Physical, chemical and mechanical properties of pehuen cellulosic husk and its pehuen-starch based composites.

J. Castaño,S. Rodríguez-Llamazares,C. Carrasco,R. Bouza

DOI: https://doi.org/10.1016/j.carbpol.2012.07.029

IF: 10.723

2012-11-06

Carbohydrate Polymers

Abstract:

What problem does this paper attempt to address?

Power Control of Single Phase Grid-connected Inverter

CAO Lu-ping,SHEN Guo-qiao,ZHU Xuan-cai,XU De-hong

DOI: https://doi.org/10.3969/j.issn.1000-100x.2007.09.008

IF: 5.967

2007-01-01

IEEE Transactions on Power Electronics

Abstract:For the LCL filter adoptrd grid-connected inverter,when using weighted-average-current control method,there are the magnitude error and phase error at light load.And the forward feedback from the grid voltage makes the current under the influence of grid voltage.This paper proposes a new current control strategy using weighted-average-current as inner-loop and active/reactive current as out-loop.This method can control the grid current to have high magnitude and phase precision,also it will not be influenced by grid voltage.This paper presents the theoretical analysis and how to realize it.This control method has been experimentally tested on a 5kW grid-connected fuel cell inverter.
Impedance-based Analysis of Constant Reactive Power Control for Voltage Source Converter in Weak AC Grids

Luyao Xu,Hui Yuan,Zhou Lan,Huanhai Xin,Di Wu,Linbin Huang

DOI: https://doi.org/10.1109/pesgm40551.2019.8973597

2019-01-01

Abstract:When voltage source converters (VSCs) are connected to a weak AC grid, the constant reactive power control (CRPC) is more suitable for realizing optimal reactive power dispatch than the constant AC voltage control. This paper investigates the stability issues caused by the CRPC of VSCs. An impedance model of the VSC is developed which contributes to representing the CRPC dynamics characteristics. The impact of the CRPC parameters on the q-q channel impedance is analyzed. Then, a multiple-input multiple-output model is developed to analyze the small-signal stability of a grid-connected converter system. The eigenvalue analysis for the effects of both CRPC proportional gain and grid inductance on stability is presented. The impedance-based analysis reveals that the CRPC may cause medium-high frequency oscillations in the grid-connected converter system. Finally, time-domain simulations are conducted to validate the analysis.
A Systematic Approach Via IIR Filters for Enhancing the Robustness of LCL-Type Shunt Active Power Filters to Grid Impedance

Lei Yang,Jiaqiang Yang,Min Gao,Yunlong Chen,Xiang Zhang

DOI: https://doi.org/10.1109/tia.2020.2999273

IF: 4.079

2020-01-01

IEEE Transactions on Industry Applications

Abstract:A dual-loop current control method (grid current loop and inverter-side current loop) is promising for digitally controlled LCL-type shunt active power filters (APFs), due to its inherent active damping effect for LCL resonance. However, the damping region is only up to one-sixth of the sampling frequency $(f_{s}/ 6)$, which leads to limited system robustness against grid impedance variation at the point of common coupling (PCC). Hence, in this study, the robustness of such control is discussed through mathematic derivations and diagram analysis, which reveals that both the system delays and PCC voltage feedforward affect the system robustness. On the basis of theoretical analysis, a systematic approach via infinite impulse response (IIR) filters has been proposed for enhancing the robustness of grid impedance. Thereof, a second-order IIR filter-based inverter-side current feedback is proposed to widen the damping region up to almost the Nyquist frequency $(f_{s}/ 2)$, while a band-stop IIR filter-based PCC voltage feedforward is proposed to achieve the superior stability margins under a large grid impedance in comparison with unit feedforward. Finally, experimental results on a 30-kVA APF prototype have verified the effectiveness of the proposed approach.
Design and analysis of an LCL circuit-based three-phase grid-connected inverter

