Expectations vs performance.

G. Cohen

Abstract:

What problem does this paper attempt to address?

The effect of cryogenic thermal cycling on aging, rejuvenation, and mechanical properties of metallic glasses

Nikolai V. Priezjev

DOI: https://doi.org/10.1016/j.jnoncrysol.2018.09.041

2018-08-20

Abstract:The structural relaxation, potential energy states, and mechanical properties of a model glass subjected to thermal cycling are investigated using molecular dynamics simulations. We study a non-additive binary mixture which is annealed with different cooling rates from the liquid phase to a low temperature well below the glass transition. The thermal treatment is applied by repeatedly heating and cooling the system at constant pressure, thus temporarily inducing internal stresses upon thermal expansion. We find that poorly annealed glasses are relocated to progressively lower levels of potential energy over consecutive cycles, whereas well annealed glasses can be rejuvenated at sufficiently large amplitudes of thermal cycling. Moreover, the lowest levels of potential energy after one hundred cycles are detected at a certain temperature amplitude for all cooling rates. The structural transition to different energy states is accompanied by collective nonaffine displacements of atoms that are organized into clusters, whose typical size becomes larger with increasing cooling rate or temperature amplitude. We show that the elastic modulus and the peak value of the stress overshoot exhibit distinct maxima at the cycling amplitude, which corresponds to the minimum of the potential energy. The simulation results indicate that the yielding peak as a function of the cycling amplitude for quickly annealed glasses represents a lower bound for the maximum stress in glasses prepared with lower cooling rates.

Soft Condensed Matter,Materials Science
Mechanical Property and Structural Changes by Thermal Cycling in Phase-Separated Metallic Glasses

Y. Tang,H. B. Xiao,X. D. Wang,Q. P. Cao,D. X. Zhang,J. Z. Jiang

DOI: https://doi.org/10.1016/j.jmst.2020.10.050

2021-01-01

Abstract:Nondestructive cryogenically thermal cycling has been a simple but effective treatment to enhance mechanical properties of glassy materials.However,how the structural heterogeneities on nanometer scales are affected by thermal cycling is still an issue.Here,we report the response of spatial heterogeneities in three selected Ti 41 Zr 25 Be 28 Fe 6 ,Zr 56 Co 14 Cu 14 Al 16 and Zr 42 Y 14 Co 22 Al 22 （at.%） metallic glasses（MGs） with different compositions to the thermal cycling,which show significantly different structure and properties after the same treatments and could be ascribed to the joint contribution of relaxation and rejuvenation induced by thermal cycling.The rejuvenation is initially prevailed in a Zr-Y-containing MG,whereas the relaxation is dominant in a Cu-Co-containing MG,both eventually entering into a dynamic equilibrium state.By employing nanometer-scale structural models,the intrinsic correlation between the spatial heterogeneity and thermal cycling is proposed.The discovery could provide the fundamental understanding of the role of spatial heterogeneity in influencing the macroscopic properties of MGs via thermal cycling and help design high-performance glassy materials by tailoring their atomic structures with suitable thermal treatments.
Anelastic-like nature of the rejuvenation of metallic glasses by cryogenic thermal cycling

Miguel B. Costa,Juan J. Londoño,Andreas Blatter,Avinash Hariharan,Annett Gebert,Michael A. Carpenter,A. Lindsay Greer

DOI: https://doi.org/10.1016/j.actamat.2022.118551

IF: 9.4

2022-11-26

Acta Materialia

Abstract:Cryogenic thermal cycling (CTC) is an effective treatment for improving the room-temperature plasticity and toughness in metallic glasses. Despite considerable attention to characterizing the effects of CTC, they remain poorly understood. A prominent example is that, contrary to expectation, the stored energy in a metallic glass first rises, and then decreases, as CTC progresses. In this work, CTC is applied to bulk metallic glasses based on Pd, Pt, Ti, or Zr. The effects on calorimetric and mechanical properties are evaluated. Critically, CTC-induced effects, at whatever stage, are found to decay over about one week at room temperature after CTC, returning the properties to those of the as-cast glass. A model is proposed for CTC-induced effects, treating them as analogous to the accumulation of anelastic strain. The implications for analysis of existing data, and for future research on CTC effects, are highlighted.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Tunable rejuvenation behavior of a metallic glass by residual stress modulation

