Abstract:The present research aims to enhance the efficiency of a DTU-10MW Horizontal Axis Wind Turbine (HAWT) via Active Flow Control (AFC) implementation and using Synthetic Jets (SJ). In the initial part of the study the flow around two airfoil sections cut along the wing turbine blade and for a wind speed of 10m/s is simulated using CFD-2D-RANS-K{\omega}-SST turbulence model, in order to obtain the time averaged boundary layer separation point and the associated vortex shedding frequency. This information is used, on a second stage of the paper, to set, in one of these two airfoils where the boundary layer is having an early separation, two of the AFC parameters while optimizing the remaining three. The optimization is performed employing a parametric analysis and demonstrates that a considerable WT power increase can be obtained when managing to reattach the former separated boundary layer. This is further clarified thanks to the energy assessment presented in the final part of the paper. Although the AFC optimization needs to be extended for the rest of the blade sections, the procedure outlined in the present research clarifies the different steps to be followed to optimize the performance of any HAWT under any operating conditions. The Reynolds numbers associated to the respective airfoil sections analyzed in the present manuscript are Re = 14.088 e6 and Re = 14.877 e6, the characteristic length being the corresponding chord length for each airfoil.
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to improve the efficiency of wind turbines by implementing Active Flow Control (AFC) technology, especially using Synthetic Jets (SJ), on the DTU - 10MW Horizontal - Axis Wind Turbine (HAWT). Specifically, the researchers hope to delay boundary - layer separation by optimizing AFC parameters, such as the position, width, injection angle, frequency, and momentum coefficient of the synthetic jets, thereby reducing vortex shedding and ultimately increasing the power output of the wind turbine.
### Background and Objectives of the Paper
1. **Research Background**:
- Active Flow Control (AFC) technology interacts with the boundary layer by adding or subtracting momentum to the mainstream to delay its separation, thereby improving aerodynamic efficiency.
- Compared with passive flow control methods, AFC technology does not increase drag under off - design conditions.
- The Synthetic Jet (SJ) is a particularly effective AFC device that does not require an external fluid supply and performs excellently in controlling boundary - layer separation.
2. **Research Objectives**:
- **Improve Wind Turbine Efficiency**: Improve the efficiency of wind turbines by implementing AFC technology, especially using synthetic jets, on the DTU - 10MW HAWT.
- **Optimize AFC Parameters**: Through parameter optimization, determine the optimal position, width, injection angle, frequency, and momentum coefficient of the synthetic jets to minimize the required energy and maximize the performance improvement of the wind turbine.
- **Verify the Effectiveness of the Method**: Prove the effectiveness of the proposed AFC parameter optimization method through numerical simulation and experimental verification.
### Research Methods
1. **Numerical Simulation**:
- Use the CFD - 2D - RANS - K ω - SST turbulence model to simulate the flow conditions of two airfoil sections at a wind speed of 10m/s, and obtain the time - averaged boundary - layer separation point and the relevant vortex - shedding frequency.
- Through parameter optimization, determine the optimal AFC parameters to re - attach the separated boundary layer and increase the power output of the wind turbine.
2. **Experimental Verification**:
- Verify the numerical simulation results through experiments to ensure the effectiveness of the optimized AFC parameters in practical applications.
### Key Formulas
- **Momentum Coefficient \( C_\mu \)**:
\[
C_\mu=\frac{h \rho_{\text{jet}}(U_j^2) \sin \theta}{C \rho_\infty(U_\infty^2)}
\]
where \( h \) is the injector width, \( \rho_{\text{jet}} \) and \( \rho_\infty \) are the densities of the injector and the far - field respectively, \( U_j \) is the maximum injection velocity, \( C \) is the airfoil chord length, \( U_\infty \) is the free - stream velocity, and \( \theta \) is the inclination angle of the injector relative to the adjacent surface.
- **Dimensionless Frequency \( F^+ \)**:
\[
F^+=\frac{f C}{U_\infty}
\]
where \( f \) is the natural frequency of the boundary layer.
### Conclusion
This paper successfully improves the efficiency of the DTU - 10MW HAWT through numerical simulation and parameter optimization. The research results show that by optimizing AFC parameters, boundary - layer separation can be significantly delayed, vortex shedding can be reduced, and thus the power output of the wind turbine can be increased. Although the current research mainly focuses on two airfoil sections, the proposed method can be extended to the entire blade to further optimize the performance of any HAWT under various working conditions.