic design and development of a non-holonomic omnidirectional mobile robot for automation of primary production

D A Novel Miniature Attitude Measurement System For Climbing And Walking Robots

Design of Outdoor Autonomous Moble Robot

Validation of 3-Space Wireless Inertial Measurement Units Using an Industrial Robot