X.B. Qiu,X.L. Bian,D. Şopu,Y.X. Gao,J. Yi,Y.D. Jia,G. Wang

DOI: https://doi.org/10.1016/j.jmrt.2023.09.172

IF: 6.267

2023-09-22

Journal of Materials Research and Technology

Abstract:In this study, the structure changes and related mechanical properties of the Zr 61 Ti 2 Cu 25 Al 12 metallic glass treated by triaxial compression and followed by further cryogenic thermal cycling were systematically studied. It is found that the structure evolution based on the changes in the relaxation enthalpy and diffraction peak position shows inconsistencies with each other. Vickers hardness mapping reveals that residual stresses may impart and store in the extremely deformed metallic glass sample, which can be verified from the change of hardness and that can well explain such inconsistencies. As thermal cycling proceeds, the stored residual stresses will relieve and compete with structure softening from the process of thermal cycling, leading to a tunable rejuvenation behavior. A plausible model that correlates rejuvenation and thermal-mechanical protocols is proposed. This work highlights that residual stress plays a vital role in the metallic glass rejuvenation and should be taken into account, which may be helpful for the design of metallic glasses with desired mechanical performance.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Atomistic modelling of thermal-cycling rejuvenation in metallic glasses

Baoshuang Shang,Weihua Wang,Alan Lindsay Greer,Pengfei Guan

DOI: https://doi.org/10.1016/j.actamat.2021.116952

IF: 9.4

2021-07-01

Acta Materialia

Abstract:<p>Cycling of a metallic glass between ambient and cryogenic temperatures can induce higher-energy states characteristic of glass formation on faster cooling. This rejuvenation, unexpected because it occurs at small macroscopic strains and well below the temperatures of thermally induced structural change, is important, for example, in improving plasticity. Molecular-dynamics simulations elucidate the mechanisms by which thermal cycling can induce relaxation (reaching lower energy) as well as rejuvenation. Thermal cycling, over tens of cycles, drives local atomic rearrangements progressively erasing the initial glass structure. This arises mainly from the heating stage in each thermal cycle, linked to the intrinsic structural heterogeneity in metallic glasses. Although, in particular, the timescales in MD simulations are shorter than in physical experiments, the present simulations reproduce many physically observed effects, suggesting that they may be useful in optimizing thermal cycling for tuning the properties of metallic glasses and glasses in general.</p>

materials science, multidisciplinary,metallurgy & metallurgical engineering
Nanoscale Structural Evolution and Anomalous Mechanical Response of Nanoglasses by Cryogenic Thermal Cycling

Wei-Hong Liu,B A Sun,Herbert Gleiter,Si Lan,Yang Tong,Xun-Li Wang,Horst Hahn,Yong Yang,Ji-Jung Kai,C T Liu

DOI: https://doi.org/10.1021/acs.nanolett.8b01007

2018-07-11

Abstract:One of the central themes in the amorphous materials research is to understand the nanoscale structural responses to mechanical and thermal agitations, the decoding of which is expected to provide new insights into the complex amorphous structural-property relationship. For common metallic glasses, their inherent atomic structural inhomogeneities can be rejuvenated and amplified by cryogenic thermal cycling, thus can be decoded from their responses to mechanical and thermal agitations. Here, we reported an anomalous mechanical response of a new kind of metallic glass (nanoglass) with nanoscale interface structures to cryogenic thermal cycling. As compared to those metallic glasses by liquid quenching, the Sc75Fe25 (at. %) nanoglass exhibits a decrease in the Young's modulus but a significant increase in the yield strength after cryogenic cycling treatments. The abnormal mechanical property change can be attributed to the complex atomic rearrangements at the short- and medium- range orders due to the intrinsic nonuniformity of the nanoglass architecture. The present work gives a new route for designing high-performance metallic glassy materials by manipulating their atomic structures and helps for understanding the complex atomic structure-property relationship in amorphous materials.
Structural and Dynamical Changes in a Gd-Co Metallic Glass by Cryogenic Rejuvenation

Shinya Hosokawa,Jens R. Stellhorn,Laszlo Pusztai,Yoshikatsu Yamazaki,Jing Jiang,Hidemi Kato,Tetsu Ichitsubo,Eisuke Magome,Nils Blanc,Nathalie Boudet,Koji Ohara,Satoshi Tsutsui,Hiroshi Uchiyama,Alfred Q. R. Baron

