Acoustic emissions during 3.1 MHz ultrasound bulk ablation in vitro.

T. D. Mast,V. Salgaonkar,Chandra Karunakaran,John A. Besse,Saurabh Datta,C. Holland

DOI: https://doi.org/10.1016/j.ultrasmedbio.2008.02.007

2008-09-01

Abstract:

What problem does this paper attempt to address?

Preparation and electrocatalytic dechlorination performance of Pd/Ti electrode

jingli zhang,zhanping cao,yongzhi chi,liping xie,ligang lin

DOI: https://doi.org/10.1080/19443994.2014.903205

IF: 1.1

2015-01-01

Desalination and Water Treatment

Abstract:The Pd/Ti working electrode was prepared by the electrochemical deposition on the Ti plate and its structure and morphology were analyzed by an X-ray diffraction (XRD) and a transmission electron microscopy. The results showed that Palladium (Pd) crystals were coated uniformly on Titanium (Ti) base material with the average size of 8.69 nm. The cyclic voltammetry was employed to study the electrochemical reduction characteristics of 2,4,5-tripolychlorinated biphenyl (PCB29) in an electrocatalytic system. The results showed that the PCB29 dechlorination was a two-electron transfer reduction controlled by adsorption and conformed to the characteristics of the first-order reaction. The efficiencies of PCB29 degradation in the electrocatalytic system were more than 95% after 5 h at its concentration (mg/L) of 60, 80, and 100. The dechlorinations of PCB29 obeyed the pseudo-first-order reaction kinetic behavior. The reaction rate constant was approximately 0.011 min(-1). The reaction rate increased slightly as the temperature rose. The 2,5-PCB was first mainly generated by PCB29 para-position dechlorination, 2-PCB by meta-position dechlorination, and then diphenyl by the subsequent ortho-position dechlorination. Diphenyl could be further hydrogenated to phenyl cyclohexane. The chlorine substitution position on PCB29 mainly affected the order of PCB29 electrocatalytic dechlorination.
Complete dechlorination of 2,4-dichlorophenol in aqueous solution on palladium/polymeric pyrrole-cetyl trimethyl ammonium bromide/foam-nickel composite electrode.

Zhirong Sun,Xuefeng Wei,Yanbo Han,Shan Tong,Xiang Hu

DOI: https://doi.org/10.1016/j.jhazmat.2012.11.017

IF: 13.6

2013-01-01

Journal of Hazardous Materials

Abstract:The electrochemically reductive dechlorination of 2,4-dichlorophenol (2,4-DCP) in aqueous solution on palladium/polymeric pyrrole-cetyl trimethyl ammonium bromide/foam-nickel electrode (Pd/PPy-CTAB/foam-Ni electrode) was investigated in this paper. Pd/PPy-CTAB/foam-Ni electrode was prepared and characterized by cyclic voltammetry (CV), scanning electron microscope (SEM), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) adsorption and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The influences of some experimental factors such as the dechlorination current, dechlorination time and the initial pH on the removal efficiency and the current efficiency of 2,4-DCP dechlorination on Pd/PPy-CTAB/foam-Ni electrode were studied. Complete removal of 2,4-DCP was achieved and the current efficiency of 47.4% could be obtained under the conditions of the initial pH of 2.2, the dechlorination current of 5 mA and the dechlorination time of 50 min when the initial 2,4-DCP concentration was 100 mg L(-1). The analysis of high performance liquid chromatography (HPLC) identified that the intermediate products were 2-chlorophenol (2-CP) and 4-chlorophenol (4-CP). The final products were mainly phenol. Its further reduction product cyclohexanone was also detected. The electrocatalytic dechlorination pathways of 2,4-DCP on Pd/PPy-CTAB/foam-Ni electrode were discussed. The stability of the electrode was favorable that it could keep dechlorination efficiency at 100% after having been reused 10 times. Results revealed that the stable prepared Pd/PPy-CTAB/foam-Ni electrode presented a good application prospect in dechlorination process with high effectiveness and low cost.
Electrochemical degradation of pentachlorophenol on a palladium modified gas-diffusion electrode.

