Abstract:Statement of problem: Multiple factors can influence the accuracy of intraoral scanners (IOSs). However, the impact of scan extension and starting quadrant on the accuracy of IOSs for fabricating tooth-supported crowns remains uncertain. Purpose: The purpose of the present in vitro study was to measure the influence of scan extension (half or complete arch scan) and the starting quadrant (same quadrant or contralateral quadrant of the location of the crown preparation) on the accuracy of four IOSs. Material and methods: A typodont with a crown preparation on the left first molar was digitized (T710) to obtain a reference scan. Four scanner groups were created: TRIOS 5, PrimeScan, i700, and iTero. Then, 3 subgroups were defined based on the scan extension and starting quadrant: half arch (HA subgroup), complete arch scan starting on the left quadrant (CA-same subgroup), and complete arch scan starting on the right quadrant (CA-contralateral subgroup), (n=15). The reference scan was used as a control to measure the root mean square (RMS) error discrepancies with each experimental scan on the tooth preparation, margin of the tooth preparation, and adjacent tooth areas. Two-way ANOVA and pairwise multiple comparisons were used to analyze trueness (α=.05). The Levene and pairwise comparisons using the Wilcoxon Rank sum tests were used to analyze precision (α=.05). Results: For the tooth preparation analysis, significant trueness and precision differences were found among the groups (P<.001) and subgroups (P<.001), with a significant interaction group×subgroup (P=.002). The iTero and TRIOS5 groups obtained better trueness than the PrimeScan and i700 groups (P<.001). Moreover, half arch scans obtained the best trueness, while the CA-contralateral scans obtained the worst trueness (P<.001). The iTero group showed the worst precision among the IOSs tested. For the margin of the tooth preparation evaluation, significant trueness and precision differences were found among the groups (P<.001) and subgroups (P<.001), with a significant interaction group×subgroup (P=.005). The iTero group obtained best trueness (P<.001), but the worst precision (P<.001) among the IOSs tested. Half arch scans obtained the best trueness and precision values. For the adjacent tooth analysis, trueness and precision differences were found among the groups (P<.001) and subgroups tested (P<.001), with a significant interaction group×subgroup (P=.005). The TRIOS 5 obtained the best trueness and precision. Half arch scans obtained the best accuracy. Conclusions: Scan extension and the starting quadrant impacted the scanning trueness and precision of the IOSs tested. Additionally, the IOSs showed varying scanning discrepancies depending on the scanning area assessed. Half arch scans presented the highest trueness and precision, and the complete arch scans in which the scan started in the contralateral quadrant of where the crown preparation was obtained the worst trueness and precision.

3D intraoral scanning techniques support the effects of crown morphology on dental caries

Influence of scan extension and starting quadrant on the accuracy of four intraoral scanners for fabricating tooth-supported crowns

Research progress on early caries detection with optical coherence tomography

Factors Influencing the Accuracy of Intraoral Impression in Implant Restoration

[Research and development of clinical application accuracy of intraoral three-dimensional scanning technology].

Investigation on the Effectiveness of Digital Scanning Combined with Reverse Engineering Technology in Demonstrating Full Crown Tooth Preparation

Occlusal caries detection and monitoring using a 3D intraoral scanner system. An in vivo assessment

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

[Influence of Intraoral Scan and Dental Cast Scan on Occlusal Quantitative Analysis of Virtual Dental Model].

Influence of Scanner Precision and Analysis Software in Quantifying Three-Dimensional Intraoral Changes: Two-Factor Factorial Experimental Design

Three-dimensional analysis of coronal root canal morphology of 136 permanent mandibular first molars by micro-computed tomography

Influence of intraoral scanning coverage on the accuracy of digital implant impressions – An in vitro study

Design of Wear Facets of Mandibular First Molar Crowns by Using Patient-Specific Motion with an Intraoral Scanner: A Clinical Study.

A comparative study of the application of three digital imaging techniques to assess the thickness of the palatal mucosa of the maxillary anterior teeth

Performance of the caries diagnosis feature of intraoral scanners and near-infrared imaging technology-A narrative review

Volumetric analysis after caries excavation with caries detecting dyes and chemomechanical caries removal agents using 3D scanner-a randomised clinical trial

Assessment of the coronal root canal morphology of permanent maxillary first molars using digital 3D-reconstruction technology based on micro-computed tomography data

Evaluation of the Quality of Three-Dimensional Data Acquired by Using Two Kinds of Structure Light Intra-Oral Scanner to Scan the Crown Preparation Model

Do intraoral scanning technologies affect the trueness of dental arches with crowding, diastema, and edentulous spaces? A clinical perspective

Computer-assisted methods for obtaining quantitative parameters of tooth preparation for crown

Antimicrobial, remineralization, and infiltration: advanced strategies for interrupting dental caries