Abstract:Journal of Composite Materials, Ahead of Print. Detecting the low-velocity impact damage on the FRP composite structures can be challenging because the visible signs on the surface may be subtle. Mitigating the effects of BVID (Barely Visible Impact Damage) is crucial in ensuring the safety and reliability of composite components, especially in industries where these materials are commonly used, such as aerospace and automotive. This article explores the experimental investigations of the impact and post-impact damage propagation under compression in the Graphene Nano-Platelets (GNPs) infused glass fiber epoxy composite laminates. A comparative study of varying the percentage of the nano-platelets (0, 0.25, 0.5, and 0.75%) in the matrix material of the composite laminate is presented. The impact tests at low energies (15 J, 20 J, and 25 J), followed by the quasi-static compression tests, are carried out as per the procedures mentioned in the ASTM D7136/D7137. The digital image correlation technique (DIC) is used to measure strains and plot the strain field on the impacted face of the specimen under compression. Damage envelopes of the impact and compression tests are studied using X-ray CT scans. Micro-level failures are observed through Scanning Electron Microscopy (SEM) to get better insights into the failure mechanism of the composite materials under impact and compression loadings. Upon completing the study, it is found that the addition of the GNP into the matrix materials not only increased the impact performance but also increased the load-carrying capacity of the laminate under compressive loading. A decrement of 2–21% in the energy absorbed in the damage formation is seen with the incorporation of GNPs into composite materials. A maximum increment of 17% in the compressive strength is observed for the composite laminates with the 0.75% GNPs. However, for a particular percentage of the GNP, the compressive strength of the laminate is reduced with an increase in impact energy compared with its virgin counterpart. From X-ray CT scans, it is seen that the laminate under the compression tests fails due to excessive ply-splitting and the delamination at the damage site created during the impact. Fiber breakage, fiber brooming, matrix cracking, fiber-matrix debonding, etc., are some of the other failure modes observed in SEM studies.

Mechanical and quasi-static puncture behavior of hybrid glass/Kevlar/carbon fiber laminate composites with graphene nanoparticles

Mechanical Characterization of Graphene-Hexagonal Boron Nitride-Based Kevlar-Carbon Hybrid Fabric Nanocomposites

Effect of graphene nano-platelets on mechanical and impact characteristics of carbon/Kevlar reinforced epoxy hybrid nanocomposites

Synergetic effect of incorporating graphene, CNT and hybrid nanoparticles on the mechanical properties of glass fiber reinforced epoxy laminated composites

Influence of hybrid nano/micro particles on the mechanical performance of cross-ply carbon fibre fabric reinforced epoxy polymer composite materials

Investigation of graphene nanoplatelets-deposited textured metal matrix composite plates for improved mechanical properties: a numerical approach

Improvement of mechanical performance via interfacial strengthening of carbon fiber‐epoxy reinforced hybrid laminate by incorporation of functionalized graphene nanoplatelet interphase

Exploring the synergistic effects of graphene on the mechanical and vibrational response of kenaf/pineapple fiber‐reinforced hybrid composites

Experimental analysis of tensile strength of 6-layer carbon/kevlar/epoxy hybrid composite reinforced with nano-graphene/silica nanoparticles

Mechanical properties of a carbon fiber reinforced epoxy resin composite improved by integrating multi-walled carbon nanotubes and graphene nanoplatelets

Mechanical properties of a laminated composite of aramid fabric and high‐density polyethylene films reinforced with calcium carbonate, montmorillonite, and graphene

Mechanical Performance of Hybrid Graphene Nanoplates, Fly-Ash, Cement, Silica, and Sand Particles Filled Cross-Ply Carbon Fibre Woven Fabric Reinforced Epoxy Polymer Composites Beam and Column

Fabrication and Experimental Estimation of Mechanical Properties of Kevlar-Glass/Epoxy Interwoven Composite Laminate

Sustainable mechanical properties evaluation for graphene reinforced Epoxy/Kevlar fiber using MD simulations

Enhanced damage tolerance and fracture toughness of lightweight carbon-Kevlar fiber hybrid laminate

Enhancement of the contact behavior of a quasi-isotropic carbon fiber/epoxy matrix laminate with an elastic body by modifying the fiber-matrix interphase using graphene nanoplatelets

Effect of graphene nano-platelets on the low-velocity-impact and compression-after-impact strength of the glass fiber epoxy composite laminates

Development of Improved Flexural and Impact Performance of Kevlar/Carbon/Glass Fibers Reinforced Polymer Hybrid Composites

Influence of graphene nanoplatelet concentration on the electrical, mechanical, and piezoresistive properties of glass fiber/epoxy composites

Influence of Graphene Nano Fillers and Carbon Nano Tubes on the Mechanical and Thermal Properties of Hollow Glass Microsphere Epoxy Composites

Thermal and Quasi-Static Mechanical Characterization of Polyamide 6-Graphene Nanoplatelets Composites