H Wang,J L Wang

DOI: https://doi.org/10.2166/wst.2009.176

2009-01-01

Abstract:Pd/C catalyst was prepared by hydrogen reduction method and used for the Pd/C gas-diffusion electrode. It was characterized by cyclic voltammetry (CV) technique. The electrochemical degradation of pentachlorophenol (PCP) was investigated in a diaphragm electrolysis' device, feeding firstly with hydrogen gas then with air, using the Pd/C gas-diffusion electrode and the carbon/polytetrafluoroethylene (C/PTFE) gas-diffusion electrode as the cathode, respectively. The results indicated that the Pd/C gas-diffusion cathode can not only reductively dechlorinate PCP by feeding hydrogen gas, but also accelerate the two-electron reduction of O-2 to hydrogen peroxide (H2O2) by feeding air. Therefore, both the removal efficiency and the dechlorination degree of PCP exceeded 80% after 120 min, and the average removal efficiency of PCP in terms of total organic carbon (TOC) exceeds 75% after 200 min by using Pd/C gas-diffusion cathode, which was better than that of the C/PTFE gas-diffusion cathode. High-performance liquid chromatography (HPLC) allows identifying phenol as the dechlorination product.
Electrochemical Dechlorination of 3-chlorophenol with Palladium-Loaded Carbon Felt Electrode

Di Li,Siqi Zhang,Yingjia Chen,Haiming Yang,Xin Geng,Suying Zhao,Jiajun Li,Lixiang Li

DOI: https://doi.org/10.3390/coatings11101188

IF: 3.236

2021-09-29

Coatings

Abstract:Electrochemical dechlorination with Pd-loaded electrodes offers an effective method for detoxification of wastewater. Electro-reductive dechlorination of 3-chlorophenol (3-CP) with Pd loaded on carbon felt (Pd/CF) was investigated. Pd was loaded on carbon felt by electrolytic method. The prepared electrodes were characterized by XRD, SEM, EDS, S-TEM and CV. The sizes of the Pd particles loaded on CF were found in the range of 100–400 nm. The preparing conditions including loading amount of Pd and loading currents were investigated. Moreover, the reduction conditions including electrolytes, reductive currents and recycle times were also studied. The Pd/CF cathodes with Pd loading of 0.5 mg/cm2, preparing current of 5 mA, electrolyte concentration of 30 mmol/L NaCl and 30 mmol/L CH3COONa were used to reduce 3-CP for dechlorination. When CH3COONa was used as the electrolyte, the current was 5 mA, the initial pH was 7.5, the initial 3-CP concentration was 1 mmol/L and the degradation rate of 3-CP could reach 95.81% after reduction of 150 min under an argon atmosphere. The electrochemical reduction of 3-CP was confirmed to follow the first-order rate law. 3-CP was qualitatively dechlorinated to phenol on electrodes with Pd. The fact that active hydrogen formed on palladium during preliminary electrolysis could be proved by the dechlorinated 3-CP in non-electroreduction after preliminary electrolysis. A possible reduction pathway was proposed based on the results.

materials science, multidisciplinary,physics, applied, coatings & films
Bile salts increase epithelial cell proliferation through HuR-induced c-Myc expression.

E. Perrone,Lan Liu,D. Turner,E. Strauch

DOI: https://doi.org/10.1016/j.jss.2012.02.029

IF: 2.417

2012-11-01

Journal of Surgical Research

Abstract:
Electrochemical Dechlorination of 2,4-Dichlorophenol in Aqueous Solution on Palladium-Loaded Meshed Titanium Electrode.

Z. R. Sun,M. Gao,Y. Z. Peng,X. Hu

DOI: https://doi.org/10.2166/wst.2011.033

IF: 2.43

2011-01-01

Water Science & Technology

Abstract:Electrochemical dechlorination of 2,4-dichlorophenol (2,4-DCP) in aqueous solution was investigated on palladium-loaded meshed titanium (Pd/Ti) electrode at ambient temperature. Pd/Ti electrode was prepared with an electrodepositing method. Scanning Electron Microscope (SEM) micrographs show that Pd microparticles uniformly disperse on the meshed Ti supporting electrode with spheroidal structure. Dechlorination experimental results indicate that, in aqueous solution, with the current efficiency of 24.3%, the removal efficiency of 100 mg/L 2,4-DCP on Pd/Ti electrode was 93.2% under the conditions of the dechlorination current of 5 mA and dechlorination time of 90 min. The effect of initial 2,4-DCP concentration was also investigated.
Electrocatalytic Hydrodechlorination of 2,4,5-Trichlorobiphenyl on A Palladium-Modified Nickel Foam Cathode