2023-11-08

Abstract:To experimentally clarify the changes in structural and dynamic heterogeneities in a metallic glass (MG), Gd65Co35, by rejuvenation with a temperature cycling (cryogenic rejuvenation), high-energy x-ray diffraction (HEXRD), anomalous x-ray scattering (AXS), and inelastic x-ray scattering (IXS) experiments were carried out. By a repeated temperature change between liquid N2 and room temperatures 40 times, tiny but clear structural changes are observed by HEXRD even in the first neighboring range. Partial structural information obtained by AXS reveals that slight movements of the Gd and Co atoms occur in the first- and second-neighboring shells around the central Gd atom. The concentration inhomogeneity in the nm size drastically increases for the Gd atoms by the temperature cycling, while the other heterogeneities are negligible. A distinct change was detected in a microscopic elastic property by IXS: The width of longitudinal acoustic excitation broadens by about 20%, indicating an increase of the elastic heterogeneity of this MG by the thermal treatments. These static and dynamic results explicitly clarify the features of the cryogenic rejuvenation effect experimentally.

Materials Science,Disordered Systems and Neural Networks
Relaxation and Strain-Hardening Relationships in Highly Rejuvenated Metallic Glasses

Xudong Yuan,Daniel Şopu,Kaikai Song,Jürgen Eckert

DOI: https://doi.org/10.3390/ma15051702

2022-02-24

Abstract:One way to rejuvenate metallic glasses is to increase their free volume. Here, by randomly removing atoms from the glass matrix, free volume is homogeneously generated in metallic glasses, and glassy states with different degrees of rejuvenation are designed and further mechanically tested. We find that the free volume in the rejuvenated glasses can be annihilated under tensile or compressive deformation that consequently leads to structural relaxation and strain-hardening. Additionally, the deformation mechanism of highly rejuvenated metallic glasses during the uniaxial loading-unloading tensile tests is investigated, in order to provide a systematic understanding of the relaxation and strain-hardening relationship. The observed strain-hardening in the highly rejuvenated metallic glasses corresponds to stress-driven structural and residual stress relaxation during cycling deformation. Nevertheless, the rejuvenated metallic glasses relax to a more stable state but could not recover their initial as-cast state.
Thermal cycling-induced evolution of structure and local mechanical properties in metallic glass

Shuhan Zhang,Xinzhe Wang,Jennifer Hay,Udo D. Schwarz,Amit Datye

DOI: https://doi.org/10.1016/j.jallcom.2024.174709

IF: 6.2

2024-05-05

Journal of Alloys and Compounds

Abstract:The influence of thermal treatment on the long-term mechanical properties of two different kinds of metallic glasses was investigated in this study. As model systems, bulk metallic glasses (BMGs) with the composition of Pd 43 Cu 27 Ni 10 P 20 cycled 60, 200, and 500 times between 77 K and room temperature and Zr 44 Ti 11 Cu 10 Ni 10 Be 25 cycled 300, 500, and 700 times have been employed. To ensure that meaningful steady-state properties have been reached, experiments have been performed three years after sample preparation. It was found that the thermal cycling of the Pd-based BMGs had induced rejuvenation when compared to the non-cycled sample, including a higher relaxation enthalpy, lower modulus, hardness, activation volume, and shear transformation zone volume. However, for Zr-BMGs, a rejuvenation to relaxation behavior is observed. Also, while Zr-BMGs showed significantly changes in yielding behavior upon thermal cycling, fluctuations in Pd-BMGs were negligible. We speculate that the observed substantial differences between these two samples might originate because Pd-BMG has a denser structure and higher fragility, making it more difficult to induce excess free volumes.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Structure-dynamics relationships in cryogenically deformed bulk metallic glass

Florian Spieckermann,Daniel Şopu,Viktor Soprunyuk,Michael B. Kerber,Jozef Bednarčík,Alexander Schökel,Amir Rezvan,Sergey Ketov,Baran Sarac,Erhard Schafler,Jürgen Eckert

