Abstract:The German research wind farm WiValdi was taken into service in 2023 and enables researchers and industry to conduct full-scale experiments. It currently consists of two highly instrumented wind turbines and multiple wind measurement masts. In one of the six wind turbine rotor blades, four Fiber Optic Strain Sensors (FOSS) are installed [1]. The strain which a wind turbine rotor blade exhibits under load is a key factor in the design, the certification and the assessment of its remaining service life as well as its further development and optimization. The aerodynamic optimization of wind turbine rotor blades leads to longer, and increasingly slender rotor blades and therefore increasingly relevant static and dynamic structural mechanical challenges. Usually the strain of wind turbine rotor blades during static deflection tests is measured with electrical strain gauges (SGs) or Fiber-Bragg-Gratings (FBGs). In the present study, quasi-continuous Fiber-Optic-Strain-Sensors (FOSS) are used in parallel with FBGs. The underlying technology is called optical frequency domain reflectometry (OFDR) and since only glass-fibers are used, it is inherently lightning protected [2]. Besides that, it is commercially available and delivers strain results at a spatial resolution of 2.6 mm. For this study, there are four 50-meter-long glass fibers bonded to the wind turbine rotor blade on suction and pressure side of each main spar of a 57 m rotor blade. This contribution shows how the FOSS measurements are post-processed and validated. The validated data is then used to obtain the relation between strain and introduced force over the length of each FOSS. With the accurate prediction of root-bending-moments, one of many possible use-cases of the FOSS results, is presented. Besides the computational model updating of the corresponding Finite-Element model in future investigations, the results will also be used to judge the current structural mechanical state of the wind turbine rotor blade at recurring service inspections. In that, results of the then to be acquired state at a given time and the shown base-line state will be compared. This will lead to high resolution insight into the deterioration of the structural integrity of the wind turbine rotor blade over time. Considering that standard telecommunication glass fibers can be used as sensors, the cost per sensor (i.e. fiber) is relatively low (circa 1500 € for 50 m). Despite the high cost of the required measurement system, the low prices of the fibers make FOSS measurements not only a scientifically interesting but also a potentially economically viable solution for measuring strain on wind turbine rotor blades.

Vibration monitoring of a helicopter blade model using the optical fiber distributed strain sensing technique

Structural Health Monitoring of Wind Turbine Blade Using Fiber Bragg Grating Sensors and Fiber Optic Rotary Joint

Dynamic Strain Measurement of Rotor Blades in Helicopter Flight Using Fiber Bragg Grating Sensor

FBG sensor based dynamic monitoring and analysis on sliding construction of a Prestressed Reticulated Shell-String structure

Flight demonstration of aircraft wing monitoring using optical fiber distributed sensing system

An Optoelectronic System For The In-Flight Measurement Of Helicopter Rotor Blades Motions And Strains

On the use of optical fiber Bragg grating (FBG) sensor technology for strain modal analysis

Development of a FBG based distributed strain sensor system for wind turbine structural health monitoring

Dynamic Fiber Bragg Grating Sensing Method

Carbon Cantilever Beam Health Inspection Using a Polymer Fiber Bragg Grating Array

Real-Time Virtual Sensing for Dynamic Vibration of Flexible Structure via Fiber Bragg Grating Sensors

Real-time Monitoring System for Multi-Mw Scale Wind Blades Using FBG Sensors

Health Monitoring of Engine Blades by Using an In-Line Fiber-Optic F-P Strain Sensor Based on Hollow-Core Photonic Crystal Fiber

Static Testing Using OFDR-based Quasi Continuous Fiber Optic Strain Sensing on the WiValdi Wind Turbine Rotor Blade

Experimental study based on fiber Bragg grating for measuring frequencies of turbine blade

Measuring Frequencies Of The Turbine Blade Based On Fiber Bragg Grating

Noise Cancellation of Helicopter Blade Deformations Measurement by Fiber Bragg Gratings

Dynamic Sensing Performance of a Point-Wise Fiber Bragg Grating Displacement Measurement System Integrated in an Active Structural Control System

Experimental Research of Helicopter Blade Load in Flight Based on Optical Sensing

In-flight health monitoring of a subscale wing using a fiber Bragg grating sensor system

Distributed Vibration Sensing with Time-Resolved Optical Frequency-Domain Reflectometry.