Bo Yang,Gang Yu,Jun Huang

DOI: https://doi.org/10.1021/es071168o

IF: 11.4

2007-01-01

Environmental Science & Technology

Abstract:Palladium-modified materials have been found to be effective electrodes for the reductive degradation of chlorinated compounds in aqueous solution. This study investigated the electrocatalytic hydrodechlorination (ECH) of polychlorinated biphenyls (PCBs) in solvent/surfactant-aided solutions in a palladium-modified nickel foam electrode using a divided flow-through cell. The reaction pathways of 2,4,5-PCB hydrodechlorination were proposed due to the analysis of intermediates by GC/MS. The mechanism of electrocatalytic reaction on the Pd/Ni foam cathode was examined by studying the effect of surfactant type, sorption behavior of PCBs on the electrode, and current densities on the ECH efficiency of PCBs. The conversion of PCBs was controlled by the micelle structures of the surfactants instead of the charged species. According to the analysis of hydrogen transformation processes on the electrode surface, we propose that the ECH process was initiated by the transfer of highly active hydrogen atoms [H] from the prior polarized Pd particles to the less polarized Pd particles by spillover on the Pd/Ni foam cathode. Therefore, the total available surface was larger than the originally polarized surface, and [H] could smoothly react with PCBs that were adsorbed on the surface. As a result, a high ECH efficiency can be achieved with the Pd/Ni foam electrode.
Electrochemical degradation of sodium pentachlorophenol on a Pd/C gas-diffusion electrode

Hui Wang,Jian-Long Wang

DOI: https://doi.org/10.3321/j.issn:0250-3301.2009.02.048

2009-01-01

Abstract:Pd/C catalyst was prepared by hydrogen reduction method and used for the Pd/C gas-diffusion electrode. It was characterized by cyclic voltammetry (CV) techniques. The electrochemical degradation of sodium pentachlorophenol (PCP-Na) was investigated in a diaphragm electrolysis device, feeding firstly with hydrogen gas then with air, using the Pd/C gas-diffusion electrode and the carbon/polytetrafluoroethylene (C/PTFE) gas-diffusion electrode as the cathode, respectively. The results indicate that the two-electron reduction from O2 to hydrogen peroxide (H2O2) is produced at the Pd/C gas-diffusion electrode, and the accumulated H2O2 in the cathodic compartment reach to the steady concentration of 9.8 mg/L after 100 min. The Pd/C gas-diffusion cathode can reductively dechlorinate PCP-Na by feeding hydrogen gas, and accelerate the two-electron reduction of O2 to hydrogen peroxide (H2O2) by feeding air. Therefore, both the removal efficiency and the dechlorination degree of PCP-Na exceed 80% after 100 min, and the average removal efficiency of PCP-Na in terms of total organic carbon (TOC) exceeds 75% after 200 min by using Pd/C gas-diffusion cathode,which is better than that of the C/PTFE gas-diffusion cathode. High performance liquid chromatography (HPLC) allows identifying phenol as the dechlorination product.
Improvement of the conventional flat plate electrode: Application of filtered Pd@Ti electrode in the removal of toxic chlorinated PPCPs

Junjing Li,Menghua Yin,Yu Wang,Liang Wang

DOI: https://doi.org/10.1016/j.seppur.2023.125120

IF: 8.6

2023-09-28

Separation and Purification Technology

Abstract:In order to change the mass transfer efficiency of conventional flat plate electrodes in the catalytic process, a new filtered Pd@Ti electrode has been prepared. The results indicated that the filtered Pd@Ti electrode had the best removal efficiency of 99.59% on diclofenac (DCF) at the flux of 40.85 L/m 2 ∙h -1 . Compared to unfiltered Pd@Ti electrodes, the removal efficiency was 1.18 times higher, the current efficiency was 2.15 times higher and the cost of electricity was 69.05% lower. The electrocatalytic hydrodechlorination process of DCF by filtered Pd@Ti electrode mainly relies on indirect reductive dechlorination by H* adsorbed on the electrode surface. The removal efficiency of the filtered Pd@Ti electrode remained above 80% after six cycles. The removal mechanism and reaction pathway of filtered Pd@Ti electrode for dechlorination of different chlorinated PPCPs were proposed. Furthermore, the ecotoxicity of chlorinated PPCPs and their products were evaluated by using the toxicity estimation software tool (T.E.S.T.) model. This study confirmed the promising application of filtered Pd@Ti electrodes for the removal and detoxification of chlorinated PPCPs in wastewater.

engineering, chemical
Mechanism and Influence Factors of 2,4‐D Dechlorination by Sodium Citrate‐activated Bimetallic Palladium‐zero Valent Iron Nanoparticles

