Abstract:Plastic bags and tubes are increasingly used for the storage and application of pharmaceutical formulations. The most common polymer material for drug application sets is plasticized poly(vinylchloride) (PVC). During application of pharmaceutical drug solution through PVC tubes, the polymer and the contact media interact which leads to leaching out of polymer additives or sorption of ingredients of the drug solution. Whereas the discussion of leaching of plasticizers is focussed on the toxicological properties of a drug packaging system, the sorption of drug formulation compounds has an influence on the dosage of the active pharmaceutical ingredient resulting in a reduced drug delivery to the patient. Therefore sorption has an influence on the effectiveness and success of the therapy. Within the study, the concentration profiles of nitroglycerin and diazepam solutions were determined after pumping the solutions through infusion administration sets. The study includes plasticized PVC tubes with different plasticizers (DEHP, DEHA, DEHT, TEHTM, DINCH, poly adipate), PVC (DEHP) tubes with different shore hardness as well as alternative polymer materials like EVA, TPE, PUR, silicone, LDPE and PP. From the experimental concentration curves it could be shown, that in the first minutes of the application of the drug solution the sorption of the active compound is at its maximum, resulting in the lowest concentration in the applied pharmaceutical solution. For a PVC tube with DEHP as plasticizer and a shore hardness of 80 only about 57% of the initial nitroglycerin concentration in the solution is applied to the patient in the first minutes of the application. For PVC tube (DEHP, shore 80) the experimental data were simulated using mathematical diffusion models. The concentration profiles during application could be well simulated using the partition coefficient K=50 (nitroglycerin) and K=300 (diazepam), respectively. However, the experimental results indicate, that the sorption of nitroglycerin into the PVC tube alters the diffusion behaviour of the polymer over flow time, which results in an increase of the diffusion coefficient during application. On the other hand, the other investigated alternative tube materials like PE or PP show a significantly lower sorption compared to PVC plasticizer systems. Due to the fact that the amount of sorption is varying over time, the concentration of the active pharmaceutical compound in the solution after passing the infusion administration set is not constant which makes the application of a constant concentration of a certain active ingredient to the patient very difficult. The simulated partition and diffusion coefficients for given PVC(DEHP) tubes were therefore used to simulate the initial concentrations profile of the feeding drug solution to assure a constant concentration flow profile after passing the administration set. The proposed methodology of this study represents a straight forward approach for the assessment of the drug sorption in dynamic flow systems based on experimental data as well as mathematical diffusion modelling. From the results a non-constant initial concentration profile for the active ingredient in a pharmaceutical drug solution can be established in order to compensate the loss of the pharmaceutical compound by sorption during infusion.

Influence of polyvinyl chloride infusion extension tube on propofol injection pain: a randomised controlled study

Intravenous Lidocaine Attenuates Response to Cervical Dilation for Hysteroscopy: a Randomised Controlled Trial

Clinical Observation of Fiurbiprofen Axetil Preceded by Venous Occlusion in Preventing Pain of Propofol Injection

The effect of temperature on di(2-ethylhexyl) phthalate leaching from PVC infusion sets exposed to lipid emulsions

Evaluation of efficacy of Valsalva maneuver for attenuating propofol injection pain: a prospective, randomized, single blind, placebo controlled study

Clinical observation on polyethersulphone filter noodle reducing propofol injection pain

Regulatory effects of propofol on high-dose remifentanil-induced hyperalgesia

Efficacy of cold propofol and lidocaine on propofol injection-induced pain

A comparison between target-controlled and manually controlled propofol infusions in patients undergoing routine surgical procedures.

The Leaching of Plasticizer from a Polyvinyl Chloride Container or a Parenteral Infusion Set into the Intravenous alprostadil Solution.

Effectivity of 5% Dextrose-Diluted and Ringer Lactate-Diluted Propofol to Reduce Intravenous Injection Pain in Pediatric Patient

Comparison Between Intravenous Nalbuphine and Lidocaine in Reducing Propofol-Induced Injection Pain During Gastroscopy: A Randomized Controlled Trial

Pain assessment in fentanyl-propofol combination: two dosage levels

Intravenous Dexmedetomidine Administration Prior Anesthesia Induction With Propofol at 4°C Attenuates Propofol Injection Pain: A Double-Blind, Randomized, Placebo-Controlled Trial

The extraction of diethylhexylphthalate (DEHP) from polyvinyl chloride components of intravenous infusion containers and administration sets by paclitaxel injection

Effect of Parecoxib Preapplication on Propofol Injection Pain

Effect of different doses of parecoxib pretreatment on propofol injection pain

Leaching of plasticizers from polyvinylchloride perfusion lines by different lipid emulsions for premature infants under clinical conditions

Comparing intensity of pain due to intravenous injection of sodium thiopental, propofol, diazepam, and etomidate during induction of general anesthesia

Comparison of Intravenous Ondansetron and Dexamethasone for Preventing Propofol-Induced Pain During Laparoscopic Cholecystectomy: A Double-Blind, Randomized Study

Investigation into the sorption of nitroglycerin and diazepam into PVC tubes and alternative tube materials during application