Jinhong Liu,Lin Zhou,Xirui Yu,Bin Li,Chen Zheng

DOI: https://doi.org/10.1049/iet-pel.2016.0351

IF: 2

2017-01-01

IET Power Electronics

Abstract:Owing to the inherent characteristics of grid-side inverters, a minimum dc-side voltage limit usually exists in grid-connected inverters. To solve this problem, this study proposes a convenient method of designing a novel LCL circuit for a grid-connected inverter, based on an LCL filter. The primary goal is to reduce the minimum dc-side voltage limit, while maintaining a considerably low harmonic ...
Power Decoupling Method Based On The Diagonal Compensating Matrix For Vsg-Controlled Parallel Inverters In The Microgrid

Bin Li,Lin Zhou

DOI: https://doi.org/10.3390/en10122159

IF: 3.2

2017-01-01

Energies

Abstract:The thought of the virtual synchronous generator (VSG) for controlling the grid-connected inverters and providing virtual inertia to the microgrid is emerging as a wide extension of the droop control, power coupling that always exists in the low-voltage microgrid, which may deteriorate the dynamic response and the stability of the system. In this paper, the principle of VSG control is introduced first. As an important issue of VSG control, the mechanism of the power coupling in the low-voltage microgrid is analyzed and the small-signal equivalent model of the power transmission loop is established. Subsequently, a power decoupling method based on the diagonal compensating matrix for VSG is proposed, which can realize the power decoupling with no impact on the original control channel. Meanwhile, the feasibility analysis of the decoupling method and the improved approach for reactive power sharing are also discussed. Simulation results verify the effectiveness of the decoupling strategy for VSGs.
Control strategies for the grid-connected inverter with LCL filter

Zhihong Bai,Xinbo Ruan,Lin Xu

2011-01-01

Abstract:Grid-connected inverter system with LCL filter is a third-ordersystem, which has a gain peak at its resonant frequency, and hence lower stability margin and involved complicated design of current regulators. In order to solve these problems, this paper proposes a novel control strategy with the combination of the grid (or inverter side) current feedback and another state variable feedforward, which can degrade the system order from the third to the first. Therefore, not only the stability margin is enlarged, but also the gain peak is eliminated and the current regulator design is greatly simplified. Besides, additional controls are also developed to attenuate the effects of grid voltage distortion or local load disturbance on the grid current, and the grid current waveforms can be further improved. Theoretical analysis, simulation and experimental results verified the proposition.
Linear Quadratic Optimal Control of a Single-Phase Grid-Connected Inverter with an LCL Filter.

Hao Tang,Rongxiang Zhao,Shengqing Tang,Zheng Zeng

DOI: https://doi.org/10.1109/isie.2012.6237114

2012-01-01

Abstract:A linear quadratic optimal control strategy for a single-phase grid-connected inverter with LCL filter is presented in this paper. Firstly, the mathematical model of the grid-connected inverter is investigated. Then, its linearized small signal state-space model is obtained, and a linear quadratic regulator (LQR) is achieved by the solution of algebraic Riccati equation (ARE). Finally, some simulations have been done on the MATLAB/Simulink platform in detail, which verifies the excellent performance of the proposed approach in steady-state and transient operation conditions.
Decentralized Power Sharing Control for Parallel-Connected Inverters in Islanded Single-Phase Micro-Grids

Keyou Wang,Xin Huang,Bo Fan,Qinmin Yang,Guojie Li,Mariesa L. Crow

DOI: https://doi.org/10.1109/tsg.2017.2720683

IF: 10.275

2018-01-01

IEEE Transactions on Smart Grid

Abstract:In this paper, a Lyapunov function-based decentralized control scheme is proposed for a single-phase parallel-connected inverters system within islanded micro-grid. With this novel method, a proper voltage regulation (e.g., amplitude and waveform quality) and excellent power and current sharing performance can be well ensured even in the presence of unknown line impedance and unbalanced LC filter parameters. In addition, high reliability and robustness can be guaranteed since no inter-communication among inverters as well as no centralized controller is demanded, which also delivers advantages of scalability and redundancy. The stability of the closed-loop system is ensured by standard Lyapunov method. The designation of the decentralized controller is simple to implement but rather effective. Detailed simulation and hardware-in-the-loop experimental results are presented to validate the feasibility of the proposed scheme under different operating conditions.
Analysis and Benchmarking of Grid-Forming Control for Power Converters

