Initial Results From the First Field Expedition of UAPx to Study Unidentified Anomalous Phenomena

M. Szydagis,K.H. Knuth,B.W. Kugielsky,C. Levy
2024-10-17
Abstract:In July 2021, faculty from the UAlbany Department of Physics participated in a week-long field expedition with the organization UAPx to collect data on UAPs in Avalon, California, located on Catalina Island, and nearby. This paper reviews both the hardware and software techniques which this collaboration employed, and contains a frank discussion of the successes and failures, with a section about how to apply lessons learned to future expeditions. Both observable-light and infrared cameras were deployed, as well as sensors for other (non-EM) emissions. A pixel-subtraction method was augmented with other similarly simple methods to provide initial identification of objects in the sky and/or the sea crossing the cameras' fields of view. The first results will be presented based upon approximately one hour in total of triggered visible/night-vision-mode video and over 600 hours of un-triggered (far) IR video recorded, as well as 55 hours of (background) radiation measurements. Following multiple explanatory resolutions of several ambiguities that were potentially anomalous at first, we focus on the primary remaining ambiguity captured at approximately 4am Pacific Time on Friday, July 16: a dark spot in the visible/near-IR camera possibly coincident with ionizing radiation that has so far resisted prosaic explanation. We conclude with quantitative suggestions (3-5 sigma rules) for serious researchers in the still-maligned field of hard-science-based UAP studies, with an ultimate goal of identifying UAPs without confirmation bias toward mundane / speculative conclusions.
Instrumentation and Methods for Astrophysics,Instrumentation and Detectors,Popular Physics
What problem does this paper attempt to address?
The problem that this paper attempts to solve is: How to collect and analyze data on Unidentified Anomalous Phenomena (UAP) through scientific methods and technical means, in order to determine the nature of these phenomena and minimize the confirmation bias towards common or speculative conclusions. Specifically, the research team hopes to identify those phenomena that cannot be explained by conventional explanations through high - quality data collection and rigorous analysis methods, providing a reliable basis for follow - up research. ### Main Problems and Goals 1. **Data Acquisition**: - The research team hopes to capture relevant data on UAP in different environments by using advanced sensors and camera equipment. - They deployed visible - light cameras, infrared cameras, and other sensors (such as magnetic fields, GPS, 3D accelerometers, etc.) to ensure that data can be recorded from multiple angles and within a wide frequency range. 2. **Data Analysis**: - Through preliminary processing and analysis of the collected data, identify possible UAP events. - Use simple methods such as pixel subtraction and more complex algorithms (such as C - TAP) to distinguish between background noise and actual objects, thereby improving the accuracy and reliability of the data. 3. **Result Verification**: - The paper discusses the successes and failures encountered during the first field investigation, especially how to apply the lessons learned to improve future investigations. - The research team paid special attention to a blurry phenomenon captured at 4 am on July 16th Pacific Time - a dark spot that appeared in the visible/near - infrared camera, which may be related to ionizing radiation and has not yet been reasonably explained so far. 4. **Scientific Contribution**: - Propose quantitative suggestions (such as the 3 - 5 σ rule) to provide guidance for serious researchers engaged in UAP research based on hard science. - The goal is to identify UAP through scientific methods and avoid bias towards common or speculative conclusions. ### Formula Representation In the data analysis section, the paper mentions some formulas for image processing. For example, the formula for calculating the standard deviation \(\sigma_a\) is as follows: \[ \sigma_a=\sqrt{\Delta R^{2}+\Delta G^{2}+\Delta B^{2}+\Delta r^{2}+\Delta g^{2}+\Delta b^{2}} \] where, \[ \Delta R = M_R-\mu_a,\quad\Delta r = M_r-\mu_a \] Similarly, the same calculation method is also applicable to \(G, g, B, b\). The average value \(\mu_a\) is defined as: \[ \mu_a=\frac{M_R + M_G+M_B+M_r+M_g+M_b}{6} \] Here, \(M\) represents the maximum or minimum pixel difference, and \(p\) represents an 8 - bit (0 - 255) pixel value. Through these formulas, the research team can distinguish between noise and actual objects in the image, thereby improving the quality and credibility of the data.