DOI: https://doi.org/10.1038/s41467-021-27661-2

2022-01-11

Abstract:The atomistic mechanisms occurring during the processes of aging and rejuvenation in glassy materials involve very small structural rearrangements that are extremely difficult to capture experimentally. Here we use in-situ X-ray diffraction to investigate the structural rearrangements during annealing from 77 K up to the crystallization temperature in Cu44Zr44Al8Hf2Co2 bulk metallic glass rejuvenated by high pressure torsion performed at cryogenic temperatures and at room temperature. Using a measure of the configurational entropy calculated from the X-ray pair correlation function, the structural footprint of the deformation-induced rejuvenation in bulk metallic glass is revealed. With synchrotron radiation, temperature and time resolutions comparable to calorimetric experiments are possible. This opens hitherto unavailable experimental possibilities allowing to unambiguously correlate changes in atomic configuration and structure to calorimetrically observed signals and can attribute those to changes of the dynamic and vibrational relaxations ({\alpha}-, {\beta}- and {\gamma}-transition) in glassy materials. The results suggest that the structural footprint of the {\beta}-transition is related to entropic relaxation with characteristics of a first-order transition. Dynamic mechanical analysis data shows that in the range of the {\beta}-transition, non-reversible structural rearrangements are preferentially activated. The low-temperature {\gamma}-transition is mostly triggering reversible deformations and shows a change of slope in the entropic footprint suggesting second-order characteristics.

Materials Science
An order of magnitude enhancement in ductility of a metallic glass of peak rejuvenation

Jiaojiao Yi,Yihao Wang,Lisha Liu,Yibin Zhu,Gongji Yang,Mingqin Xu,Honghao Ge,Lingti Kong,Chunguang Tang

DOI: https://doi.org/10.1016/j.jmrt.2023.12.016

IF: 6.267

2023-12-07

Journal of Materials Research and Technology

Abstract:Exceptional ductility has been a long-sought-after property of metallic glasses, and cryogenic thermal cycling rejuvenation has been actively explored to enhance the plasticity of metallic glasses. By tuning the holding time and number of cycles of cryogenic thermal cycling processing, we here report a (Zr 0.8125 Cu 0.1875 ) 79 Ni 10 Al 10 Nb 1 metallic glass of peak rejuvenation with the plasticity of an order of magnitude higher than that of the as-cast glass, without sacrificing its strength. Characterizations indicate that the loose atomic packing of the metallic glass of peak rejuvenation facilitates the generation and proliferation of shear bands in the early stage of plastic deformation, and the resultant dense shear bands tend to be deflected due to their interaction with each other and/or structural inhomogeneity in the matrix, hindering their rapid propagation and in turn increasing the plasticity. The combination of high relaxation enthalpy and high plasticity obtained here is outstanding from the previous rejuvenated metallic glasses which have either high relaxation enthalpy or high plasticity, while never both. This work identifies an alloy system with very high efficiency in plasticity improvement through cryogenic thermal cycling rejuvenation and represents a promising guide for improving the plasticity of metallic glasses.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Rejuvenation engineering in metallic glasses by complementary stress and structure modulation

Daniel Şopu,Florian Spieckermann,Xilei Bian,Simon Fellner,Jonathan Wright,Megan Cordill,Christoph Gammer,Gang Wang,Mihai Stoica,Jürgen Eckert

DOI: https://doi.org/10.1038/s41427-023-00509-5

IF: 10.761

2023-11-24

NPG Asia Materials

Abstract:Abstract Residual stress engineering is widely used in the design of new advanced lightweight materials. For metallic glasses, attention has been given to structural changes and rejuvenation processes. High-energy scanning X-ray diffraction strain mapping reveals large elastic fluctuations in notched metallic glasses after deformation under triaxial compression. Microindentation hardness mapping hints at a competing hardening–softening mechanism after compression and reveals the complementary effects of stress and structure modulation. Transmission electron microscopy proves that structure modulation and elastic heterogeneity distribution under room temperature deformation are related to shear band formation. Molecular dynamics simulations provide an atomistic understanding of the confined deformation mechanism in notched metallic glasses and the related fluctuations in the elastic and plastic strains. Thus, future focus should be given to stress modulation and elastic heterogeneity, which, together with structure modulation, may allow the design of metallic glasses with enhanced ductility and strain-hardening ability.

materials science, multidisciplinary
Cryogenic thermal cycling rejuvenation in metallic glasses: Structural and mechanical assessment

