Abstract:Heterogeneous 3D integration is being hailed as the driver for new technologies due to its stacked device architecture. This increases functionality as the number and length of interconnecting wires decreases, in turn decreasing power consumption. In these advanced packaging technologies, the metal redistribution layers (RDLs) and the insulating polymer surrounding them are crucial components on which stringent reliability requirements are placed. The metal RDL’s are necessary to reroute signals from device level to packaging level. The polymer insulator, used as an alternative to traditional dielectric materials, must (i) be photosensitive to be compatible with lithography processing steps, (ii) possess high mechanical strength, (iii) exhibit good electrical performance, (iv) have a high thermal stability and glass transition temperature, and crucially (v) it must not be hygroscopic. Low or no moisture uptake of the polymer is essential as any moisture can cause mechanical and electrical reliability issues. Absorbed moisture can cause oxidation of Cu lines leading to the well-known problem of Cu diffusion resulting in voids, contact issues, delamination, electromigration and higher leakage currents. Area selective deposition (ASD) could greatly benefit these RDL’s by preferentially depositing an oxygen barrier to stop the oxidation of the Cu lines. The proprietary polymer used in this work is part of the WPR series by JSR Corporation and is a thermosetting phenol-based polymer which displays a high mechanical stability as it contains rubber nanoparticles, 70 nm in diameter. These are added to the polymer to increase the toughness and to prevent cracks and fractures forming and propagating through the film. However, achieving ASD with this polymer is difficult as the polymer is designed to have good adhesion properties so it will easily adhere to the Cu in the metal lines, and there are two materials of interest to passivate, the polymer itself and the rubber nanoparticles. In this work the surface is passivated by utilizing a polymerizing octafluorocyclobutane (C 4 F 8 ) plasma which creates a Teflon-like film on the surface. The surface morphology and hydrophobicity are investigated to assess the best plasma exposure time, which was found to be 30 s. Surface chemistry from XPS analysis reveals surface modification through the deposition of fluorine rich groups from the 30 s C 4 F 8 plasma exposure, Figure 1(a). Water contact angle measurements reveal an initial hydrophobic surface (~94°) but this hydrophobicity decreases over the course of several seconds. Following the 30 s C 4 F 8 plasma exposure, the hydrophobicity increases significantly to above 110° and remains stable as shown in Figure 1(b). Surface morphology studies carried out by AFM demonstrates no increase in surface roughness following plasma exposure, Figure 1(c) and (d). ALD tests show the process to be selective to the tetrachloride family of ALD precursors. No selectivity was observed with tetrakis (dimethylamino) or isopropoxide based precursors. This process has the capability to block approximately 2 nm of TiO 2 and HfO 2 from these tetrachloride precursors. Studies of the same process on Cu substrates show that the metal surface is only temporarily modified, and ALD growth can still take place. Reliability stress and corrosion tests were performed to assess if the selectively deposited barriers could prevent Cu oxidation. Figure 1(a) C 1s XPS spectra showing difference before and after plasma treatment, (b) WCA value increases following plasma treatment, and AFM images in (c) and (d) show no change in the surface following plasma exposure. Figure 1

Adhesion of electron-beam evaporated SiO 2 /TiO 2 anti-reflective coating on ion-treated polycarbonate substrate under xenon arc accelerated weathering test

Anti-reflection Coating at 550 Nm Fabricated by Atomic Layer Deposition

Hard Antireflective Coatings in the Visible Band

Wide-angle Broadband Antireflection Coatings with Nano-Taper Hydrated Alumina Film.

Embedding constructed refractive index graded antireflective coating with high abrasion resistance and environmental stability for polycarbonate glass

Mechanically Robust Antireflective Coatings

Single Component: Bilayer TiO2 As a Durable Antireflective Coating

Optical and anisotropic stress properties of flexible (Ta2O5/SiO2)2 antireflection film deposited by E-gun evaporation with ion-beam assisted deposition

Large-area deposition of protective (Ti,Al)N coatings onto polycarbonate

Decorative Chromium Coatings on Polycarbonate Substrate for the Automotive Industry

Durable fluorinated-SiO2/epoxy superhydrophobic coatings on polycarbonate with strong interfacial adhesion enhanced by solvent-induced crystallization

Oxidation effects on graded porous silicon anti-reflection coatings

UVC Irradiation as a Surface Treatment of Polycarbonate to Generate Adhesion to Liquid Silicone Rubber in an Overmolding Process

The Effect of the Process Parameters on the Growth Rate and Composition of the Anti Scratch Films Deposited from TEOS by AP-PECVD on Polycarbonate

Sputtered anti-reflection layer on transparent polyimide substrate improves adhesion strength to copper layer: effects of layer thickness and sputtering power

Surface Passivation of Polymer Based Redistribution Layers for Area Selective Deposition of an Oxygen Barrier

Al<sub>2</sub>O<sub>3</sub> anti-reflection coatings with graded-refractive index profile for laser applications

Chemical and UV Durability of Hydrophobic and Icephobic Surface Layers on Femtosecond Laser Structured Stainless Steel

A durable superhydrophilic self-cleaning coating based on TiO 2 –SiO 2 -PAA nanocomposite for photovoltaic applications: Long-term outdoor study

Atomic oxygen effects on polymers containing silicon or phosphorus: Mass loss, erosion yield, and surface morphology

Low-Temperature Preparation of SiO2/Nb2O5/TiO2–SiO2 Broadband Antireflective Coating for the Visible via Acid-Catalyzed Sol–Gel Method