Abstract:In a previous publication [Macromolecules2019,52, 5245–5254], we described the synthesis of surfactant-free latex dispersions of nanoparticles (NPs) based on emulsification of a preformed proprietary BASF polymer (MnGPC = 5000 g/mol, D̵ = 3), in which the −COOH groups were partially neutralized by using ammonia. The NPs in these dispersions were then partially cross-linked with neopentyl glycol diglycidyl ether (NGDE) to increase the molecular weight, followed by reaction with monoglycidyl ether to reduce the acid number and lower the glass transition temperature (Tg). In the work reported here, we used fluorescence resonance energy transfer (FRET) measurements to examine polymer diffusion rates in the films formed from these dispersions. We compared films formed from the uncross-linked NPs, with ones containing the NPs partially cross-linked with NGDE but not reacted with the monoepoxide. In this way, both the cross-linked and noncross-linked polymers had similar Tg values. We also examined films formed from a similar polymer with MnGPC = 4000 g/mol, D̵ = 3. Because of the high Tg of these polymers (ca. 65 °C), films were formed on heated substrates, and this led to skin formation at the film surface. We used FRET measurements to monitor the extent of polymer diffusion at both the film–air (F–A) and film–substrate (F–S) interfaces. We found that the onset of polymer diffusion occurred more rapidly within the skin at the F–A interface at elevated temperatures, but this was quickly surpassed by polymer diffusion at the bottom of the film because of the hydroplasticization effect. The presence of the skin layer retarded water evaporation and extended the time needed for the efficiency of energy transfer to reach its plateau value. We also found that the extent of chain diffusion in the partially cross-linked (XL) films was reduced compared to the non-XL samples because of limited interdiffusion of the polymer that formed the gel content. Dynamic mechanical analysis was employed to investigate the viscoelastic behavior of the samples using time–temperature superposition to generate master curves. We calculated apparent activation energies in the temperature range of the FRET experiments that were consistent with the strong dependence of polymer diffusion rates on the difference between the annealing temperature and glass transition temperature.

Fast drying of biocompatible polymer films loaded with poorly water-soluble drug nano-particles via low temperature forced convection

Engineering of Ganoderma lucidum polysaccharide loaded polyvinyl alcohol nanofibers for biopharmaceutical delivery

Fabrication of Flexible Composite Drug Films Via Foldable Linkages Using Electrohydrodynamic Printing

A predictive transport model for convective drying of polymer strip films loaded with a BCS Class II drug

Continuous preparation of polymer coated drug crystals by solid hollow fiber membrane-based cooling crystallization

A comparison between solvent casting and electrospinning methods for the fabrication of HPMC fast-dissolving films: Investigation of the physicochemical, mechanical and drug release characteristics

Towards nanoporous polymer thin film-based drug delivery systems

3D Printing of Drug Nanocrystals for Film Formulations

Effect of surfactants and drug load on physico-mechanical and dissolution properties of nanocrystalline tadalafil-loaded oral films

Spray Drying of Hydrocolloids: Case Study for Phresponsive and Time-Sustained Release

Enhanced recovery and dissolution of griseofulvin nanoparticles from surfactant-free nanocomposite microparticles incorporating wet-milled swellable dispersants

High drug-loaded amorphous solid dispersions of a poor glass forming drug: The impact of polymer type and cooling rate on amorphous drug behaviour

Preparation and Characterization of Febuxostat Nanosuspension as Fast Dissolving Oral Film

Drug-polymer-water interaction and its implication for the dissolution performance of amorphous solid dispersions.

Facile preparation of solid dispersions by dissolving drugs in <i>N</i>-vinyl-2-pyrrolidone and photopolymerization

Semi-crystalline materials for pharmaceutical fused filament fabrication: Dissolution and porosity

Accelerated removal of solvent residuals from PLGA microparticles by alcohol vapor-assisted fluidized bed drying

Drying-Induced Flash Nanoprecipitation in a Sessile Drop: A Route to Synthesize Polymeric Nanoparticles

Oral fast dissolving films for co-administration of breviscapine and matrine: Formulation optimization and in vitro characterization

Molecular Aspects of Film Formation of Partially Cross-Linked Water-Borne Secondary Dispersions that Show Skin Formation upon Drying

Continuous Synthesis of Polymer-Coated Drug Nanoparticles by Heterogeneous Nucleation in a Hollow-Fiber Membrane Module