Abstract:Background: This in vitro study was performed to determine the appropriate power output setting for an erbium, chromium-doped:yttrium, scandium, gallium, and garnet (Er,Cr:YSGG) laser used in periodontal pocket irradiation by examining the morphologic alterations of the root surfaces and the efficiency of calculus removal. Methods: Sixty-five non-carious extracted human teeth were used in this study. For morphologic analysis of the root surface, the clean, single roots of 22 teeth were separated into 91 pieces, and these pieces were immersed in acrylic resin. The specimens with root-surface exposure were prepared and divided randomly into three groups: a control group (N=8), an irradiation without water group (no water [NW] group; N=39), and an irradiation in water to simulate the conditions in a periodontal pocket group (in water [IW] group; N=44). The power output settings for laser irradiation were 0.5, 1.0, 1.5, and 2.0 W for each group. The roughness (Ra), depth (Z), and width (X) of the disk specimens were determined after laser irradiation. Eight other single-rooted teeth were examined by scanning electron microscopy (SEM) after laser irradiation under the same conditions. Thirty-five single- or multirooted teeth with heavy subgingival calculus were used to test the efficiency of laser scaling. The efficiency of calculus removal was quantified by measuring the time needed to remove the calculus completely using the laser. Results: The mean Ra and Z values in the IW group were significantly higher than in the NW group with the same power output. In addition, these values with 0.5- and 1.0-W power output settings were significantly lower than with 1.5- and 2.0-W settings in the NW and IW groups. No obvious morphologic differences could be found between the 0.5- and 1.0-W power output specimens under SEM. Additionally, thermal alterations, i.e., carbonization or melting, were completely absent in the IW group. Regarding the efficiency of calculus removal, the 0.5-W setting (0.11+/-0.036 mm2/second) was significantly inferior to the 1.0-W setting (0.27+/-0.043 mm2/second). However, there was no significant difference between 1.0- and 1.5-W (0.36+/-0.11 mm2/second). The 2.0-W setting (0.63+/-0.272 mm2/second) was much more efficient but resulted in significant morphologic alterations. Conclusions: Based on these findings, it is appropriate to use a 1.0-W power output setting with an Er,Cr:YSGG laser for root scaling. This may be done without any conspicuous morphologic alterations to the root surface and with acceptably efficient removal of calculus.

Assessment of root surfaces of apicected teeth: a scanning electron microscopy evaluation

Topography of root-end surface after freehand and three-dimensional-guided apicoectomy procedure: A scanning electron microscope study

Crack formation on resected root surfaces subjected to conventional, ultrasonic, and laser root-end cavity preparation

Comparison of the effect of hand instruments, an ultrasonic scaler, and an erbium-doped yttrium aluminium garnet laser on root surface roughness of teeth with periodontitis: a profilometer study

Evaluation of Dentinal Microcracks following Diode Laser- and Ultrasonic-Activated Removal of Bioceramic Material during Root Canal Retreatment

SEM Evaluation of Tooth Surface after a Composite Filling Removal Using Er:YAG Laser, Drills with and without Curettes, and Optional EDTA or NaOCl Conditioning

Effects of Er,Cr:YSGG Laser on the Root Surface of Periodontitis and Healthy Teeth

Effect of Different Nickel–Titanium Rotary Systems on Dentinal Crack Formation During Root Canal Preparation in Primary Molars: An in Vitro Study

Scanning electron microscopy evaluation of the root canal morphology after Er:YAG laser irradiation

Incidence of apical crack formation and propagation during removal of root canal filling materials with different engine driven nickel-titanium instruments

Oval Root Canals Prepared With Two Different Endodontic Rotary Files: An In Vitro Study Comparing the Incidence of Dental Defects

Scanning Electron Microscope Image Analysis of Bonding Surfaces following Removal of Composite Resin Restoration Using Er: YAG Laser: In Vitro Study

Root Canal Wall Dentin Structure in Uninstrumented but Cleaned Human Premolars: A Scanning Electron Microscopic Study

Laser applications in smear layer removal from posterior root canals: A comparative study

Micron-scale crack propagation in laser-irradiated enamel and dentine studied with nano-CT

Effects of Er,Cr:YSGG laser irradiation on the root surface: morphologic analysis and efficiency of calculus removal

Comparison of surface roughness of root cementum and orthodontically induced root resorption craters from high- and low-fluoridation areas: a 3D confocal microscopy study

Effect of Er: YAG or Nd:YAG Laser Exposure on Fluorosed and Non-Fluorosed Root Surfaces: An In Vitro Study

[Scanning Electron Microscopy Was Used to Observe Dentin Morphology in Primary and Permanent Teeth Treated by Erbium: Yttrium-Aluminum-garnet Laser].

Comparative evaluation of hand and rotary file systems on dentinal microcrack formation during pulpectomy procedure in primary teeth: an in vitro study

Scanning electron microscopy analysis of conventional and controlled-memory nickel titanium files before and after multi-uses in root canals