Jianbing Yin,Junhai Wang,Lin Chen,Mingchang Wang,Hao Luo,Yongheng Yang

DOI: https://doi.org/10.23919/icpe2023-ecceasia54778.2023.10213839

2023-01-01

Abstract:Traditional electricity grids use large-capacity synchronous generators as power generation devices, which have the characteristics of large volume and high robustness. In recent years, the rapid development of renewable energy in alignment with the national strategy of Carbon Neutrality in China by 2060 has brought new opportunities and challenges to traditional power grids. Power electronics converters are the key to renewable energy integration to gradually replace traditional synchronous generators, leading to reduced inertia and more challenges. While being more flexible, it makes the stability of the grid worse. In view of this, various advanced control strategies have been developed in the literature. The control of grid-connected converters has been broadly divided into two groups, grid-following (GFL) and grid-forming (GFM). In this paper, the characteristics of the GFM control are benchmarked through simulations, mainly the virtual synchronous generator (VSG) control and the virtual oscillator control (VOC). The benchmarking indicates that the VSG control strategies with virtual inertia have less fluctuation in response to various disturbances and the VOC performs better in terms of dynamics.
Modeling and Triple-Loop Control of ZVS Grid-Connected DC/AC Converters for Three-Phase Balanced Microinverter Application

Lin Chen,Changsheng Hu,Qian Zhang,Kun Zhang,Issa Batarseh

DOI: https://doi.org/10.1109/tpel.2014.2329278

IF: 5.967

2015-01-01

IEEE Transactions on Power Electronics

Abstract:This paper presents modeling and triple-loop control for a high-efficiency three-phase balanced inverter for using in grid-connected two-stage microinverter applications. An average signal model based on a synchronous rotation frame for a three-phase four-wire inverter has been developed. The inner current loop consists of a variable frequency bidirectional current mode (VFBCM) controller which regulates output filter inductor current thereby achieving ZVS, improved system response, and reduced grid current THD. Active damping of the LCL output filter using filter inductor current feedback is discussed along with small signal modeling of the proposed control method. Since the dc-link capacitor plays a critical role in two-stage microinverter applications, a dc-link controller is implemented outside of the two current control loops to keep the bus voltage constant. Finally, based on a two-stage 400-W prototype, simulation and experimental results are presented to verify the validity of the theoretical analysis, the effectiveness and feasibility of the proposed VFBCM control strategy.
A novel grid-connected converter with active power filtering function

Chao He,Xin Xie,Hui Yan,Chuan Xie,Guozhu Chen

DOI: https://doi.org/10.1016/j.egypro.2011.10.047

2011-01-01

Energy Procedia

Abstract:A Novel Grid-Connected Converter with ActivePower Filtering Function was proposed. Considering the specific situation, main circuit and controller were designed. The proposed system can exchange active power with grid and/or compensate harmonic current and reactive power of grid at the same time or respectively. LCL type filter was adopted to attain a good filtering effect. Proportional Integral (PI) control, repetitive control as well as feed forward control which can gain better dynamic performance composed the control system. To track the time-varying active current value, the influence of time lag caused by repetitive control during the fast switching period was considered. DC link voltage controller was designed for its special applications. Simulation results verify the high steady state precision and fast dynamic response of the system.
Experimental assessment of standalone inverter supplying AC load in microgrid system using an improved intelligent nonlinear control scheme

Kamal Elyaalaoui,Moussa Labbadi,Khalid Chigane,Mohammed Ouassaid,Mohamed Cherkaoui