Hongyi Zhou,Yongkang Zhao,Junchao Xiang,Ning Huang,Shams Ali Baig,Sisi Zeng

DOI: https://doi.org/10.1002/aoc.5324

IF: 3.9

2019-01-01

Applied Organometallic Chemistry

Abstract:Nanoscale zero‐valent iron (nZVI) has high removal efficiency and strong reductive ability to organic contaminants, but this reactivity soon ceases and is attributed to rapid passivation of the nZVI surface due to the formation of iron oxides. In the present study, bimetallic palladium‐zero valent iron nanoparticles were activated with sodium citrate (SC‐nPd/Fe) to enhance 2,4‐D dechlorination from aqueous solutions. FTIR and XRD analyses showed that there was no passivation layer on the surface of nZVI after the addition of SC, and XPS analysis confirmed the nZVI after the reaction still maintained high reactivity and surface Pd ratio. The existence of SC facilitated the transfer of electrons from Fe0 to contaminants, thus accelerating the reductive dechlorination of 2,4‐D. The dechlorination efficiency of 2,4‐D on nPd/Fe was only 56.4% in 210 min, while complete dechlorination could be achieved on SC‐nPd/Fe under the same conditions, and simultaneously 97.1% of phenoxyacetic acid (PA) was generated. Moreover, the effect of reaction conditions on the dechlorination such as Pd ratio, SC dosage, initial pH and temperature was also investigated, and it was well described by pseudo‐first‐order kinetic model. In particular, The chelating abilities of SC is similar to EDTA, but it is an environmentally‐friendly chelating agent. Findings from the present study suggested that the SC could be a promising substitute for application in the remediation of 2,4‐D contained water.
The Dechlorination of Pentachlorophenol under a Sulfate and Iron Reduction Co-Occurring Anaerobic Environment

Lili Xue,Xi Feng,Yan Xu,Xinfeng Li,Min Zhu,Jianming Xu,Yan He

DOI: https://doi.org/10.1016/j.chemosphere.2017.04.124

IF: 8.8

2017-01-01

Chemosphere

Abstract:An anaerobic soil slurry incubation experiment was conducted by controlling different Fe/S mole ratios (1/3, 1/2, 1/1, 2/1, 3/1, 8/1 and the control without sulfate) through the addition of sodium sulfate, to investigate the effect of sulfate and iron reduction on the reductive dechlorination of pentachlorophenol (PCP). Two sequential incubation periods were carried out with the stage I incubation conducted under a low electron donor concentration (0.5 mM lactate) and stage II incubation conducted under increased electron donor supply with lactate at 20 mM. During stage I, the production of Fe(II) occurred markedly while sulfate reduction and PCP dechlorination rate were low, with the highest dechlorination rates of PCP only 11.0% among all treatments at the end of stage I incubation. During stage II, both PCP dechlorination and sulfate reduction were greatly enhanced in all treatments, while the concentration of Fe(II) changed slightly. The rate of PCP dechlorination decreased (from 87.7% to 34.2%) with the increase of sulfate concentration (from Fe/S mole ratio of 8/1 to 1/3). Our study suggested that the presence of a certain amount of sulfate might facilitate PCP dechlorination in the range of Fe/S mole ratios greater than 1 when compared with the control without SO42-. With the investigation of the dechlorination of PCP under the Fe-S-PCP coexisting condition with different Fe/S mole ratios, our study may provide improved strategy for optimizing the remediation of flooded soils and sediments polluted by PCP. (C) 2017 Elsevier Ltd. All rights reserved.
Pd/PANI/Ti composite electrocatalyst with efficient electrocatalytic performance: Synthesis, characterization, stability, kinetic studies, and degradation mechanism

Jian Zhang,Yue Zhao,Yuqing Liu,Chuntao Zhu,Bing Wang,Lanhe Zhang,Guomin Li,Hao Wu,Congze Liu,Yuanchun Li,Junlian Ren,Chen Shao,Xiangdong Zhang

