Abstract:Biomedical sciences facilitated fast detection methods for many diseases recently. The development of this field has led to the dynamic development of Lab-On-a-Chip devices which are portable, require small sample size and have low cost. Fluid manipulation in such bioanalytical systems is a key issue. One of the key features of these devices is the sample preparation which includes the dilution and complete mixing of the analyte with reagents of adequate buffer solution. The mixing possibilities are limited on microscale, since turbulent flow cannot occur due to the dominant viscosity. Chaotic advection can be considered as an ideal mixing method in microfluidic channels as the flows are laminar. The herring-bone like ridges on the channel of the herring-bone type micromixers (Figure 1) act as anisotropic fluid resistance generating secondary transversal flow. The Laminar Flow interface of COMSOL Multiphysics® software was used to solve the velocity field of the micromixer to characterize fluid flow properties. For modelling the mixing phenomena two approaches were used. Mixing by diffusion along the channel was modeled with Transport of Diluted Species interface. To avoid numerical diffusion and high computational cost we used the Particle Tracing module to observe mixing at the level of particles. To optimize the mixing efficiency we conducted a parametric sweep on the thickness of the ridges. Secondary flow and the rotation caused by the herring-bone structure were well observable in the velocity field (Figure 2). The concentration distribution calculated by COMSOL Multiphysics® showed that a high concentration fluid layer was rotated into a low concentration region resulting more surface area for mixing by diffusion. Poincaré map of particle trajectories (Figure 3) showed the layered structure of particle distribution which was similar to the baker's transformation. Modeled herring-bone structures were fabricated in polydimethylsiloxane (PDMS) using multilayer technology. The SU-8 epoxy-based photoresist was applied as molding replica. An improved 3D multilayer formation from SU-8 was developed so that microfluidic systems with high aspect ratio sidewalls and advanced functional parts could be fabricated well. Dye was used for the measurement of mixing by diffusion and yeast cells were used for the particle approach. Pictures were recorded in inverted microscope with bright field imaging. The scattered light from the yeast cells provided good signal (Figure 4). The measurements confirmed the rotation caused by the ridges and also the layered flow characteristics. COMSOL Multiphysics® was used in this study to simulate mixing by diffusion and by secondary flow. Particle tracing model was applied to simulate the mixing of cells in the microchannel. Results agreed well with the measurement, an optimal herring-bone structure was proposed for integration into a bioanalytical system.

Analyzing Mixing Inhomogeneity in a Microfluidic Device by Microscale Schlieren Technique

A Novel Passive Micromixer with Modified Asymmetric Lateral Wall Structures

Numerical Simulation of the Efficiency of Mixing in Heterogeneous Microchannels with Patterned Surface Potentials

Numerical Simulation on Fluid Mixing by Effects of Geometry in Staggered Oriented Ridges Micromixers

An Investigation of Flow Patterns and Mixing Characteristics in a Cross-Shaped Micromixer within the Laminar Regime

In-line Raman imaging of mixing by herringbone grooves in microfluidic channels

Millisecond Mixing of Two Liquid Streams in a Mixer Model

Study on the mixing of fluid in curved microchannels with heterogeneous surface potentials

Method for determining mixing index in microfluidics by RGB color model

Sensitivity analysis and study of the mixing uniformity of a microfluidic mixer

Numerical Simulation of the Scalar Mixing Characteristics in Three-dimensional Microchannels

Optimization of the Herringbone Type Micromixer Using Numerical Modelling and Validation By Measurements

On the Quantification of Mixing in Microfluidics

Consistent Evaluation Methods for Microfluidic Mixers

Numerical analysis of a microfluidic mixer and the effects of different cross-sections and various input angles on its mixing performance

Mixing in microfluidic devices and enhancement methods

Analysis of Sequential Micromixing Driven by Sinusoidally Shaped Induced-Charge Electroosmotic Flow

Passive and Active Mixing in Microfluidic Devices

Visualization of Micro-Scale Mixing in Miscible Liquids Using Μ-Lif Technique and Drug Nano-Particle Preparation in T-shaped Micro-Channels

Numerical simulation on Taylor dispersion enabled micromixture