DOI: https://doi.org/10.1007/s40435-022-00966-w

2023-03-28

International Journal of Dynamics and Control

Abstract:The experimental assessment of power quality for a standalone inverter connected to AC load in a microgrid is investigated in this paper. The microgrid used in this work includes photovoltaic solar and storage systems. The proposed control technique combined an intelligent method and sliding mode control (SMC) to make its structural more flexible. The power quality for AC load supply is enhanced, and the power loss, due to the harmonics of chattering effect and converter switching, is reduced. Moreover, the LCL filter is adopted for this microgrid to improve the power quality. The system stability is proved using Lyapunov theory and analysis. To validate the proposed design methodology and digital controllers and to show its superiority compared to other control techniques, experimental results are performed using a designed laboratory test bench for a standalone inverter system application and DSPace DS1104 board. In order to check advantages of the fuzzy SMC, the experimental results performed using the proposed LCL filter are compared to the conventional one to demonstrate its effectiveness in terms of harmonic attenuation and minimal power distortion. The experimental results show that the proposed technique provides the better operation with minimal distortion at the inverter output voltage.
Improved Model Predictive Direct Power Control of Grid Side Converter in Weak Grid Using Kalman Filter and DSOGI

Liang Chen,Heng Nian,Yunyang Xu

DOI: https://doi.org/10.23919/cjee.2019.000024

2019-01-01

Chinese Journal of Electrical Engineering

Abstract:When grid side converter (GSC) is connected to weak grid, the small signal instability can happen due to terminal characteristics of the GSC that are incompatible with the grid impedance. This issue is not of wide concern in previous studies of direct power control (DPC) of GSC. By small signal analysis, it is shown that the impedance characteristic of the conventional direct power control GSC is not compatible with the inductive grid impedance in weak grid due to its constant power load behavior. To solve the problem, instead of feeding the DPC controller with direct measured voltage and current, a Kalman filter (KF) is used to obtain filtered output current and a double second-order generalized integrator (DSOGI) is used to obtain filtered voltage at the point of common coupling (PCC). These strategies change the impedance characteristic of the GSC dramatically and make it suitable to operate in weak grid where SCR is 2, while the rapid power response is preserved. The proposed strategy is verified through simulation and controller hardware in loop (CHIL) tests.
Current control optimization for grid-tied inverters with grid impedance estimation

Guoqiao Shen,Junming Zhang,Xiaohui Li,Chengrui Du,Dehong Xu

DOI: https://doi.org/10.1109/APEC.2010.5433568

2010-01-01

Abstract:The control of a PWM inverter is affected by variable inductance present in the power line of the grid. This paper presents a new implementation of grid-tied inverter with weighted-average-current feedback control (WAC) and an embedded online technique to determine the grid line impedance. By adding an inter-harmonic voltage periodically in the modulation of the PWM and measuring the current response, it is possible to estimate the load impedance connected to the inverter, and the grid impedance can be obtained by subtracting the low-pass filter from the load impedance. Consequently, current control optimization can be carried out such as rearrangement of poles or zeroes and adjustment of the current loop gains to obtain the desired dynamic response even under changing line conditions. The presented technique can be implemented with the existing sensors and the digital processor of the inverter, provides a low cost and adaptive approach for current control of grid-tied inverters. Simulation on a 5kW grid-tied inverter demonstrates the control method and the impedance measurement.
Simplified Small Signal Analysis of Microgrid with the Droop and PQ Generators

Yuan-liang FAN,Quan-yuan JIANG,Yi-jia CAO

DOI: https://doi.org/10.3969/j.issn.1674-2974.2012.05.011

2012-01-01

Abstract:In order to simplify the Microgrid small signal model, only the dynamics of the power allocation loop of the droop generators and the dynamics of the DC voltage and reactive power output control loop of the PQ generator were considered. Normally, the filter reactance of the PQ generator is much larger than the Microgrids line impedance and the output power of the PQ generator is approximately controlled by the magnitude and phase of the inverter bridge voltage. By this approximation, the small signal model of the PQ generator can be in accordance with the droop generator by defining the small signals of the magnitude and phase of the output voltage as the model states. And in order to overcome the adverse impact of the big droop coefficients on the stability of the Microgrid, a feed forward path on the real power allocation loop was added to improve the stability. Lastly, time domain simulation confirmed the above analysis.
A novel control method for dual mode time-sharing grid-connected inverter

