Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Experimental Characterization of Non-Associative Plasticity Flow Rule Coefficients for the LS-DYNA MAT213 Model

Progressive failure analysis of 2D woven composites at the meso-micro scale

Multi-Scale Experimental Characterization for LS-DYNA MAT213 Modeling of Composite Structures under High Strain Rate

On the effectiveness of deep material networks for the multi-scale virtual characterization of short fiber-reinforced thermoplastics under highly nonlinear load cases

Experimental characterization of traction-separation laws for interlaminar fracture in geometrically-scaled composites using progressive digital image correlation and through-thickness deformation analysis

A non-quadratic pressure-sensitive constitutive model under non-associated flow rule with anisotropic hardening: Modeling and validation

Micromechanics-based Multiscale Progressive Failure Simulation of 3D Woven Composites under Compressive Loading with Minimal Material Parameters

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

A plasticity concrete material model for DYNA3D

Micromechanical Analysis of Mechanical Response for Unidirectional Fiber-Reinforced Plies

Development of a Numerical Material Model for Axial Crushing Mechanical Characterization of Woven CFRP Composites

Machine Learning- and Finite Element-Based Temperature- and Rate-Dependent Plasticity Model: Application to the Tensile Behavior

Multiscale Modeling of Viscoelastic Behavior of Unidirectional Composite Laminates and Deployable Structures

A Generalized, Computationally Versatile Plasticity Model Framework - Part I: Theory and Verification Focusing on Tension‒compression Asymmetry

LS-DYNA Machine Learning-based Multiscale Method for Nonlinear Modeling of Short Fiber-Reinforced Composites

A numerical multi-scale method for analyzing the rate-dependent and inelastic response of short fiber reinforced polymers: Modeling framework and experimental validation

Analysis and Modeling of Stress-Strain Curves in Microalloyed Steels Based on a Dislocation Density Evolution Model

Validation of Finite-Element Plasticity Models Using Full-Field Surface Strain Measurements

Finite strain anisotropic elasto-plastic model for the simulation of the forming and testing of metal/short fiber reinforced polymer clinch joints at room temperature

Investigation of strain rate dependent microscopic failure mechanisms in short fiber reinforced plastics using finite element simulations

Development of the Concurrent Multiscale Discrete-Continuum Model and Its Application in Plasticity Size Effect