DOI: https://doi.org/10.1016/j.jallcom.2022.163723

IF: 6.2

2022-05-01

Journal of Alloys and Compounds

Abstract:The unique structure of benzene ring and chloride ion makes chlorophenol pollutants have a great influence on biology and ecology. Due to its environmental friendliness, electrochemical methods have been widely used to degrade chlorophenol pollutants. Herein, the palladium/polyaniline/titanium (Pd/PANI/Ti) composite electrodes were prepared by the constant current method due to the high catalytic activity of palladium and the high specific surface area of polyaniline. The morphology, crystal structure, element valence, and functional groups of the composite electrodes were observed and analyzed by SEM, XRD, XPS, and FT-IR. The degradation efficiency of 2, 4-DCP in NaCl solution was up to 96.54% for 8 min and 100% for 10 min, respectively. The results show that the best removal efficiency of 2, 4-DCP by Pd/PANI/Ti electrode is as follows: the aniline concentration is 5 mL/L, the preparation voltage is 20 V, the concentration of PdCl2 is 10 μmol/L, the pH is 3, and the electrolyte NaCl concentration is 0.20 mol/L. The kinetics of the 2, 4-DCP degraded by Pd/PANI/Ti electrode was found to be pseudo-first-order kinetics and was fitted to the Langmuir–Hinshelwood model. The degradation products were analyzed by LC-EIS-MS. The removal efficiency of 2,4-DCP remained basically unchanged after 20 times of continuous use. The good removal efficiency of 2, 4-DCP indicates that this electrode is a promising material in the practical application of removing chlorophenol pollutants from water. Finally, the degradation pathway of 2,4-DCP was put forward.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Oxygenated functional group-driven spontaneous fabrication of Pd nanoparticles decorated porous carbon nanosheets for electrocatalytic hydrodechlorination of 4-chlorophenol

Qi Wang,Lingxi Zhou,Qian Chen,Mingyue Mao,Weidong Jiang,Yan Long,Guangyin Fan

DOI: https://doi.org/10.1016/j.jhazmat.2020.124456

IF: 13.6

2021-04-01

Journal of Hazardous Materials

Abstract:Researchers have been committed to reducing the hazardous pollutants by developing efficient catalysts while ignoring the pollution caused by the use of toxic surface capping agents, reductants and/or organic solvents in the catalyst preparation process. To alleviate such problems, we here report a novel one-step oxygenated functional group-driven electroless deposition strategy to synthesize clean and uniformly distributed Pd nanoparticles (NPs) using porous carbon nanosheets (PCN) as both substrates and reducing agents. It is observed that the oxygenated functional groups enriched PCN possesses a low work function and allows the spontaneous reduction of PdCl42- ions to Pd NPs deposited on the PCN support (Pd/PCN). The particle size of Pd NPs can be flexibly modulated by simply controlling the immersing time and thereby their maximum catalytic performances can be achieved. Specifically, the optimal Pd/PCN-08 with a Pd loading of 3.0 wt% shows an excellent activity with a turnover frequency of 0.38 min-1 for electrocatalytic hydrodechlorination (ECH) of 4-chlorophenol (4-CP), superior to the previously reported materials. The stability of Pd/PCN-08 for 4-CP ECH is impressive in repetitive cycles. This work proposes a facile and efficient strategy to synthesize high-performance catalysts for detoxifying the hazardous organic pollutants.

environmental sciences,engineering, environmental
Unveiling the mechanism and performance of electrocatalytic hydrodechlorination of chlorinated PPCPs by electron-rich palladium electrode modulated through PANI-rGO interlayer

Junjing Li,Kaizhou Kong,Yutong Chong,Jing Ding,Liang Wang,Zhengchun Ba,Jun Zhang

DOI: https://doi.org/10.1016/j.seppur.2023.124452

IF: 8.6

2023-07-07

Separation and Purification Technology

Abstract:In order to simultaneously achieve higher dispersion, smaller particle size, and better catalytic performance of Pd, a Pd/Polyaniline-reduced graphene oxide/Nickel foam (Pd/PANI-rGO/NF) electrode is synthesized by introducing conductive PANI-rGO interlayer for electrocatalytic hydrodechlorination (ECH) of typical chlorinated pharmaceuticals and personal care products (PPCPs). 99.3% diclofenac (DCF) and 94.6% clofibric acid (CA) are removed by this electrode within 180 min and the results of risk assessment show that the toxicities of the two typical chlorinated PPCPs are significantly reduced in the aqueous environment. The electrode is characterized and analyzed. The scanning electron microscopy (SEM) and transmission electron microscope (TEM) results indicate that the introduction of PANI-rGO effectively enhances the dispersion of Pd and reduces the size of Pd particle. Meanwhile, the combined analyses of X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS) and density functional theory (DFT) calculation suggest that electron transfer occurs between the PANI-rGO interlayer and Pd, leading to the formation of electron-rich Pd. Cyclic voltammetry (CV) curve indicates that the PANI-rGO interlayer improves the yield of active adsorbed hydrogen (H* ads ). Therefore, the catalytic activities of Pd particles are synergistically improved. This work can provide a beneficial choice for the effective treatment of typical chlorinated PPCPs in the water environment.

engineering, chemical
Electrocatalytic Dechlorination of 2,4-Dichlorophenoxyacetic Acid Using Nanosized Titanium Nitride Doped Palladium/nickel Foam Electrodes in Aqueous Solutions

