The Power Board of the KM3NeT Digital Optical Module: design, upgrade, and production

S. Aiello,A. Albert,S. Alves Garre,Z. Aly,A. Ambrosone,F. Ameli,M. Andre,E. Androutsou,M. Anguita,L. Aphecetche,M. Ardid,S. Ardid,H. Atmani,J. Aublin,F. Badaracco,L. Bailly-Salins,Z. Bardacova,B. Baret,A. Bariego Quintana,S. Basegmez du Pree,Y. Becherini,M. Bendahman,F. Benfenati,M. Benhassi,D. M. Benoit,E. Berbee,V. Bertin,V. van Beveren,S. Biagi,M. Boettcher,D. Bonanno,J. Boumaaza,M. Bouta,M. Bouwhuis,C. Bozza,R. M. Bozza,H.Branzas,F. Bretaudeau,R. Bruijn,J. Brunner,R. Bruno,E. Buis,R. Buompane,J. Busto,B. Caiffi,D. Calvo,S. Campion,A. Capone,F. Careniniu,V. Carretero,T. Cartraud,P. Castaldi,V. Cecchini,S. Celli,L. Cerisy,M. Chabab,M. Chadolias,C. Champion,A. Chena,S. Cherubini,T. Chiarusi,M. Circella,R. Cocimano,J. A. B. Coelho,A. Coleiro,S. Colonges,R. Coniglione,P. Coyle,A. Creusot,G. Cuttone,R. Dallier,Y. Darras,A. De Benedittis,B. De Martino,V. Decoene,R. Del Burgo,I. Del Rosso,U. M. Di Cerbo,L. S. Di Mauro,I. Di Palma,A. F. Díaz,C. Diaz,D. Diego-Tortosa,C. Distefano,A. Domia,C. Donzaud,D. Dornic,M. Dorra,E. Drakopoulou,D. Drouhin,R. Dvornicky,T. Eberla,E. Eckerova,A. Eddymaoui,T. van Eeden,M. Eff,D. van Eijk,I. El Bojaddaini,S. El Hedri,A. Enzenhofer,et al. (184 additional authors not shown)

2023-11-25

Abstract:The KM3NeT Collaboration is building an underwater neutrino observatory at the bottom of the Mediterranean Sea consisting of two neutrino telescopes, both composed of a three-dimensional array of light detectors, known as digital optical modules. Each digital optical module contains a set of 31 three inch photomultiplier tubes distributed over the surface of a 0.44 m diameter pressure-resistant glass sphere. The module includes also calibration instruments and electronics for power, readout and data acquisition. The power board was developed to supply power to all the elements of the digital optical module. The design of the power board began in 2013, and several prototypes were produced and tested. After an exhaustive validation process in various laboratories within the KM3NeT Collaboration, a mass production batch began, resulting in the construction of over 1200 power boards so far. These boards were integrated in the digital optical modules that have already been produced and deployed, 828 until October 2023. In 2017, an upgrade of the power board, to increase reliability and efficiency, was initiated. After the validation of a pre-production series, a production batch of 800 upgraded boards is currently underway. This paper describes the design, architecture, upgrade, validation, and production of the power board, including the reliability studies and tests conducted to ensure the safe operation at the bottom of the Mediterranean Sea throughout the observatory's lifespan

Instrumentation and Methods for Astrophysics,Instrumentation and Detectors

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to design, upgrade and produce efficient and reliable power boards (PB) for the Digital Optical Module (DOM) of the KM3NeT neutrino telescope. Specifically, the paper focuses on the following aspects:

1. **Providing a stable power supply**: Various components in the DOM, including 31 photomultiplier tubes (PMTs), calibration instruments and data acquisition electronics, etc., require a stable and precise power supply. The design of the PB aims to ensure that these components can operate reliably in the deep - sea environment.

2. **Improving efficiency and reliability**: In order to reduce power consumption and improve the overall reliability of the system, the researchers have upgraded the PB. The upgraded PB uses a more efficient DC/DC converter and its performance has been verified through a series of strict tests.

3. **Adapting to extreme environments**: KM3NeT is located at the bottom of the Mediterranean Sea, and the environmental conditions are extremely harsh, such as high pressure, low temperature and high humidity. The PB must be able to work stably for a long time under these conditions, so anti - interference and thermal management issues are specially considered in the design.

4. **Optimizing the startup sequence**: The PB needs to generate a monotonic startup voltage sequence that meets the requirements of Xilinx FPGA to avoid current shock. For this purpose, a sequence generator is built in the PB to control the startup order of different voltage rails.

5. **Real - time monitoring and protection mechanisms**: In order to ensure the safety and stability of the system, the PB is equipped with a monitoring system that can read each voltage rail and current value in real time and send the data to the Central Logic Board (CLB) for monitoring through the I2C interface. In addition, a variety of protection mechanisms, such as over - voltage protection and low - voltage lock - out, etc., are also added.

In summary, this paper describes in detail the design concept, architecture details, performance optimization measures and quality control processes for mass production of the PB in the KM3NeT project, aiming to provide solid technical support for future deep - sea astronomical observations.