Abstract:This study was carried out to evaluate the effect of acid etching versus laser etching of dentin surface on the bonding of Composite and Compomer restorative materials to dentin surface by studying microleakage at the dentin-filling interface, compositional analysis of dentin surface, and Scanning Electron Microscopic (SEM) study of the bonding area. 120 freshly extracted premolar teeth were divided according to surface treatment into three groups. Group I (Acid etching group) contained thirty teeth. Twenty teeth were selected to assess microleakage by forming standardized class V cavity on the buccal surface of the selected teeth. Then, teeth were subdivided into two subgroups with 10 teeth in each. Subgroup (i) delivered composite filling while subgroup (ii) delivered compomer filling according to manufacturer instructions. microleakage at the dentin-filling interface of teeth was examined using dye penetration method. dye penetration scores at occlusal and gingival margins were recorded and tabulated. Five dentin surfaces of five teeth from group I were etched by acid then prepared for compositional analysis of dentin surface by Infra-Red (IR) Spectroscopy. Another Five dentin surfaces were etched by acid then prepared for (SEM) assessment. Group II (Laser etching group) contained ninety teeth, twenty teeth were used for assessing microleakage after laser etching taking similar steps to that of acid etching. Thirty dentin surfaces of thirty teeth were etched by laser with different parameters then prepared for compositional analysis of dentin surface by IR Spectroscopy. Thirty dentin surfaces of thirty teeth were etched by laser with different parameters then prepared for SEM assessment. Group III (Untreated group) contained ten teeth that were left untreated. Five dentin surfaces of five teeth were subjected to IR Spectroscopy assessment. Five dentin surfaces of five teeth were prepared for SEM assessment. The results revealed that acid etching of dentin surface resulted in significant less leakage compared to laser etching. IR Spectroscopy revealed changes in dentin surface structure indicating that there was a reaction occurred by the acid and laser etching. SEM assessment showed more openings of dentinal tubules in case of acid etching, while in case of laser etching, there were a surface structural changes with a melting and fusion dentin surface. Acid etching of dentin gives better results on the bonding of Composite and Compomer filling materials than laser etching and thus gives more successful clinical condition. Further investigations are needed by using different types of laser to get more benefit from applications of laser clinically.

Morphological Changes of Human Dentin after Erbium-Doped Yttrium Aluminum Garnet (Er:YAG) and Carbon Dioxide (CO2) Laser Irradiation and Acid-etch Technique: An Scanning Electron Microscopic (SEM) Evaluation

Enamel and Dentin Exposed to Pulsed Nd∶YAG Laser

Bond Strength Experiment of Human Dentin Following Pulsed Nd:YAG Laser

[Scanning Electron Microscopy Was Used to Observe Dentin Morphology in Primary and Permanent Teeth Treated by Erbium: Yttrium-Aluminum-garnet Laser].

Morphological analysis of cementum and root dentin after Er:YAG laser irradiation

Scanning Electron Microscope Image Analysis of Bonding Surfaces following Removal of Composite Resin Restoration Using Er: YAG Laser: In Vitro Study

Topographical Analysis of Human Enamel after Phosphoric Acid Etching and Er,Cr:YSGG Laser Irradiation

The Influence of Er:YAG Laser on the Dissolution Rate and Morphology of the Root Cement A scanning electron microscopic study

Comparative study of the effect of laser irradiation and acid etching surface treatment on bonding of some dental restorative materials To dentin surface

Effects of Erbium:Yttrium-Aluminum-Garnet Laser Irradiation on Bovine Dentin Contaminated by Cariogenic Bacteria.

Effect of Er∶YAG Laser Treatment on Dentin Surface and Bonding Strength

Ultrastructural Analysis of Er:YAG Lased Bovine Dentin Contaminated by Cariogenic Bacteria

Influence of Er∶ YAG Laser Treatment on Enamel Surface and Shear Bond Strength of Resin

SEM Evaluation of Tooth Surface after a Composite Filling Removal Using Er:YAG Laser, Drills with and without Curettes, and Optional EDTA or NaOCl Conditioning

Effect of erbium yttrium aluminium garnet laser dentin conditioning on dental pulp stem cells viability

Effect of Various Er:YAG Laser Conditioning Energies on Dentin Surface: Micromorphological Investigation and Dentin-Resin Shear Bond Strength Test.

Effects of Nd: YAG laser irradiation on the root canal wall dentin of human teeth: a SEM study

Effect of Er: YAG or Nd:YAG Laser Exposure on Fluorosed and Non-Fluorosed Root Surfaces: An In Vitro Study

Morphological Analysis of Irradiated Dentin by Scanning Electron Microscope under Anhydrous Condition

In vitro studies the influence of Nd: YAG laser on dental enamels

Effect of Laser Irradiance and Fluoride Varnish on Demineralization Around Dental Composite Restorations