Abstract:Survival of the production target in successive experiments (with a repetition rate of 1 Hz) over an extended period of time is one of the key problems encountered in designing the Super-FRS (Superconducting Fragment Separator) at the future Facility for Antiprotons and Ion Research (FAIR). Because of the difficulties involved in construction of a liquid jet metal target, it is highly desirable to employ a solid production target at the Super-FRS. However, with the high beam intensities that will be available at the FAIR, the production target may be destroyed in a single experiment due to high specific energy deposition by the beam in the target material. The level of specific energy deposition can be reduced to an acceptable value by increasing the beam focal spot area. However, the spot size is limited by requirements of achieving good isotope resolution and sufficient transmission of the secondary beam through the system. The resolving power of the fragment separator is inversely proportional to the X-dimension of the focal spot whereas the transmission depends on Y-dimension only. It has been previously shown [Tahir et al., 2005c] that an elliptic focal spot with appropriate dimensions, will fulfill the above two conditions simultaneously and will also have a large enough area to reduce the specific energy deposition to an acceptable level for certain beam intensities of interest. In this paper we present numerical simulations of thermodynamic and hydrodynamic behavior of a solid graphite target that is irradiated by 1 GeV/u uranium beam in the intensity range of 10(10)-10(11) ions per bunch with a bunch length = 50 ns, These simulations have been carried out using a three-dimensional computer code, PIC3D, that includes elastic-plastic effects. This theoretical work has shown that up to a beam intensity of 10(11) ions/bunch, one can employ a solid target while for higher intensities the target will be destroyed due to thermal stresses induced by the beam. It has also been found that a circular focal spot leads to minimum thermal stresses as it generates minimum pressure gradients compared to an elliptic focal spot, for the same specific energy deposition. Moreover, the stress level increases with an increase in the ellipticity of the focal spot. It is therefore recommended that one should use a circular focal spot for lower intensities provided that the criteria for isotope resolution and transmission are fulfilled.

Multiphysics Simulations of Thermal Shock Testing of Nanofibrous High Power Targets

Novel materials for next-generation accelerator target facilities

High Energy Density and Beam Induced Stress Related Issues in Solid Graphite Super-Frs Fast Extraction Targets

Bayesian optimization scheme for the design of a nanofibrous high power target

Generation of Warm Dense Matter and Strongly Coupled Plasmas Using the High Radiation on Materials Facility at the CERN Super Proton Synchrotron

Radiation damage and thermal shock response of carbon-fiber-reinforced materials to intense high-energy proton beams

Ultra-High Gradient Channeling Acceleration in Nanostructures: Design/Progress of Proof-of-Concept (POC) Experiments

Numerical modeling of heavy ion induced stress waves in solid targets

CERN antiproton target: hydrocode analysis of its core material dynamic response under proton beam impact

High Energy Density Physics Problems Related to Liquid Jet Lithium Target for Super-Frs Fast Extraction Scheme

Necessity of Bunch Compression for Heavy-Ion-induced Hydrodynamics and Studies of Beam Fragmentation in Solid Targets at a Proposed Synchrotron Facility.

Targetry Challenges at Megawatt Proton Accelerator Facilities

Heavy-Ion-Beam-Induced Hydrodynamic Effects in Solid Targets

High-power Production Targets for the Super-FRS Using a Fast Extraction Scheme

Studies of material properties under irradiation at BNL Linear Isotope Producer (BLIP)

Probing the losses for a high power beam

Power deposition studies for standard and crystal-assisted heavy ion collimation inthe CERN Large Hadron Collider

Theoretical Simulation of Thermal Behavior in Transient Heat Loads Testing of Plasma-Facing Materials

Simulations of A Solid Graphite Target for High Intensity Fast Extracted Uranium Beams for the Super-Frs

The CERN Super Proton Synchrotron As a Tool to Study High Energy Density Physics

Post-irradiation examination of a prototype tantalum-clad target for the Beam Dump Facility at CERN