Nicolás Amigo

DOI: https://doi.org/10.1016/j.jnoncrysol.2022.121850

2022-11-15

Abstract:Rejuvenation in metallic glasses (MGs) can be achieved by means of thermal cycling treatments at cryogenic temperatures. Here, atomic scale studies were carried out to explore thermal cycling in CuZr MGs at different species contents. Enhanced ductility was observed due to several factors. All samples presented higher potential energy and less-dense structures upon treatments, indicating rejuvenated states. Furthermore, populations of high-centrosymmetric Voronoi polyhedra decreased, while liquid-like structures increased, which are usually related to low rigidity. Atomic connectivity was explored as a measure of the medium range order, revealing that thermal cycling reduced the fraction of 3-atom connections, while increased 2-atom and 4-atom connections. Since 3-atom connections are associated to more-ordered structures, its weakening explains the enhanced plasticity achieved by MGs upon thermal cycling treatments. This study provides new insights into rejuvenation of MGs, delivering atomic scale descriptions at both the short range and medium range order.

materials science, multidisciplinary, ceramics
Deformation behavior of thermally rejuvenated Zr-Cu-Al-(Ti) bulk metallic glass

Nandita Ghodki,Shristy Jha,Siva Shankar Alla,Yu-Chia Yang,George M. Pharr,Sundeep Mukherjee

DOI: https://doi.org/10.1038/s41598-024-71658-y

IF: 4.6

2024-09-11

Scientific Reports

Abstract:The deformation behavior of metallic glasses has been shown in prior studies to be often dependent on its structural state, namely higher energy "rejuvenated" state versus lower energy "relaxed" state. Here, the deformation behavior of thermally rejuvenated Zr-Cu-Al-(Ti) bulk metallic glasses (BMGs) was evaluated. Rejuvenation was achieved by cryogenic thermal cycling with increase of free volume measured in terms of enthalpy of relaxation. Hardness, stiffness, and yield strength of the BMGs were all found to decrease while plasticity increased after rejuvenation. More free volume in the rejuvenated BMG resulted in homogeneous plastic deformation as was evident from the high strain rate sensitivity and more pronounced shear band multiplication during uniaxial compression. Shear transformation zone (STZ) volume was calculated by cooperative shear model and correlated well with the change in structural state after rejuvenation. The enhanced plasticity with the addition of 1 at. % Ti as well as after cryogenic thermal cycling was explained by lower activation energy for shear flow initiation due to increased heterogeneity induced in the system. Molecular dynamics simulation demonstrated that the variation in plastic deformation behavior is correlated with local atomic structure changes.

multidisciplinary sciences
Various Rejuvenation Behaviors of Zr-Based Metallic Glass by Cryogenic Cycling Treatment with Different Casting Temperatures

Wei Guo,Rui Yamada,Junji Saida,Shulin Lü,Shusen Wu

DOI: https://doi.org/10.1186/s11671-018-2816-7

2018-12-01

Nanoscale Research Letters

Abstract:The rejuvenation behavior of an Zr50Cu40Al10 (at.%) metallic glass upon cryogenic cycling treatment has been investigated. At a high casting temperature, the microstructure of the glass is quite homogenous and thus, internal stress cannot be generated during cycling. Therefore, the glass cannot be rejuvenated by cryogenic cycling treatment. In the contrary, by lowering the casting temperature, nano-sized heterogeneity can be induced and subsequently generates the internal stress and rejuvenates the glass. Once the glass is rejuvenated, the more induced free volume can plasticize the glass with a higher plastic strain. These findings point out that the synthesis conditions can tailor the heterogeneity of the glass and subsequently affect the following rejuvenation behavior upon thermal treatment. It can also help understand the mechanisms of rejuvenation of metallic glass upon cryogenic cycling treatment.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Tailoring mechanical heterogeneity, nanoscale creep deformation and optical properties of nanostructured Zr-based metallic glass

