Abstract:The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets of optical edge sensors are used per segment-to-segment edge, separated by a finite distance along the segment edge, for four optical heads, each with an imager and a collimator. By orienting the beam direction of one edge sensor pair to be +45 away from the segment edge direction, and the other sensor pair to be oriented -45 away from the segment edge direction, all six degrees of freedom of relative motion between the segments can be measured with some redundancy. The software resides in a computer that receives each of the optical edge sensor signals, as well as telescope pointing commands. It feeds back the edge sensor signals to keep the primary mirror figure within specification. It uses a feed-forward control to compensate for global effects such as decollimation of the primary and secondary mirrors due to gravity sag as the telescope pointing changes to track science objects. Three segment position actuators will be provided per segment to enable controlled motions in the piston, tip, and tilt degrees of freedom. These actuators are driven by the software, providing the optical changes needed to keep the telescope phased.

Tuning the MAPS Adaptive Secondary Mirror: Actuator Control, PID Tuning, Power Spectra and Failure Diagnosis

The MAPS Adaptive Secondary Mirror: First Light, Laboratory Work, and Achievements

Development and status of MAPS, the MMT AO exoPlanet characterization system

Novel Electro-Hydraulic Position Control System for Primary Mirror Supporting System

ESCAPE: Efficient Synthesis of Calibrations for Adaptive optics through Pseudo-synthetic and Empirical methods

Design and development of a high-speed Visible Pyramid Wavefront Sensor for the MMT AO system

An adaptive optics upgrade for the Automated Planet Finder Telescope using an adaptive secondary mirror

First laboratory and on-sky results of an adaptive secondary mirror with TNO-style actuators on the NASA Infrared Telescope Facility

In-lab and On-sky Closed-loop Results of Adaptive Secondary Mirrors with TNO's Hybrid Variable Reluctance Actuators

Design, Implementation and Testing of the MAP Radiometers

MagAO-X Phase II Upgrades: Implementation and First On-Sky Results of a New Post-AO 1000 Actuator Deformable Mirror

Wavefront Compensation Segmented Mirror Sensing and Control

Keck Primary Mirror Closed-Loop Segment Control using a Vector-Zernike Wavefront Sensor

Experiments on Quasi-Static and Dynamic Control of a PVDF Laminated Membrane-Like Mirror

Preliminary Control-Oriented Modeling of the ITER Steering Mirror Assembly and Local Control System in the Electron Cyclotron Heating & Current Drive Actuator

KAPAO: a MEMS-based natural guide star adaptive optics system

Development of a Miniaturized Deformable Mirror Controller

Design and Tests of Muti-motors Hydromantic Position Control System of Primary Mirror Based on Large Telescope

A novel method for adaptive control of deformable mirrors

System Integration Design of High-Performance Piezo-Actuated Fast-Steering Mirror for Laser Beam Steering System