Weimin Wu,Houlai Geng,Pan Geng,Yinzhong Ye,Min Chen

DOI: https://doi.org/10.1109/ECCE.2010.5618077

2010-01-01

Abstract:A dual mode time-sharing inverter has higher efficiency than other type grid-connected inverter due to only one power stage of it working in high frequency state at any time. In this paper, small signal modeling of this inverter is carried out, which reveals that the control-to-grid current transfer function of this inverter has a right half plane zero at low frequency during the “Boost” operating stage which results in the difficulty in controlling the system. An indirect current control method based on instantaneous power balance is proposed. The right-half plane zero can be eliminated and a satisfactory compensator with enough phase margin and amplitude margin can be obtained with this new control strategy. And it is evaluated through simulation and experimental results of a 1kW prototype.
Enhancing grid-connected inverter performance under non-ideal grid conditions: a multi-functional multiplexing control strategy

Xianwen Bao,Lirong Zhang

DOI: https://doi.org/10.3389/fenrg.2024.1378808

IF: 3.4

2024-03-06

Frontiers in Energy Research

Abstract:Compared to the traditional thermal power generation, new energy sources, such as wind and photovoltaic systems, are more vulnerable to the effects of non-ideal power grids due to their limited capacity. This susceptibility can jeopardize the safe operation of power equipment, degrade power output quality, and lead to non-compliance with grid-connected specifications. The LCL-type grid-connected inverter is a typical nonlinear system that weakens the controllability of the grid-connected energy. To address these challenges, this study employs feedback linearization theory to transform the inverter into a standard linear system. Subsequently, it utilizes linear system methodologies to develop robust control laws, ultimately introducing a multi-functional multiplexing control strategy for grid-connected inverters based on feedback linearization and Hamilton-Jacobi-Issacs inequality. Simulation results demonstrate that this multi-functional strategy outperforms traditional grid-connected inverter control schemes, effectively mitigating issues related to low short-circuit ratios, voltage fluctuations, imbalances, harmonics, and other non-ideal grid conditions. Furthermore, it significantly expands the system's adaptability to varying weak grid impedances.

energy & fuels
Research on control of two-stage three-phase photovoltaic grid-connected inverter

Zhengfang Cao,Weibing Hu,Weihua Jiang

DOI: https://doi.org/10.1109/AICIT55386.2022.9930245

2022-09-16

Abstract:The variable-step incremental conductance method with the introduction of a power prediction link is proposed to address the problem of low light energy utilization and large distortion of grid-connected current in two-stage photovoltaic grid-connected inverters. This control method can optimize the positive dynamic speed and tracking accuracy of the maximum power point tracking control (MPPT). The coupling relationship under the dq synchronous rotation coordinate system and the influence are analyzed depending on the mathematical model of inverter-side photovoltaic grid connection. The grid-connected control adopts a voltage and current double closed-loop control method. A simulation model of the two-stage three-phase photovoltaic grid-connected inverter is constructed and studied in Matlab/Simulink. The simulation results show that the control method has fast response speed and small distortion of grid connected current waveform, which demonstrates the correctness of the control method.

Engineering,Environmental Science
Modeling simulation and inverter control strategy research of microgrid in grid-connected and island mode