Jing-Xian Cui,Qiang Luo,Zheng-Guo Zhang,Jing-Tao Zhu,Bao-Long Shen

DOI: https://doi.org/10.1007/s12598-023-02440-8

IF: 6.318

2023-09-06

Rare Metals

Abstract:Metallic glasses are spatially heterogeneous at the nanometer scale. However, the effects of external excitation on their structural and mechanical heterogeneity and the correlation to their properties are still unresolved. Nanoindentation, atomic force microscopy (AFM) and high-resolution transmission electron microscopy (HRTEM) were carried out to explore the effects of cryogenic thermal cycling (CTC) on mechanical/structural heterogeneity, nanoscale creep deformation and optical properties of nanostructured metallic glass thin films (MGTFs). The results indicate that CTC treatment alters the distribution fluctuations of hardness/modulus and energy dissipation and results in an increase-then-decrease variation in mechanical heterogeneity. By applying Maxwell–Voigt model, it can be shown that CTC treatment results in a remarkable activation of more defects with longer relaxation time in soft regions but has only a slight effect on defects in hard regions. In addition, CTC treatment increases the transition time from primary-state stage to steady-state stage during creep deformation. The enhanced optical reflectivity of the MGTFs after 15 thermal cycles can be attributed to increased aggregation of Cu and Ni elements. The results of this study shed new light on understanding mechanical/structural heterogeneity and its influence on nanoscale creep deformation and optical characteristics of nanostructured MGTFs, and facilitate the design of high-performance nanostructured MGTFs.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Intermediate Structural State for Maximizing the Rejuvenation Effect in Metallic Glass Via Thermo-Cycling Treatment

S. J. Kang,Q. P. Cao,J. Liu,Y. Tang,X. D. Wang,D. X. Zhang,I. S. Ahn,A. Caron,J. Z. Jiang

DOI: https://doi.org/10.1016/j.jallcom.2019.05.026

IF: 6.2

2019-01-01

Journal of Alloys and Compounds

Abstract:Annealing of metallic glasses (MGs) at temperature near glass transition temperature (Tg) triggers relaxation and often hampers their performances in service. Rejuvenation treatment of MGs by thermal cycling is recently intensively investigated. However, the mechanism responsible for the structural rejuvenation still remains elusive. In this work, we present a systematic study on the rejuvenation effect of a Zr46Cu38Al8Ag8 MG annealed at 0.9Tg for various durations, subjected to thermo-cycling treatment. It is found that well relaxed samples after long-term annealing are almost unaffected, while short-term annealed samples exhibit large rejuvenation effect by thermo-cycling treatment. Using synchrotron X-ray diffraction, we find that thermal cycling results in a disordering at the short-range scale, where the rejuvenation effect is large in a heterogeneous sample. More interestingly, the thermo-cycling treatment on intermediate structure with 20 h-annealed sample relatively exhibits a high degree rejuvenation effect, as compared to shorter- and longer-term annealed samples. This finding indicates that the activation barrier for rejuvenation strongly depends on the original structural states, e.g., free volume, inherent stress and structural heterogeneity.
Rejuvenation of a deformed metallic glass dominated by immature shear band zones during cryogenic thermal cycling

Sailong Zhang,Jingyu Zhou,Jing Geng,Yifan Yang,Peipeng Jin,Bo Shi

DOI: https://doi.org/10.1103/physrevb.109.104205

2024-03-19

Physical Review B - Condensed Matter and Materials Physics

Abstract:Cryogenic thermal cycling (CTC) treatment is a promising technique to rejuvenate metallic glasses (MGs), but whose effect is usually highly dependent on the original structure. Spanning shear bands and nonspanning shear bands in deformed MGs not only have different structures, but also are situated in different strain fields, so their responses to CTC are expected to be different. In the present work, the structure, energy state, and property evolutions of the spanning and nonspanning shear bands in deformed MGs during the CTC process were investigated by experiments and molecular dynamics simulations. It was found that CTC increased the proportion of atoms with inelastic strain and induced a rejuvenation in the immature shear band zones that nevertheless led a relaxation in the mature shear band zones. This work not only deepens the understanding of the rejuvenation mechanism of deformed MGs, but also provides a unique perspective for improving their mechanical properties. https://doi.org/10.1103/PhysRevB.109.104205 ©2024 American Physical Society
Enthalpy of anelasticity and rejuvenation of metallic glasses