Chen Sun,Shams Ali Baig,Zimo Lou,Jin Zhu,Zhuoxing Wang,Xia Li,Jiahan Wu,Yifu Zhang,Xinhua Xu

DOI: https://doi.org/10.1016/j.apcatb.2014.04.004

2014-01-01

Abstract:Nanosized titanium nitride (nTiN) doped palladium/nickel (Pd/Ni) foam electrodes were successfully prepared via electroless deposition method. The electrodes were evaluated by different techniques including field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and linear sweep voltammetry (LSV). FE-SEM images demonstrated that two different morphologies existed in the Pd layer after nTiN doping. The nTiN doped Pd/Ni foam electrodes were found to be highly effective for electrochemical reductive dechlorination of 2,4-dichlorophenoxyacetic acid (2,4-D) with excellent activity and stability, as revealed by batch experiments. Under the conditions of nTiN doping content of 2 mg, Pd loading of 0.44 mg cm(-2), the energetic electrode achieved nearly 100% removal of 2,4-D (0.226 mmol L-1) within 2 h at a current density of 1.667 mA cm(-2). However, the removal efficiency reached only 57.13% when a normal Pd/Ni foam electrode with identical Pd loading and current density was utilized. A successive 2,4-D reductive dechlorination process was observed. o-Chlorophenoxyacetic acid (o-CPA), p-chlorophenoxyacetic acid (p-CPA) and phenoxyacetic acid (PA) were detected and identified as transformation products. Regression analysis proved that the pseudo-first order kinetic model was not suitable to describe the dechlorination process on nTiN doped Pd/Ni foam electrodes due to the appearance of a plateau in the beginning of the curve. Moreover, an adsorption theory for Pd chemisorption of active hydrogen atom was proposed to better explain the phenomenon. An adsorption equilibrium of hydrogen existed in the Pd lattice between hydrogen in Pd solid solution and hydrogen in metal hydride, which would influence the effective utilization of active hydrogen atom [H] for dechlorination treatment. An indirect reduction mechanism of the 2,4-D dechlorination on the as-prepared electrodes was also elucidated. (C) 2014 Elsevier B.V. All rights reserved.
Atomically dispersed Pd electrocatalyst for efficient aqueous phase dechlorination reaction

Zhechuan Mao,Linghui Liu,Hong Bin Yang,Yangliang Zhang,Zeqing Yao,Huan Wu,Yanqiang Huang,Yinghua Xu,Bin Liu

DOI: https://doi.org/10.1016/j.electacta.2021.138886

IF: 6.6

2021-09-01

Electrochimica Acta

Abstract:High atom utilization is important for practical application of Pd catalysts in dechlorination of chlorinated organic pollutants (COPs). Herein, we report atomically dispersed Pd (coordinated with 2 pyridinic N) anchored on N-doped carbon (A-Pd-NC) as an efficient catalyst toward electrochemical dechlorination of COPs in aqueous solution. Constant current electrolysis showed that the A-Pd-NC catalyst possessed a much higher dechlorination activity (DA, 98.9 mmol•g−1•h−1) than commercial Pd/C (2.4 mmol•g−1•h−1). Using A-Pd-NC as an effective electrocatalyst, near 100% product selectivity of 4-chlorophenol to phenol could be achieved at pH = 3. Constant potential electrolysis, cyclic voltammetry (CV), electron spin resonance (ESR), X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculation results suggested that the dechlorination stability of A-Pd-NC was dependent on the potential applied on the catalyst and the dechlorination reaction followed the hydrodechlorination mechanism with electrochemically adsorbed H as the reductant.

electrochemistry
Preparation of Anatase Tio2/Ti Nanotube-Like Electrodes and Their High Photoelectrocatalytic Activity for the Degradation of Pcp in Aqueous Solution