Hui Wang,Mingyue Wang,Qi Cheng,Shuaishuai Lv,Xiu Ji

DOI: https://doi.org/10.1016/j.egyr.2022.09.117

IF: 5.2

2022-11-01

Energy Reports

Abstract:Under the “double carbon” goal, distributed generation (DG) with inverters will show an explosive growth trend. The microgrid can operate in different modes as a channel for DG to connect to the main grid. In the microgrid, the fast response characteristics of power electronics exacerbate the instability of the microgrid when switching between grid-connected and islanded modes. On the PSCAD/EMTDC simulation platform, a refined power generation model with wind–solar–load–storage microgrid is built to capture the behavior of the system, rather than using a highly simplified model. At the same time, a reasonable control strategy is necessary, which is the key to maintaining the stability of the system. Existing control strategies can only operate in a single mode or the control effect is not ideal. Based on this, on the basis of droop control, the virtual adaptive control loop is added in this study, and the virtual impedance value is adaptively changed according to different output conditions to achieve the purpose of precise control; In the active power control loop, the frequency signal is drawn from the phase-locked loop, and becomes a power feedback variable through the signal transformation process, thereby participating in the power control process and improving the accuracy of frequency control. A standard microgrid power generation model and an inverter control model suitable for grid-connected and off-grid microgrids are built, and the voltage and frequency fluctuations in the two modes are analyzed to verify the effectiveness of the strategy.

energy & fuels
Research on Fuzzy Active Disturbance Rejection Control of LCL Grid-Connected Inverter Based on Passivity-Based Control in Weak Grid

Hao Yan,Huafeng Cai

DOI: https://doi.org/10.3390/electronics12081847

IF: 2.9

2023-04-14

Electronics

Abstract:In response to the problems of impedance variation and rich background harmonics in the weak grid environment of traditional LCL grid-connected inverters, which cause distortion of the grid-connected current and reduce the stability of the entire grid-connected system, this paper proposes a passive fuzzy-active disturbance rejection control strategy. Firstly, passivity-based control (PBC) is introduced into the grid-connected inverter system to ensure the global stability of the entire system. Secondly, in order to solve the problem of difficult selection of inverter-side current, active disturbance rejection control (ADRC) is used to directly track the grid-connected current, avoiding the tracking error of AC signal and suppressing the interference of background harmonics of grid voltage. The combination of fuzzy control and ADRC simplifies the system parameter tuning process, and the FUZZY-ADRC grid-connected current outer loop and PBC inductance current inner loop are combined to form a multi-loop control system. Finally, simulation comparison verifies that the proposed control strategy can effectively suppress the harmonics of grid-connected current, improve the quality of grid-connected current, and enhance the stability of the entire grid-connected system in a weak grid environment.

engineering, electrical & electronic,computer science, information systems,physics, applied

Physical, chemical and mechanical properties of pehuen cellulosic husk and its pehuen-starch based composites.

Power Control of Single Phase Grid-connected Inverter

Impedance-based Analysis of Constant Reactive Power Control for Voltage Source Converter in Weak AC Grids

A Systematic Approach Via IIR Filters for Enhancing the Robustness of LCL-Type Shunt Active Power Filters to Grid Impedance

Design and analysis of an LCL circuit-based three-phase grid-connected inverter

Power Decoupling Method Based On The Diagonal Compensating Matrix For Vsg-Controlled Parallel Inverters In The Microgrid

Control strategies for the grid-connected inverter with LCL filter

Linear Quadratic Optimal Control of a Single-Phase Grid-Connected Inverter with an LCL Filter.

Decentralized Power Sharing Control for Parallel-Connected Inverters in Islanded Single-Phase Micro-Grids

Analysis and Benchmarking of Grid-Forming Control for Power Converters

Modeling and Triple-Loop Control of ZVS Grid-Connected DC/AC Converters for Three-Phase Balanced Microinverter Application

A novel grid-connected converter with active power filtering function

Experimental assessment of standalone inverter supplying AC load in microgrid system using an improved intelligent nonlinear control scheme

Improved Model Predictive Direct Power Control of Grid Side Converter in Weak Grid Using Kalman Filter and DSOGI

Current control optimization for grid-tied inverters with grid impedance estimation

Simplified Small Signal Analysis of Microgrid with the Droop and PQ Generators

A novel control method for dual mode time-sharing grid-connected inverter

Enhancing grid-connected inverter performance under non-ideal grid conditions: a multi-functional multiplexing control strategy

Research on control of two-stage three-phase photovoltaic grid-connected inverter

Modeling simulation and inverter control strategy research of microgrid in grid-connected and island mode

Research on Fuzzy Active Disturbance Rejection Control of LCL Grid-Connected Inverter Based on Passivity-Based Control in Weak Grid