Abstract:Pancreatin pellets, placebo pellets and tablets containing vitamin B2 were coated with various aqueous and organic enteric polymers, HPMCAS, HP, Eudragit L 100-55, Eudragit L 30 D-55, CAP, CAT, CMEC and PVAP, comparatively investigated and tested for storage stability. With the exception of Eudragit L 100-55 and Eudragit L 30 D-55, higher amounts of coating material were needed to achieve gastro-resistance with aqueous coating than with organic coating. Film formation from aqueous dispersions of micronized HP 55 was affected by the degree of micronization and was improved by reducing the particle size of the polymer. Undercoating was another suitable measure to decrease the amount of coating material required. The choice of plasticizer was of special importance in the aqueous dispersions, and type and quantity must be appropriate for the polymer applied. Non-polymeric plasticizers such as triethyl citrate (TEC) evaporated along with water during the spraying or drying process and high temperatures promoted such losses. The moisture-sensitive pancreatic enzymes were damaged both by humidity and heat during aqueous coating. The extent of damage was dependent on the coating equipment used. Upon storage, coatings obtained from aqueous dispersions showed changes in enteric performance or release characteristics as a consequence of three chemical/physical mechanisms: hydrolysis of ester linkages in the polymer or plasticizer, evaporation of the plasticizer, delayed film formation. The active ingredient pancreatin induced hydrolysis of the ester based film-former hydroxypropyl methylcellulose acetate succinate (HPMCAS). However, even without the influence of enzymes, the phthalic ester groups of aqueous hydroxypropyl methylcellulose phthalate (HP) were partly cleaved after 11 months storage. In HPMCAS-coated pancreatin pellets, the plasticizer glyceryl triacetate was almost completely hydrolyzed by the enzymes, whilst triethyl citrate was lost by evaporation through permeable packaging material at elevated temperatures. Open storage at elevated temperatures and humidities caused changes in the surface structure of HPMCAS coatings, consisting of a smoothing of the originally somewhat porous film and sticking. When applied to vitamin B2 tablets, Eudragit L 100-55, Opadry enteric (PVAP) and Aqoat (HPMCAS) proved to be quite stable aqueous enteric coatings, whereas cellulose acetate phthalate CAP or cellulose acetate trimellitate CAT coatings as ammonia-neutralized aqueous solution or as water-based pseudolatex Aquateric were unstable when stored under stress conditions.

Formulation of paracetamol-containing pastilles with in situ coating technology

Delayed Sustained Drug Release from Electrostatic Powder Coated Tablets with Ultrafine Polymer Blends

Preparation of Sustained Release Capsules by Electrostatic Dry Powder Coating, Using Traditional Dip Coating As Reference

Co-Spray Drying of Paracetamol and Propyphenazone with Polymeric Binders for Enabling Compaction and Stability Improvement in a Combination Tablet

In-situ fast gelling formulation for oral sustained drug delivery of paracetamol to dysphagic patients

Wurster Technology-Assisted Step-by-Step Engineering of Multi-layered Pellets (Sprinkles): Microscopy, Micro-CT, and e-Tongue-Based Analysis

Towards a Better Understanding of the Post-Gastric Behavior of Enteric-Coated Formulations

Effect of processing methods on xylitol-starch base co-processed adjuvant for orally disintegrating tablet application

Going green: Development of a sustainable lipid-based enteric coating formulation for low-dose aspirin multiparticulate systems

Application of a novel electrostatic dry powder coating technology on capsules for enteric release

Extrusion 3D Printing of Paracetamol Tablets from a Single Formulation with Tunable Release Profiles Through Control of Tablet Geometry

Taste-Masked Pellets of Warfarin Sodium: Formulation towards the Dose Personalisation

3D Printing of Paracetamol Suppositories: An Automated Manufacturing Technique for Individualized Therapy

Preparation and in vitro evaluation of hot-melt extruded pectin-based pellets containing ketoprofen for colon targeting

Exploring Immersion Coating as a Cost-Effective Method for Small-Scale Production of Enteric-Coated Gelatin Capsules

Paracetamol extended release FDM 3D printlets: Evaluation of formulation variables on printability and drug release

Comparative Direct Compression Property of a Novel Pregelatinized Starch in Paracetamol Tablets

CHARACTERIZATION OF PARACETAMOL ORALLY DISINTEGRATING TABLET USING GELATIN 1% AND 2% AS BINDER AND POLYPLASDONE XL-10 10% AS DISINTEGRANT (Prepared by Freeze Drying Method)

Influence of aqueous coatings on the stability of enteric coated pellets and tablets

Preparation and Evaluation of Hot-Melt Extruded Patient-Centric Ketoprofen Mini-Tablets