SG Yang,YZ Liu,C Sun

DOI: https://doi.org/10.1016/j.apcata.2005.12.016

2006-01-01

Abstract:To further improve the photooxidation techniques for water and wastewater purification, we successfully prepared a new type of photoelectrode, a TiO2 nanotube electrode, first by a sol–gel method and then by treatment to form the tubular structure in NaOH aqueous solution. The structure, surface morphology and band gap energy of the Ti/TiO2 electrode were examined by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and UV–vis absorption microscopy, respectively. The examination results indicated that anatase TiO2 was dominant in its composition and a significant blue-shift in the spectrum of UV–vis absorption was observed. The photoelectrochemical efficiency of the nanotube-like TiO2/Ti electrode has been determined in terms of photocurrent, degradation and mineralization of PCP. To investigate its potentials in environmental applications, we studied the degradation of pentachlorophenol (PCP) in aqueous solution using photoelectrocatalytic (PEC) processes. The results were compared with those of electrochemical process (EP) and photocatalysis (PC). A significant photoelectrochemical synergetic effect was observed. The kinetic constant of PEC degradation of PCP using TiO2 nanotube electrode was 64.7% higher than that using TiO2 film electrode. The dependences of the rate constants on various parameters in the photoelectrocatalytic process, such as applied potential, electrolyte and pH value were investigated in detail. Degradation efficiency increased with increasing applied bias potential and concentration of Na2SO4. PEC degradation of PCP was more favorable in acidic solution than in alkali solution. There was an optimum pH value in the PEC process.
The electrocatalytic dechlorination of chloroacetic acids at electrodeposited Pd/Fe-modified carbon paper electrode

Angzhen Li,Xu Zhao,Yining Hou,Huijuan Liu,Liyuan Wu,Jiuhui Qu

DOI: https://doi.org/10.1016/j.apcatb.2011.11.016

2012-01-01

Abstract:Pd/Fe-modified carbon paper (Pd/Fe-C) electrode was prepared from PdCl2 and FeSO4 via electrodeposition onto carbon paper. It was observed that the diameters of electrodeposited Pd/Fe particles were around 20nm with a uniform distribution on carbon paper, which is smaller than Pd/Fe particles of impregnated and calcined electrode. The electrodeposited Pd/Fe-C electrode exhibited higher activity in dechlorination of chloroacetic acids than impregnated and calcined electrode. Under optimal experiment conditions of Pd:Fe molar ratio of 2:1 at −1.5V (vs SCE), 95% of trichloroacetic acid (TCAA) with the initial concentration of 500μg/L was removed within 20min at pH 3. The dechlorination of chloroacetic acids followed the order of TCAA>dichloroacetic acid (DCAA)>monochloroacetic acid (MCAA). MCAA cannot be dechlorinated at C and Fe-C electrodes via direct reduction. However, a part of chloroacetic acids was directly dechlorinated to acetic acid at Pd-C and Pd/Fe-C electrodes via indirect reduction. The Pd(0) and Pd(II) species were detected by X-ray photoelectron spectroscopy. Compared with the individual Pd-C electrode, in situ formation of Fe(0) decreased the interface impedance as observed by electrochemical impedance spectroscopy analysis. In conclusion, the presence of Pd(0) nanoparticles played a significant role in forming atomic H* to realize indirect reduction process which could achieve the complete dechlorination of chloroacetic acids.
Electrocatalytic dechlorination of 2,3,5-trichlorophenol on palladium/carbon nanotubes-nafion film/titanium mesh electrode

Zhirong Sun,Xiaoyue Ma,Xiang Hu

DOI: https://doi.org/10.1007/s11356-017-9004-7

IF: 5.8

2017-04-21

Environmental Science and Pollution Research

Abstract:Palladium/carbon nanotubes-nafion film-modified titanium mesh electrode (Pd/CNTs-nafion film/Ti electrode) was prepared and used for catalytic dechlorination of 2,3,5-trichlorophenol (2,3,5-TCP). The influences of factors, such as Pd2+ concentration, plating solution pH, and electrodeposition time and current, on the preparation of the electrode were studied by cyclic voltammetry (CV) to establish the optimal electrode preparation conditions. Additionally, the CV results highlighted that the addition of the CNTs-nafion film could enhance the electrochemical performance of the electrode. The Pd/CNTs-nafion film/Ti electrode was characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The electrode exhibited good stability and high catalytic dechlorination capacity on 2,3,5-TCP―100 mg L−1 2,3,5-TCP was completely dechlorinated within 100 min at a dechlorination current of 5 mA and an initial solution pH of 2.3. High-performance liquid chromatography (HPLC) was used to detect the chlorinated phenolic intermediates, and the results revealed that the final products were mainly phenol. The kinetics studies revealed that the dechlorination of 2,3,5-TCP followed two-stage mixed order kinetics, and a possible degradation pathway for 2,3,5-TCP was proposed.

environmental sciences
Enhanced Electrocatalytic Dechlorination by Dispersed and Moveable Activated Carbon Supported Palladium Catalyst

Jiasheng Zhou,Zimo Lou,Jiang Xu,Xiaoxin Zhou,Kunlun Yang,Xiaoyu Gao,Yilin Zhang,Xinhua Xu

