Abstract:The X-structure has been used for vibration isolation due to its nonlinear characteristic. Here, the use of an inerter-based X-structure vibration isolator is proposed to improve the dynamic performance of the traditional X-structure vibration isolator by exploiting the mass amplification characteristic of the inerter while satisfying the lightweight design requirement. Based on the arrangement of the inerter and X-structure, transverse-mounted, series-connected and parallel-connected inerter-based X-structure vibration isolators are designed. The relevant dynamic equations for these isolators are established using the Lagrange principle, their dynamic responses are obtained using the harmonic balance method and pseudoarc-length method, and their isolation performances are evaluated by three performance indices and compared with those of the X-structure and traditional linear vibration isolators. The results show that the transverse-mounted inerter-based X-structure vibration isolator has nonlinear inertial, nonlinear conservative forcing and nonlinear stiffness characteristics and that the series-connected and parallel-connected inerter-based X-structure vibration isolators have linear inertial and nonlinear stiffness characteristics. The transverse-mounted and parallel-connected inerter-based X-structure vibration isolators have a smaller relative dynamic displacement peak, absolute dynamic displacement peak, absolute displacement transmissibility peak and resonance frequency and wider isolation frequency band than the X-structure isolator, and only the high-frequency absolute displacement transmissibility is larger for the transverse-mounted and parallel-connected inerter-based X-structure vibration isolators. A series-connected inerter-based X-structure vibration isolator can isolate a relatively low-frequency vibration because of the antiresonance frequency and thus can improve the high-frequency absolute displacement transmissibility, while the relative dynamic displacement peak, absolute dynamic displacement peak and absolute displacement transmissibility peak are larger for the series-connected inerter-based X-structure vibration isolator than for the X-structure isolator. The parallel-connected inerter-based X-structure vibration isolator exhibits the best isolation performance and the transverse-mounted inerter-based X-structure vibration isolator exhibits the best shock performance among the four X-structure and linear vibration isolators studied. In addition, the experimental prototype of the inerter-based X-structure vibration isolator is built to test its performance, the theoretical and experimental results are compared to verify the validity of the theoretical modelling. This paper verifies the benefit of introducing the inerter in the X-structure and offers a better choice for effective vibration isolation in practical engineering.

Vibration characteristics of multi-dimensional isolator based on 4-PUU parallel mechanism with joint clearance

Vibration characteristics and isolation in vibration-sensitive areas under moving vehicle load

On the Analysis of A Piecewise Nonlinear-Linear Vibration Isolator with High-Static-Low-Dynamic-Stiffness under Base Excitation

Comparison of the Dynamic Performance of Nonlinear One and Two Degree-Of-Freedom Vibration Isolators with Quasi-Zero Stiffness

BASIC THEORY AND TECHNOLOGY IN THE ACTIVE VIBRATION ISOLATION OF PRECISION DEVICES

Response and Performance of A Nonlinear Vibration Isolator with High-Static-Low-Dynamic-Stiffness under Shock Excitations

Design and Analysis of a Vibration Isolator with Adjustable High Static–Low Dynamic Stiffness

The Design and Analysis of a Novel Passive Quasi-Zero Stiffness Vibration Isolator

Active/passive vibration isolation with multi-axis transmission control: Analysis and experiment

A multi-directional vibration isolator based on Quasi-Zero-Stiffness structure and time-delayed active control

Analysis and Experimental Study on Dynamic Characteristics of an Integrated Quasi-Zero Stiffness Isolator

Design of a novel two-degree-of-freedom translational-rotation low-frequency vibration isolation platform

A 6-DOF micro-vibration isolation platform based on the quasi-zero-stiffness isolator

Modeling and Analysis of a Four-Parameter Vibration Isolator with Frequency-dependent Damping and Its Implementation based on GERF

Design and Tests for a New Type Nonlinear Low-Frequency Passive Vibration Isolation System

Vibration Isolation Platform for Large-Amplitude-low-frequency Excitation by Parallel-Stack-assembly Design of Miura Origamis

The Bond Graph Modeling and Experimental Verification of a Hydraulic Inertial Vibration Isolator Including Nonlinear Effects

Design and modeling of a quasi-zero stiffness isolator for different loads

Design and experimental study of a two-stage nonlinear vibration isolators with quasi-zero stiffness

An inerter-based X-structure vibration isolator

Dynamic Analysis and Decoupling Control of Octo-Pneumatic Actuator Vibration Isolation Platform