Abstract:Purpose Spectral CT uses energy-dependent measurements that enable material discrimination in addition to reconstruction of structural information. Flat-panel detectors (FPDs) have been widely used in dedicated and interventional systems to deliver high spatial resolution, volumetric cone-beam CT (CBCT) in compact and OR-friendly designs. In this work, we derive a model-based method that facilitates high-resolution material decomposition in a spectral CBCT system equipped with a prototype dual-layer FPD. Through high-fidelity modeling of multilayer detector, we seek to avoid resolution loss that is present in more traditional processing and decomposition approaches. Method A physical model for spectral measurements in dual-layer flat-panel CBCT is developed including layer-dependent differences in system geometry, spectral sensitivities, and detector blur (e.g., due to varied scintillator thicknesses). This forward model is integrated into a model-based material decomposition (MBMD) method based on minimization of a penalized weighted least-squared (PWLS) objective function. The noise and resolution performance of this approach was compared with traditional projection-domain decomposition (PDD) and image-domain decomposition (IDD) approaches as well as one-step MBMD with lower-fidelity models that use approximated geometry, projection interpolation, or an idealized system geometry without system blur model. Physical studies using high-resolution three-dimensional (3D)-printed water-iodine phantoms were conducted to demonstrate the high-resolution imaging performance of the compared decomposition methods in iodine basis images and synthetic monoenergetic images. Results Physical experiments demonstrate that the MBMD methods incorporating an accurate geometry model can yield higher spatial resolution iodine basis images and synthetic monoenergetic images than PDD and IDD results at the same noise level. MBMD with blur modeling can further improve the spatial-resolution compared with the decomposition results obtained with IDD, PDD, and MBMD methods with lower-fidelity models. Using the MBMD without or with blur model can increase the absolute modulation at 1.75 lp/mm by 10% and 22% compared with IDD at the same noise level. Conclusion The proposed model-based material decomposition method for a dual-layer flat-panel CBCT system has demonstrated an ability to extend high-resolution performance through sophisticated detector modeling including the layer-dependent blur. The proposed work has the potential to not only facilitate high-resolution spectral CT in interventional and dedicated CBCT systems, but may also provide the opportunity to evaluate different flat-panel design trade-offs including multilayer FPDs with mismatched geometries, scintillator thicknesses, and spectral sensitivities.

MACE CT Reconstruction for Modular Material Decomposition from Energy Resolving Photon-Counting Data

Material decomposition from photon-counting CT using a convolutional neural network and energy-integrating CT training labels

Material decomposition with a prototype photon-counting detector CT system: expanding a stoichiometric dual-energy CT method via energy bin optimization and K-edge imaging

Iterative Clustering Material Decomposition Aided by Empirical Spectral Correction for High-Resolution Photon-Counting Detectors in Micro-CT

Accurate Multi-Material Decomposition in Dual-Energy CT: A Phantom Study

Image Domain Multi-Material Decomposition Using Single Energy CT.

An Empirical Material Decomposition Method (EMDM) for Spectral CT

A method for material decomposition and quantification with grating based phase CT

Dual source hybrid spectral micro-CT using an energy-integrating and a photon-counting detector

Quantitative material decomposition using spectral computed tomography with an energy-resolved photon-counting detector

Robust Multimaterial Decomposition of Spectral CT Using Convolutional Neural Networks

High-resolution model-based material decomposition in dual-layer flat-panel CBCT

Photon-counting detector step-wedge calibration enabling water and iodine material decomposition

Image-domain Material Decomposition Based on Spectra Recovery in Spectral CT with Photon-counting Detectors

Spectral CT Two-step and One-step Material Decomposition using Diffusion Posterior Sampling

Iterative Material Decomposition Method Eliminating Photoelectric Effect for Dual-MeV Energy Computed Tomography

Model-based Material Decomposition with System Blur Modeling

High-Resolution Model-based Material Decomposition for Multi-Layer Flat-Panel Detectors.

A unified image reconstruction framework for quantitative dual- and triple-energy CT imaging of material compositions

ROI-Wise Material Decomposition in Spectral Photon-Counting CT

Direct Iterative Reconstruction of Multiple Basis Material Images in Photon-counting Spectral CT