DOI: https://doi.org/10.1016/j.cej.2018.10.098

IF: 15.1

2019-01-01

Chemical Engineering Journal

Abstract:In this study, a novel approach was developed for the dechlorination of 2,4-dichlorobenzoic acid (2,4-DCBA) via the combination of the moveable activated carbon (AC) supported palladium (Pd) nanoparticles and nickel (Ni) foam electrode. The morphology and chemical structure of Pd/AC catalyst was investigated by various characterization techniques, including SEM, TEM, EXS-mapping, XRD, and XPS. Pd nanoparticles was successfully loaded and dispersed on the AC, accompanied with the significantly enhanced reactivity. The removal rate of 2,4-DCBA by Ni electrode with moveable Pd/AC catalyst was 222, 25, and 5 folds higher than dispersed AC and Ni electrode system, chemical deposited Pd/Ni electrode, and electrodeposited Pd/Ni electrode, respectively. Compared with the conventional electrocatalytic reductive approach which deposited Pd on the Ni foam electrode, moveable Pd/AC catalyst possesses higher surface area, more atomic H∗ production and more active sites, favored mass transfer, and enhanced reactivity, without the consideration of catalyst loss and deactivation. The effects of Pd:AC mass ratio, constant current, initial solution pH, and electrolyte concentration on the dechlorination of 2,4-DCBA were studied. Generally, high Pd loading, constant current, and acidity favored the dechlorination of 2,4-DCBA, while excessive electrolyte would inhibit the dechlorination of 2,4-DCBA. Good longevity and recyclability of moveable Pd/AC catalyst was confirmed via consecutive experiments. The findings of the present study show that making the catalyst moveable is a promising strategy for electrocatalytic remediation technology.

Acoustic emissions during 3.1 MHz ultrasound bulk ablation in vitro.

Preparation and electrocatalytic dechlorination performance of Pd/Ti electrode

Complete dechlorination of 2,4-dichlorophenol in aqueous solution on palladium/polymeric pyrrole-cetyl trimethyl ammonium bromide/foam-nickel composite electrode.

Electrochemical degradation of pentachlorophenol on a palladium modified gas-diffusion electrode.

Electrochemical Dechlorination of 3-chlorophenol with Palladium-Loaded Carbon Felt Electrode

Bile salts increase epithelial cell proliferation through HuR-induced c-Myc expression.

Electrochemical Dechlorination of 2,4-Dichlorophenol in Aqueous Solution on Palladium-Loaded Meshed Titanium Electrode.

Electrocatalytic Hydrodechlorination of 2,4,5-Trichlorobiphenyl on A Palladium-Modified Nickel Foam Cathode

Electrochemical degradation of sodium pentachlorophenol on a Pd/C gas-diffusion electrode

Improvement of the conventional flat plate electrode: Application of filtered Pd@Ti electrode in the removal of toxic chlorinated PPCPs

Mechanism and Influence Factors of 2,4‐D Dechlorination by Sodium Citrate‐activated Bimetallic Palladium‐zero Valent Iron Nanoparticles

The Dechlorination of Pentachlorophenol under a Sulfate and Iron Reduction Co-Occurring Anaerobic Environment

Pd/PANI/Ti composite electrocatalyst with efficient electrocatalytic performance: Synthesis, characterization, stability, kinetic studies, and degradation mechanism

Oxygenated functional group-driven spontaneous fabrication of Pd nanoparticles decorated porous carbon nanosheets for electrocatalytic hydrodechlorination of 4-chlorophenol

Unveiling the mechanism and performance of electrocatalytic hydrodechlorination of chlorinated PPCPs by electron-rich palladium electrode modulated through PANI-rGO interlayer

Electrocatalytic Dechlorination of 2,4-Dichlorophenoxyacetic Acid Using Nanosized Titanium Nitride Doped Palladium/nickel Foam Electrodes in Aqueous Solutions

Atomically dispersed Pd electrocatalyst for efficient aqueous phase dechlorination reaction

Preparation of Anatase Tio2/Ti Nanotube-Like Electrodes and Their High Photoelectrocatalytic Activity for the Degradation of Pcp in Aqueous Solution

The electrocatalytic dechlorination of chloroacetic acids at electrodeposited Pd/Fe-modified carbon paper electrode

Electrocatalytic dechlorination of 2,3,5-trichlorophenol on palladium/carbon nanotubes-nafion film/titanium mesh electrode

Enhanced Electrocatalytic Dechlorination by Dispersed and Moveable Activated Carbon Supported Palladium Catalyst