Miguel B. Costa,A. Lindsay Greer

DOI: https://doi.org/10.1016/j.actamat.2023.119609

IF: 9.4

2024-02-01

Acta Materialia

Abstract:Elastostatic loading and cryogenic thermal cycling are known to be capable of increasing the enthalpy of metallic glasses and improving their mechanical properties, effects of particular interest as these treatments operate in the nominally elastic regime. The increases in volume and stored energy induced by these treatments are studied for two prototypical (Pd- and Zr-based) bulk metallic glasses. The energy increase induced by elastostatic loading is associated with unrecovered anelastic strain, and not with viscoplastic strain as previously proposed. This energy increase decays similarly to that induced by thermal cycling, implying a storage mechanism that is similar for these two treatments and distinct from that operating under plastic deformation. For different as-cast and annealed states of metallic glasses, increased energy shows a linear correlation with increased volume. Property changes induced by elastostatic loading and thermal cycling also show a linear correlation, but with a different gradient, indicating greater excess volume for a given energy. It is proposed that the changes induced by treatments within the elastic limit do not constitute ‘rejuvenation’ of a metallic glass, but rather structural excitation localized at shear-transformation zones. The energetics of such excitation are analysed.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Achieving structural rejuvenation in metallic glass by modulating β relaxation intensity via easy-to-operate mechanical cycling

L.T. Zhang,Y.J. Wang,E. Pineda,Y. Yang,J.C. Qiao

DOI: https://doi.org/10.1016/j.ijplas.2022.103402

IF: 8.5

2022-10-01

International Journal of Plasticity

Abstract:Structural rejuvenation is an effective measure to optimize the mechanical properties of metallic glasses (MGs). Sophisticated solutions to rejuvenation include thermal cycling, laser shocking, and multiaxial stress loading. Here, we propose an easy-to-operate mechanical cycling as an alternative strategy to tailor the mechanical relaxation, deformation, and structural heterogeneity of MGs. Structural rejuvenation in a La-based MG is achieved via mechanical cycling even at very few cycles (102 tension load cycles) and low frequencies (10−3 Hz). The results manifest intuitively the competition between structural relaxation and rejuvenation, which constitutes the structural evolution in MGs. A theoretical model is constructed which reveals a scenario that mechanical cycling wakes up frozen flow defect, accelerating creep and, thus, enhancing the β relaxation in MGs. Therefore, this handy anti-ageing methodology provides an alternative pathway to optimize the mechanical properties of MGs. It also contributes to a more comprehensive understanding of the structure-property relationship in amorphous materials, especially with regard to the correlation between structural rejuvenation and relaxation behavior in such topologically disordered materials.

materials science, multidisciplinary,engineering, mechanical,mechanics

Expectations vs performance.

The effect of cryogenic thermal cycling on aging, rejuvenation, and mechanical properties of metallic glasses

Mechanical Property and Structural Changes by Thermal Cycling in Phase-Separated Metallic Glasses

Anelastic-like nature of the rejuvenation of metallic glasses by cryogenic thermal cycling

Tunable rejuvenation behavior of a metallic glass by residual stress modulation

Atomistic modelling of thermal-cycling rejuvenation in metallic glasses

Nanoscale Structural Evolution and Anomalous Mechanical Response of Nanoglasses by Cryogenic Thermal Cycling

Structural and Dynamical Changes in a Gd-Co Metallic Glass by Cryogenic Rejuvenation

Relaxation and Strain-Hardening Relationships in Highly Rejuvenated Metallic Glasses

Thermal cycling-induced evolution of structure and local mechanical properties in metallic glass

Structure-dynamics relationships in cryogenically deformed bulk metallic glass

An order of magnitude enhancement in ductility of a metallic glass of peak rejuvenation

Rejuvenation engineering in metallic glasses by complementary stress and structure modulation

Cryogenic thermal cycling rejuvenation in metallic glasses: Structural and mechanical assessment

Deformation behavior of thermally rejuvenated Zr-Cu-Al-(Ti) bulk metallic glass

Various Rejuvenation Behaviors of Zr-Based Metallic Glass by Cryogenic Cycling Treatment with Different Casting Temperatures

Tailoring mechanical heterogeneity, nanoscale creep deformation and optical properties of nanostructured Zr-based metallic glass

Intermediate Structural State for Maximizing the Rejuvenation Effect in Metallic Glass Via Thermo-Cycling Treatment

Rejuvenation of a deformed metallic glass dominated by immature shear band zones during cryogenic thermal cycling

Enthalpy of anelasticity and rejuvenation of metallic glasses

Achieving structural rejuvenation in metallic glass by modulating β relaxation intensity via easy-to-operate mechanical cycling