Abstract:Thin films and van der Waals heterostructures derived from two-dimensional solids offer enormous potential for a broad range of novel, energy efficient devices, however, their use is currently hampered by slow, labor-intensive fabrication methods often employing hazardous chemicals. We demonstrate a novel technique for rapid, low-cost and environmentally-friendly production of ultra-thin films and van der Waals heterostructures of two-dimensional solids from aqueous surfactant-stabilized suspensions, which we term `Liquid Interface Deposition'. Films are produced by the transfer of platelets of two-dimensional materials assembled at the interface between two immiscible liquids (water and dicholoromethane), at which surfactants which stabilize the two-dimensional materials in the aqueous phase are `stripped' from the platelets due to preferential partitioning of the surfactant to the non-aqeuous phase. The approach is generic to two-dimensional materials which can be stabilized in aqueous suspension by a surfactant and the resulting films can then be transferred to an arbitrary substrate by a range of approaches. The generic applicability of this technique is demonstrated through production of thin films on a variety of substrates, deposition of transparent, highly conductive, graphene films with conductivities between $7.7 \times 10^{3} - 1.26\times 10^{5}~\textrm{S m}^{-1}$ and transmittances of 55-75%, and by the fabrication of van der Waals heterostructures of MoS$_2$, WS$_2$, and few-layer graphene.

What problem does this paper attempt to address?

The main problems that this paper attempts to solve are the problems existing in the current preparation methods of two - dimensional material (2D materials) thin films and van der Waals heterostructures (vdWHs). These problems include: 1. **Time - consuming and labor - intensive preparation methods**: Traditional preparation methods usually require a large amount of manual operation, the process is complex, and it is difficult to achieve large - scale production. 2. **Use of harmful chemicals**: Many traditional methods will use environmentally unfriendly chemicals during the preparation process, increasing the risk of environmental pollution. 3. **Lack of universality**: Existing preparation techniques are often only applicable to specific types of two - dimensional materials and lack wide applicability. In order to overcome these challenges, the paper proposes a new technology named "Liquid Interface Deposition" (LID). The main features of the LID technology include: - **Fast and low - cost**: The preparation time from raw materials to the final thin film or vdWHs is approximately 7 hours, and the cost is low. - **Environment - friendly**: It minimizes the use of harmful chemicals and reduces environmental impacts by recycling chemicals in the process. - **High universality**: It is applicable to a variety of two - dimensional materials that can be stably suspended in the aqueous phase without the need for pre - treatment of the substrate. - **Easy for large - scale production**: The preparation of precursor suspensions and the deposition process can be easily extended to large - scale production, with low energy consumption and low requirements for equipment and technology. The specific mechanisms of the LID technology include: 1. **Interface assembly**: By assembling two - dimensional material sheets at the interface of two immiscible liquids (such as water and dichloromethane), a thickness - controllable thin film is formed. 2. **Removal of multi - layer sheets**: If the initial suspension contains multi - layer sheets, they can be removed from the thin film by methods such as centrifugation. 3. **Removal of surfactants**: At the interface, surfactants will preferentially migrate to the non - aqueous phase, thereby peeling off from the two - dimensional material sheets to form a clean and pollution - free thin film. Through these steps, the LID technology can efficiently and environmentally - friendly prepare high - quality two - dimensional material thin films and vdWHs, providing new possibilities for future energy - efficient devices and other applications.

A Novel Liquid-Liquid Interface Deposition Method for the Production of Thin Films and van der Waals Heterostructures of Two-Dimensional Solids

Liquid Heterostructures: Generation of Liquid-Liquid Interfaces in Free-Flowing Liquid Sheets

Ultra-clean assembly of van der Waals heterostructures

Wafer-Scale and Full-Coverage Two-Dimensional Molecular Monolayers Strained by Solvent Surface Tension Balance

Scalable transparent conductive thin films with electronically passive interfaces for direct chemical vapor deposition of 2D materials

Thin-suspended 2D Materials: Facile, Versatile, and Deterministic Transfer Assembly

Facile fabrication of 2D material multilayers and vdW heterostructures with multimodal microscopy and AFM characterization

Suspended dry pick-up and flip-over assembly for van der Waals heterostructures with ultra-clean surfaces

PREPARATION OF THIN FILMS FROM MULTI-LAYER 2D NANOMATERIALS LIQUID

Nanosheet-stabilized emulsions: ultra-low loading segregated networks and surface energy determination of pristine few-layer 2D materials

Two dimensional crystals in three dimensions: electronic decoupling of single-layered platelets in colloidal nanoparticles

Liquid Metals: A Novel Possibility of Fabricating 2D Metal Oxides

Two-Dimensional Van Der Waals Thin Film and Device

Simultaneous Assembly of van der Waals Heterostructures into Multiple Nanodevices

Scalable synthesis of 2D van der Waals superlattices

Electrochemical molecular intercalation and exfoliation of solution-processable two-dimensional crystals

Electronically Tunable Transparent Conductive Thin Films for Scalable Integration of 2D Materials with Passive 2D–3D Interfaces

Ultrasonic delamination based adhesion testing for high-throughput assembly of van der Waals heterostructures

Production of Ultra-Thin and High-Quality Nanosheet Networks via Layer-by-Layer Assembly at Liquid-Liquid Interfaces

Atomic layer deposition of stable 2D materials

Synthesis of an aqueous, air-stable, superconducting 1T'-WS$_2$ monolayer-ink